Having problems with your Campbell Hausfeld PW2575 Pressure Washer ?

My pressure washer only has a low pressure and volume. I can hear the motor speed changing but no more pressure


Answers :

Repair Help & Product Troubleshooting for Campbell Hausfeld PW2575 Pressure Washer

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My pressure washer only has a low pressure and volume. I can hear the motor speed changing but no more pressure


... Campbell Hausfeld PW2575 Pressure Washer

I change oil on my 3700 psi honda motor pressure washer motor and pump and after i done that the tigger rope is to hard to pull looks like some who is pressure some where can some one help me whit this problem .. thank you


Most likely has nothing to do with oil change. Have someone hold the trigger on handle open to relieve pressure on system/pump , this will make engine turn easier when you pull rope. ... Karcher 2500 PSI Pressure Washer

Pressure Washer I have a Porter Cable pressure model no.PCH2401.It works fine for 5 minutes,then I can hear the motor loading down and then it stalls out. I tried to start it and it was very hard to pull on. disconnected the water supply and if was very easy to pull and started right up. I noticed the pump was very hot.This unit has a thermal relief valve on it,shouldn't it have released when it gets to a certain temperature .I was thinking maybe this is why it might be shutting the motor


Any leaks from connection at pump to gun and wand assembly if so the valve is detecting leakage and open up again without u squeezing trigger it builds up in the head.if your trigger gun is leaking internally then you will need to replace the gun thi ... Pressure Washers

North Star Model 157597 Pressure Washer from Norther Tool calims to have adjustable pressure. There is nothing in the manual about how to adjust the pressure and I have received two statements from them on how to adjust the pressure: 1. Adjust the pressure at the unloader valve 2. Run the motor at reduced speeds. Which, if either is correct?


... Pressure Washers

PRESSURE WASHER WON'T PUT OUT FULL PRESSURE WHEN SQUEEZING TRIGGER, THIS HAPPENED A OF A SUDDEN. USUALLY WHEN THE TRIGGER IN THE HANDLE IS SQUEEZED THE ENGINE NOTE CHANGES & THE PRESSURE GOES UP. NOW THE ENGINE SPEED STAYS THE SAME & PRESSURE GOES UP SLIGHTLY, NOT ALL THE WAY.


... Pressure Washers

John deere A 16 pressure washer electric, pump faltering, intermitent pressure changes, motor seems okay running independently. Are parts for A16 pumps available?


... Electric Pressure Washers

How do i change the oil in my troy bilt briggs and stratton motor pressure washer?


... Briggs & Stratton Pressure Washer Projectpro Spray Nozzle

Washer won't start tried everything , I could think of changed spark plug tried new gas , Two things that bother me are . if i take out the spark plug and put my thumb over the spark plug hole theres no pressure and the wire that comes from the coil to shut off the pw it has continunity from the coil to the pin that sticks up to shut off the pw but it also has continuity from the coil to all parts of motor.


... Pressure Washers

I bought a troybuilt pressure washer used and i changed the motor oil and ran it maybe 5 minutes. later i checked the oil level again and it shot out the cap and i noticed the pump oil level is also almost to the top of sight glass. Does anyone know whats wrong?


If you left it sit for a while & did not turn the fuel tap off,it may have flooded and therefore the oil level would have risen causing the oil to over flow.\015\012\015\012always turn the fuel tap off when not using your pressure wahser. ... Honda Pressure Washer PSI 3000

Troy built 2350 psi 2.0 gpm. pressure washer. starts onne then dies. will not start again. has briggs and straton motor. has been sitting up for the winter. have changed spark pulg. checked air filter that is clean, has oil and gas.


... Pressure Washers

Wont start I have a North Star pressure washer that has been in storage for three years.It has the Honda motor GX 160 5.5 I put in new gas changed the oil, air filter,and spark plug.But it wont kick over. Im not sure how to work the levers upon starting it.Theres one for gas, choke,idle,and of course an on switch.Please help


Tip a cap full of fuel in top of the carb to start intitially, check for spark as common fault is on/off switch, If no spark, link the 2 wires on on/off switch together. ... Pressure Washers

Shark pressure washer with honda 5.0hp motor when in use spraying with good pressure it the pressure shuts off and motor sounds like its about to shove a rod through the cases shut it off restart it andd the same thing occurs all fluid levels good pump and motor. water pressure from hose bib good. may b low water pres. for short time due to possible kink in hose reel not sure


What type pump oil to usefor karcher 2400 psi ... Honda Pressure Washers

I accidentially sprayed water on the pressure washer motor and got it wet and the pressure washer stopped and won't start up. Will it start back up after things dry out or is the motor broke?


