Having problems with your Campbell Hausfeld Pressure Washers ?

Hard starting 6hp Briggs and Stratton power washer engine. I poured a teaspoon of gas into the cylinder; reinserted the spark plug and with one pull in ran fine. This is a choke start engine and it may take 12 to 15 pulls to start on a cold engine. The unit is clean. The air cleaner is new. The spark plug is new. The unit is 2 years old with very little use.


Answers :

Hello. I have this same machine. Go to the auto parts store and get an aerosol can of starter fluid. Have a helper squirt some into the air intake while you start it. Then continue to squirt a little starter fluid as it runs for the first two minutes. Finally, also pick up a bottle of a fuel additive called seafoam. Follow the directions regarding how much to add per gallon of fuel and use it in your power washer til the bottle is used up. It will then start and run like it did when it was new, I assure you. Joe
Repair Help & Product Troubleshooting for Campbell Hausfeld Pressure Washers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Hard starting 6hp Briggs and Stratton power washer engine. I poured a teaspoon of gas into the cylinder; reinserted the spark plug and with one pull in ran fine. This is a choke start engine and it may take 12 to 15 pulls to start on a cold engine. The unit is clean. The air cleaner is new. The spark plug is new. The unit is 2 years old with very little use.


Hello. I have this same machine. Go to the auto parts store and get an aerosol can of starter fluid. Have a helper squirt some into the air intake while you start it. Then continue to squirt a little starter fluid as it runs for the first two mi ... Campbell Hausfeld Pressure Washers

My Honda 2600 psi power washer will not pull to start. It was running great then I allowed the neighbor to borrow it. He ran the washer till it was out of gas and proceeded to refuel and at this point it would no longer start. The pull cord is out about 4-6 inches out and I am concerned about taking the casing off myself. Fearing that it may throw more off on the unit. If i take the casing off are there any spring loaded parts that will dismount? What should I do? Spark Plug? Turn


You should be fine to take the recoil off, there shouldn't be anything that shoots out at you. You might want to check the oil level on the engine, many of the Honda engines won't start unless there is enough oil in them. If your oil level is fine, c ... Honda Pressure Washer PSI 3000

11 hp honda pressure washer engine won't start. No spark at the pkug, bought a new coil and still no spark. This sysem only has a coil off the fly wheel and the spark plug. I even changed spark plug. Use the unit the other day, shut it down and on restart it won't start. Also, I disconnected the kill switch and the il lvel sensor so nothing was going to ground.


If you replaced the coil,check the wire and boot,check with meter for continuity.could be loose connection to spark plug ... Honda Pressure Washer PSI 3000

I have a Karcher 2,600 PSI 2.3 GPM Gas Pressure Washer G 2600 VHR that I have used once last summer. I have stored the PW in my basement with no fuel in the gas tank. The PW was never exposed to freezing temps. I cannot get the PW to start. I put new fuel into the tank, the oil is good, I drained the carburetor, and the spark plug works (tested it). I pull the cord and the engine doesn't turn. Fuel value is on, choke is pulled, and the starter switch is turned on. System is practically brand new


Hi I have a similar pressure washer from Kartcher and the same scenario as yours I have owned it for about 2 years and noticed that it was getting harder and harder to start with each time I use it which is months. If your pw has a honda engine on i ... Karcher G 2600 VH Gas Pressure Washer

I HAVE A NEW CRAFTSMAN PRESSURE WASHER WITH KEY START. I HAVE USED IT ONCE AND WHEN I TRIED TO START IT IT WAS HARD TO START HAD TO PULL START IT. NOW IT WONT START. LET PRESSURE OUT HAVE HOSE OH AND RUNNING, NEW SPARK PLUG HAS OIL, GAS FILTER FINE.HAS GOOD COMPRESSION, BUT WILL NOT FIRE GET SOME RECOIL. GETTING GAS TO SPARK PLUG AND GETTING SPARK. IM LOST PLEASE HELP.


... Pressure Washers

I have a generac pressure washer and the engine will not turn over. Followed the directions to a T and when I pull the cord... nothing. Spark plug? It is brand new out of the box. Filled high with brand new mid octanne gas, filled oil, followed directions to start... nothing.


