Having problems with your Campbell Hausfeld PW2102 Gas Pressure Washer ?

My 2100 will not pull up the cleaner solution. Hose is not kinked, I have primed it, and nipple does not appear to be plugged.


Answers :

THE DETERGENT HOSE USES THE VACUME FROM THE WATER MOVING THRU THE PUMP TO DRAW THE SOAP INTO THE PUMP.
\015\012CHECK THE AREA WHERE THE HOSE CONNECTS TO THE PUMP THERE SHOULD BE A SMALL BALL CHECK THAT MAY BE STUCK AND NOT LETTING THE VACUME PULL THE SOAP
First thing to try is place mix on its lowest setting, run, and slowly increase.
Repair Help & Product Troubleshooting for Campbell Hausfeld PW2102 Gas Pressure Washer

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My 2100 will not pull up the cleaner solution. Hose is not kinked, I have primed it, and nipple does not appear to be plugged.


THE DETERGENT HOSE USES THE VACUME FROM THE WATER MOVING THRU THE PUMP TO DRAW THE SOAP INTO THE PUMP.\015\012CHECK THE AREA WHERE THE HOSE CONNECTS TO THE PUMP THERE SHOULD BE A SMALL BALL CHECK THAT MAY BE STUCK AND NOT LETTING THE VACUME PUL ... Campbell Hausfeld PW2102 Gas Pressure Washer

Hard starting 6hp Briggs and Stratton power washer engine. I poured a teaspoon of gas into the cylinder; reinserted the spark plug and with one pull in ran fine. This is a choke start engine and it may take 12 to 15 pulls to start on a cold engine. The unit is clean. The air cleaner is new. The spark plug is new. The unit is 2 years old with very little use.


Hello. I have this same machine. Go to the auto parts store and get an aerosol can of starter fluid. Have a helper squirt some into the air intake while you start it. Then continue to squirt a little starter fluid as it runs for the first two mi ... Campbell Hausfeld Pressure Washers

Honda pressure washer won't pull chemical. Line is not kinked. Removed intake fitting anf checked for clogs - not clogged. Appears to be drawing but not enough to pull the clorox bleach from the bottle. Using the soap fitting so that's not the issue either.


... Honda 2500 PSI Gas Pressure Washer

Karcher 2400R I have not used my pressure washer for 6 months. It was left full of gas in the garage. I tried to start it but it would not fire up so I change the gas, oil, and spark plug, took apart the carburator and cleaned it out with carb cleaner. I went ahead and put everything together, pull the cord and wanted to start. While trying to start it after I sprayed starting fluid in the air cleaner I noticed that gas was coming back from the crankcase breather hose into the air filter choking


You have a poor signal to the spark plug usually caused by a rusty fly wheel found underneath the pullcord casing. clean it with releasing ajent such as wd 40. common when not in use for a while. ... Karcher 2500 PSI Pressure Washer

John Deere 3300 PSi pressure washer shutting off while in use.Everything appears fine Oil level,Gal level,Air cleaner ok etc.. May run 2 minutes or 12 minutes then spudders a bit then Bang "Off" as if i turned it off.May or may not restart after a couple of pulls.


John Deere will replace the cap for free; they acknowledge the vendor who supplied Briggs & Stratton gas caps provided faulty caps. Call 1-888-228-3068 then 1 (English), 2, 1 and a technician will ask you for model number and Serial Number ... Dewalt 3800 PSI Pressure Washer

Very Hard to Pull Cord to start engine on Northstar Pressure Washer. When I remove spark-plug it is very easy to pull cord. With plug reinserted it is extremely difficult to pull cord to start engine.


On the Honda motors very hard pull starting with no start ck for broken rocker on exhaust or intake, I've already repaired two with this problem...... ... Northstar Pressure Washer 3000 PSI

Westinghouse Dishwasher Model SB907W5*08 the dishes are not getting cleaned & it appears that it is not heating as i bought a bottle of dishwasher cleaner & the dishwasher is supposed to heat up enough to dissolve the lid off the cleaner to let the fluid out. after putting the cleaner through a cycle the cleaner lid was still there. i think this must mean that the heating element is broken? this is out of warranty & can't remember how much it cost us so don't know whether better off gettin


Hi\015\012If you are observing that the dishes are not clean, then you'll need to follow certain steps to be sure where exactly the issue. First thing to check for is the detergent cup and spray arms. Check if the dishwasher's spray arms are w ... Westinghouse 24 in. MDP531 RF Free-standing Dishwasher