Yes it most likely will, BUT you need to dry OFF ALL electrical items well.\015\012\015\012Check also that you haven't dislodged anything from the system.\015\012\015\012If it still will not go, you may need to use WD40 or similar water d ... Pressure Washers

I have a Generac pressure washer, model #01450-0, with a Honda 5hp motor. The motor runs fine, but the pressure hose pulsates as if the pump is intermittently making pressure, and the pressure out of the sprayer is about half of what it should be. A friend suggested replacing the seals in the unloader. I bought an unloader kit, replaced everything and it still runs the same. It will build a small amount of pressure, spray for a few seconds, then the pressure dropps to almost nothing. Any help ap


Take a small diameter wire and poke thru the discharge hole of the spray head to clean out.\015\012Second time in 6 months that I had the same problem. The problem is alway in the spray head. ... Pressure Washers

My Karcher K3.48M pressure washer remains in the low pressure mode even when I return the pressure nozzle to the high pressure position. How can this be corrected. The pump seems to build up the pressure because when I release the handle the pump motor stops. This is a fairly new pump which was purchased in the latter part of last year(2010). Could this have been caused by the detergent I have been using which is an automotive shampoo? Please help I love this washer and for the times that I u


... Karcher PSI Electric Pressure Washer

Deville Excel Model # EXHA2425 Pressure washer I have a deville excel Model # EXHA2425 pressure washer. I went to the deville website (devap.com) which forwarded me to the dewalt site w/ exploded diagram below. I am having problems with intermittent pressure production. If I squeeze the trigger sometimes it will have pressure, somethings it will not. If I repeatedly squeeze, then release the trigger sooner or later I will get pressure. Someone on hear had told me it was a "bypass valve sticki


You\015\012need toput antifreeze in the out/outlet or/oil then start it up you are driing out the seals allways put away with repeating this step ... Karcher 2500 PSI Pressure Washer

I have a Karcher 330 electric power washer. When connected and set to highest pressure (on variable wand) I get no motor action unless I reduce wand setting, then I get a little boost but not much. If I use high pressure conical wand I get high pressure sometimes, other times motor does not go and no pressure is delivered. I have replaced the high pressure hose.


Just wondering. have you tried it without an attachment to see what kind of pressure you get ... Karcher K2.26 Electric Power Washer

If while pressure washing I let off the wand trigger it looses pressure and I have to turn of the washer motor and wait for the pressure to return.(seems like some kind of vapor lock problem)When the pressure returns I hold the trigger and restart the washer. If I let off the trigger we go through the same process again. this is a g3050


Hi and welcome to FixYa, I am Kelly. \015\012 This is most often caused by the bypass / un-loader valve located on the high pressure output side of the pump. The valve will either have a stem type valve with a knurle ... Karcher 2500 PSI Pressure Washer

I have the Coleman powermate 2400 PSI pressure washer and on initial start it sprays and has great pressure. But once I release the spray handle it will not spray again, not even one drop of water. I have verified water pressure, bought 3/4 hose, and also changed the spray handle with no help. Pressure washer was bought new at Lowes, but did not use for first three years of ownership, should have tested it. Thanks for any help on this. Ted Miller


Sounds like the valve in the handle is sticking closed. May have a broken spring, or maybe a part is stuck..\015\012I say take it apart, and the answer will present itself.. Play with it with nozzle out too... Maybe something is stuck after st ... Coleman Pressure Washers

Hi- I have a Simoniz S1600 pressure washer and usually when I first turn it on, the motor turns on to build up pressure. Now the motor won't kick in no matter what I do. Water still comes out of the gun as a small stream but there is no pressure. There are no reset buttons on the exterior of the machine. Thanks!


... Pressure Washers

11 hp honda motor on landa cold water pressure washer runs good except when trying to pressure wash the motor & pressure go up & down pulsating bbruummmmmbbbbrrruummmmbbbrruuummmmwhats the problem and how to fix it?


... Honda Landa PG 3500 PSI Pressure Washer

I bought a RAC HP132 pressure washer new used it for half an hour and the rubber washer has dissolved in the patio noozle so have changed the washer and now no pressure coming through and no detergent


... Pressure Washers

Power washer I have a karcher power washer and it haves a 7.0 robin motor on it... When i start it up the motor just goes in to high speed... I looked to see if all the springs are on the arm and they are ....All i can think of that the governer on the motor is not kicking it back... If you could help that will be great....Thanks Jerry


... Karcher 2500 PSI Pressure Washer

I have a DeVilbiss pressure washer, Serial# 2251136878, Model# WVRH2421, Radial Pump# D28703, with a 5.5hp honda motor. It has no pressure. If the pump can't be fixed, is there another brand of pump that will fit this model pressure washer?


THE PUMP FITS THE MOTOR and the pump i always use is a ROYALPUMP made in Italy and they are long lasting and easily serviced ,any of the Italian pumps are good ... Pressure Washers

Water pressure? I read somewhere that low pressure of the incoming water will make it so that the items on the top drawer will not be as clean. I don't see how this can be the case, as I thought that the way the washer worked was that the washer filled (at whatever speed) and then the machine itself pumped the water through the system at the appropriate pressure. Please clarify.


Mom...not true. The water fills the machine which then uses its own pump to spray the dishes with the water/detergent. If your dishes are not getting clean, use the recommended amount of detergent. Hard water will require a spot treatment like Jet ... KitchenAid KUDR01TJ Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1034 seconds