... Pressure Washers

Very Hard to Pull Cord to start engine on Northstar Pressure Washer. When I remove spark-plug it is very easy to pull cord. With plug reinserted it is extremely difficult to pull cord to start engine.


On the Honda motors very hard pull starting with no start ck for broken rocker on exhaust or intake, I've already repaired two with this problem...... ... Northstar Pressure Washer 3000 PSI

I have a Craftsman 2700 psi pressure washer with a Briggs and Stratton 850 engine (80 year anniversary special addition) . It is about 2 years old and used very little and will not start. I filled it with fresh fuel and checked the oil. I also replaced the spark plug and air filter. I checked the fuel line thinking it may not be getting fuel, but there is no obstruction from the tank to the end of the fuel line. I am out of TS options short of taking it to a service center.


Here is the long answer with everything we learned while using a power \015\012washer twice a day for years::\015\012It sounds like could be one of the problems listed below or a \015\012combination of those things.\015\012\015\0121 ... Briggs Stratton 020273 Elite Series Portable Gas Pressure Washer

Briggs and Stratton pressure washer will not start. I have a 6.75 hp pressure washer that is only a year old. when I pull cord it turns over but does not start. I changed plug and checked it, I have spark when pulling. I have 40-50 psi of compression when pulling also. gas was drained and is brand new. it was working fine last time it was used. I have tried starting it without the water line or spray wand hooked up and no difference. After about 10 or 15 pulls, can smell gas when I am trying to


Hello dave, the problem is compression to low,you need 60 to 130 lbs to run engine,check for blown head gasket,or bad rings,or a stuck open valve,hope this helps,, ... Briggs & Stratton Pressure Washers

I have a craftsman Pressure washer Model 580-725400 the unit has ran great until today. I last used the unit 1 week ago with no problems but now I have to run the machine almost full choke to get it it rev up and run smooth. The engine oil is clean and filled to the proper point. The spark plug is new and gapped proper. The air filter is new also. And the gas is 97 Oct and fresh. When it choke it to crank the engione I move the choen to run and the engine struggles to run. When I move the choke


... Craftsman Pressure Washers

Washer won't start tried everything , I could think of changed spark plug tried new gas , Two things that bother me are . if i take out the spark plug and put my thumb over the spark plug hole theres no pressure and the wire that comes from the coil to shut off the pw it has continunity from the coil to the pin that sticks up to shut off the pw but it also has continuity from the coil to all parts of motor.


... Pressure Washers

I have a Husky 2600 PSI power washer with the Honda GCV160 engine that I can't get to start. It was okay when I purchased it from Home Depot last spring but now I've tried putting new gas in it, spraying carb cleaner, new spark plug, and it still won't start. I only ran it for about 30 minutes when I first purchased it. The guy at the service desk at Home Depot told me that the water hose should be attached and turned on while trying to start. Is this true or would this be starting the motor und


You can eliminate the motor by unbolting the pump from it and then if it will start the problem is with the pump or the unloading valve.If it does not start with the pump removed then you check for spark and get the carb cleaned or have a kit put in ... Karcher 2500 PSI Pressure Washer

Have a genarac pressure washer when trying to start the engine catches half way through the pull with spark plug out it cranks fine


... Briggs & Stratton Power Products 1539 Pressure Washer

I have an Excell VR2500 pressure washer with B & S 6.5 HP engine. It was running fine, but then stalled out and now will not start. Has clean gas and full oil. I pulled the spark plug it is producing a sufficient spark when starter cord is pulled. Any ideas what might be causing the problem? Please help.


The key things to check are the spark plug, the air filter, the fuel. If those are all new and in good shape then you probably have gum in the carburator. Get a can of starter fluid and a helper. One person squirt the starter fluid into the air in ... Briggs & Stratton Pressure Washers

I have a 2500 craftsman power washer with a Briggs and Stratton engine. I used it about a month ago and it worked fine. Took it out yesterday and I could not pull the rope to get it started. I took out the spark plug to release the compression but I still could not pull the rope out it is locked any advice.