Briggs and Stratton pressure washer will not start. I have a 6.75 hp pressure washer that is only a year old. when I pull cord it turns over but does not start. I changed plug and checked it, I have spark when pulling. I have 40-50 psi of compression when pulling also. gas was drained and is brand new. it was working fine last time it was used. I have tried starting it without the water line or spray wand hooked up and no difference. After about 10 or 15 pulls, can smell gas when I am trying to


Hello dave, the problem is compression to low,you need 60 to 130 lbs to run engine,check for blown head gasket,or bad rings,or a stuck open valve,hope this helps,, ... Briggs & Stratton Pressure Washers

We have a Kenwood KDW8ST2A Dishwasher which is about a month old. The other day we had to pull it out from under the worktop because something rolled under it. When we put it back and went to use it later that day, we got an E1 error code appear and it's been like that since. We pulled it back out to make sure that we hadn't accidently pulled or loosened any of the pipes. We have the manual which does tell us what the error means but it doesn't tell us how to fix it. I'm sure it must be somethin


You can find a manual here ... Dishwashers

My 6 hp honda motor has become very hard to pull. It is on a pressure washer. I even removed the pump but still pulls hard.it runs if you can get it started but dosnt seem to be running at full power.I pulled the spark plug and it spins easily. Help!


When you remove the spark plug and it turns easily that means that the valves aren't opening properly. When the spark plug is installed and its hard to turn over, its because the valves (possibly just the exhaust valve) are sticking shut and the pre ... Pressure Washers

How do I disconnect the electrical wire plugs from the door handle in order to replace the handle? The plugs won't pull straight off and so I am wondering if there is any piece of equipment needed to disengage the plugs from the prongs.


First shut off the power to the dish washer. The plugs are just verry hard to pull off. You may brake the switch on the old handle but if you have the right new part it should have new switches on it. Just pull hard side to side wiggle off. ... Maytag 24 in. MDB5600A Jetclean II Built-in Dishwasher

Won start Was using the pressure washer 1st time this year and started on the second pull. Ran out of gas shut-off also noticed it needed oil. Believe, I put too much oil so, I drained some and added gas. At first, there was no resistant in the pull so waited an hour and tried again. This time the resistant was there on the pull but still would not start; no attempt even to turn over. It's been a couple of days...changed the spark plug although, hardware guy said nothing was wrong with it..still


... Briggs Stratton 020273 Elite Series Portable Gas Pressure Washer

The inside of the dishwasher used to sparkle & clean the dishes very good, now the dishes look dirty & inside looks dull with a white film. I have tried cleaning filters & taking arms offs to check for blockage, making sure the Jet Dry dispenser is properly filled, the hose going to the dishwasher does not appear to be kinked, how would I check inside the dishwasher to see if it's kinked there? Do you have any other suggestions? please help!!!!


Hi, \012I have an older dishwasher also and recently mywife also complained about it not cleaning right... so me being the man I amtried in vain to clean the things... Bought new spray arms online and installedthem in minutes...now the thing works li ... Bosch 23 in. SHU33A Built-In Dishwasher

My Honda 2600 psi power washer will not pull to start. It was running great then I allowed the neighbor to borrow it. He ran the washer till it was out of gas and proceeded to refuel and at this point it would no longer start. The pull cord is out about 4-6 inches out and I am concerned about taking the casing off myself. Fearing that it may throw more off on the unit. If i take the casing off are there any spring loaded parts that will dismount? What should I do? Spark Plug? Turn


You should be fine to take the recoil off, there shouldn't be anything that shoots out at you. You might want to check the oil level on the engine, many of the Honda engines won't start unless there is enough oil in them. If your oil level is fine, c ... Honda Pressure Washer PSI 3000

I have a 2500 craftsman power washer with a Briggs and Stratton engine. I used it about a month ago and it worked fine. Took it out yesterday and I could not pull the rope to get it started. I took out the spark plug to release the compression but I still could not pull the rope out it is locked any advice.