It sounds like the pump is seized. Make sure any pressure has been released by pulling the trigger on the gun. Sometimes this will allow you pull the cord. If the pump is seized, a new pump would be in order. ... Briggs & Stratton Pressure Washers

My gas power washer will not start. I filled the gas, checked the oil, set the choke, made sure it was on, changed the spark plug, checked the air filter, and drained any water. When I pull the cord to start I don't even get a putter. Anything else I can try or do I need to take it to a service place.


Will it run if you pour a small amount of gas in the carb? If so, it's a fuel supply problem. Most likely a stuck closed float needle. ... Honda Maxus Pressure Washer MX5222

I can't pull the cord out in order to start the unit. Even took the spark plug out. The unit was running fine then quit. No unusual noises or anything. Sitting on a deck so nothing was able to get underneath.


... Pressure Washers

Engine starts, but when i push in the choke, it kills. i just replaced the spark plug, drained the gas and oil and replace with new gas and oil. Starts fine when choked, but when i push in the choke, it dies.


... Honda 50 W Ar Pump 2500 Psi 25 Gpm Pressure Washer

I have a Baldor 6000W generator with a gx340 11hp engine. I have drained the tank and carb and put new gas and sea foam in it. Also I have replaced the spark plug and fuel filter. The engine will start/run as long a I spray starting fluid in the carb. But it will not continue to run without it. Also I just checked the oil level and that is good. Please help!!!


It sounds like the engine is not getting enough fuel for it to run. First check that you have the fuel tap in the on position. If the fuel tap is on then the carby might be blocked or the needle & seat are not working properly. Turn the ... Honda 8 HP Engine

I have a mid 60's 6 hp Tecumseh engine on a Troybilt tiller. I used it to till my front yard and it ran fine. I let a friend use and it quit on him after a few minutes. It will not start. It has spark at the spark plug. I have thoroughly cleaned the carburetor by taking it apart, soaking it in cleaner, blowing out all holes and passages. I made sure the tiny holes in the power valve at the bottom of the fuel bowl are open. I have taken this carburetor apart five or six times over the years an


... Karcher 2500 PSI Pressure Washer

Won't start I have checked the spark plug and I have good saprk. I have checked the fuel sysstem and the primer bulb injects fuel. I have removed the head and cjecked for engine damage and all cycle correctly. Vaves opne on time piston shows no dmagae. side walls are smooth and not damaged. This engine was working fine but the pressure washer needed some O rings replaced. I have tried to start it with and without the pump attahced. Evrything on the engine looks fine. I removed the spark plug and


... Briggs & Stratton Briggs Stratton 2550 Psigaspressure Washer

My porter cable 2400 psi pressure washer will not start. has honda engine gc160. pulled plug and put up against frame and it has spark. It's full of oil.


... Porter Cable Cable Commercial Pressure Washer PCH3200

Honda GC190 no start. Unit has been sitting for 2 years. Drained old gas, cleaned the carb. No go. New plug gapped to 0.030in. Still nothing. spark seems good. Cleaned the fuel strainer and there IS a bit of vacuum at the fuel pump when cranking. Poured a dab of gas into combustion chamber.. Still won't "talk to me" AT ALL. Removed valve cover and checked the valves.. within specs and nothing sticking or hanging up. Timing belt and cam looks good. Took a peak at the coil.. air gap in specs. 1ohm


... Karcher 2500 PSI Pressure Washer

Bought unit new last summer. Used it once last summer and once this year. It started fine both times. Today, it will not crank. I have replaced the spark plug, checked the air filter (it is clean), gas tank is full and added oil. Why won't it crank?????


Unable to crank? Do you mean unable to start?If you leave gasoline inside tank over long period of time, that will 'gum-up' and ruin carburetor.To prevent problem, put additive in gasoline or empty gas from tank:: under gas tank sho ... Craftsman Pressure Washers

Unable to start gas engine on a NorthStar pressure washer


Disassemble and clean the carb. If it ran briefly with the starer fluid then gasoline is not coming through the carb. ... Northstar Pressure Washers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1578 seconds