It sounds like the pump is seized. Make sure any pressure has been released by pulling the trigger on the gun. Sometimes this will allow you pull the cord. If the pump is seized, a new pump would be in order. ... Briggs & Stratton Pressure Washers

I HAVE A NEW CRAFTSMAN PRESSURE WASHER WITH KEY START. I HAVE USED IT ONCE AND WHEN I TRIED TO START IT IT WAS HARD TO START HAD TO PULL START IT. NOW IT WONT START. LET PRESSURE OUT HAVE HOSE OH AND RUNNING, NEW SPARK PLUG HAS OIL, GAS FILTER FINE.HAS GOOD COMPRESSION, BUT WILL NOT FIRE GET SOME RECOIL. GETTING GAS TO SPARK PLUG AND GETTING SPARK. IM LOST PLEASE HELP.


... Pressure Washers

I pulled the power stater pull string but my powerwasher won't turn on, there's gas, the water hose is on, could it be the spark plug?


You can check for spark by unscrewing the spark plug , place the rubber boot back on the plug and have someone gently pull the starter rope while you hold the electrode of the plug so that it touches the engine block. make sure not to touch any part ... Mi T M WP-3000-4MHB Pressure Washer

HI, I have a Karcher Model K2400 and the pump stopped working. I took it apart and found the 'cheese head' screw had broken. there didn't appear to be any other problem with the pump so i am replacing the screw only. my question is how much pump oil should be put in the reservoir upon assembly as there doesn't appear to be a fill/drain plug?


... Karcher 2500 PSI Pressure Washer

My Frigidaire FDB956RBC0 has been having trouble resetting on the control panel for a new load. At first I could push several buttons or wait a little bit for it to reset then I could push start. Now I have to open the front panel & pull out a yellow & white plug, then plug it back in to reset the buttons for a new load.


... Frigidaire FDB956RB Built-in Dishwasher

I have a Karcher 2,600 PSI 2.3 GPM Gas Pressure Washer G 2600 VHR that I have used once last summer. I have stored the PW in my basement with no fuel in the gas tank. The PW was never exposed to freezing temps. I cannot get the PW to start. I put new fuel into the tank, the oil is good, I drained the carburetor, and the spark plug works (tested it). I pull the cord and the engine doesn't turn. Fuel value is on, choke is pulled, and the starter switch is turned on. System is practically brand new


Hi I have a similar pressure washer from Kartcher and the same scenario as yours I have owned it for about 2 years and noticed that it was getting harder and harder to start with each time I use it which is months. If your pw has a honda engine on i ... Karcher G 2600 VH Gas Pressure Washer

Whirlpool GU1100XLTQ1 dishwasher, 4 years old is leaking water during cycle. I cannot see exactly what is leaking by looking up through the acess panel in front...there are what appear to be plastic support ribs for the tub and water is leaking through several of them to the left of what appears to be the motor in the center...please help! I don't think I can run the washer and tilt it back at the same time as the water supply line only allows me to pull it out just enough to clear the counter t


Hi,\012Here is a tip that I wrote about dishwashers and them leaking.Leaking Dishwasherheatman101\012\012\012wahgfadh ... Whirlpool GU1100XTLB / GU1100XTLQ / GU1100XTLT Built-in Dishwasher

THE DISHWasher drains into the garbage disposal, there appears to be a plug in the disposal unti blocking the drain. how do i remove the plug? The disposal unit is ACE 2000 1/2hp. thanks


Take a flat blade screwdriver and hammer / hit it good and it will pop out . make shure you remove the dime sized plug or your disposal will sound very bad .. mm ... Dishwashers

UNIT TIPPED OVER IN TRUCK OIL IN CYLINDER PULLED PLUG AND REPLACED PLUG NOW WONT START


... Pressure Washers

Hi I have a brand new Honda Power washer GC 160,2600 psi 2.3 GPM my husband taught me how to use it last night and I think I have followed all of steps: 1. hose free of kinks 2. connected to machine 3. purged pw handle of air and made sure water from house coming through 4. pulled out choke 5. turned red button to "ON" position 5. pulled T handle enging starter and it sounds like it will start but doesnt what am I doing wrong??? yes it does have gas in the fuel tank.


... Karcher 2500 PSI Pressure Washer

No kinks in the line. Vent at sink is clear. Will pump some water just not all of it. Pulled left side panel off and removed hoses-no blockage. Pulled drain hose off and turned plump on, seemed to have good pressure/volume. Is this a timer issue? or control panel? Model SHU4022UC/U06


Alright, so you have a Slow Filling Dishwasher. In order to keep small particles of dirt and minerals out of the pumps and nozzles of dishwashers, manufacturers install a small screen in the primary inlet water line to trap any contaminants. Over ti ... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0458 seconds