Having problems with your Candy 24 in. CD622 Free-standing Dishwasher ?

Timer works and stops ;i.e.stuck on one position to long ,i have to advance it manually

\015 After turning it a little it works a little for at least 45sec then stop again i then have to turn it a little again for it to start dialing again or move on its own.\015

Answers :

Repair Help & Product Troubleshooting for Candy 24 in. CD622 Free-standing Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Timer works and stops ;i.e.stuck on one position to long ,i have to advance it manually


... Candy 24 in. CD622 Free-standing Dishwasher

Hello, my Hoover D7610 dishwasher has developed a problem, I would appreciate your advice.On starting a wash it appears to be working OK through what I believe to be a rinse cycle but then after about 20 minutes water pours out from the bottom of the door. Manually clicking the timer-programer forward stops the leaking but the machine needs manual advancement except for the last 2 cycles when the timer seems to work OK. After the 1st cycle there is no more water leaking from the machine but all


... Hoover Dishwashers

Dishwasher stalls I have a Bosch dishwasher model # SHU4006UC/U06. The dial stops after going through one cycle and the dishwasher continues to run that cycle and will not advance unless we manually advance the dial. After advancing the dial the dishwasher will stall until we have manually advanced the dial until reaching the "9 o'clock" position. It will then continue until the dry cycle is complete. Thanks!! I have the same problem. I took out the timer control and spraid it with contact clean


If the cycle doesn't complete, check these:Water-heating cycle ... Bosch SHU4006 Dishwasher

Hotpoint df32 my df32 stops working during its water intake The water intakes come in 3 10 to 20 second pumpings.Its always after the second .spurt that it stops. In order to start it working again,sometimes a quick on/off of the main jkitchen water tap will start it, otherwise I have to advance the timer manually


REPLACE WATER INLET SOLENOID ON WASHER ... Hotpoint 24 in. DWF32P Free-standing Dishwasher

Dishwasher has very very long run cycle. Dishes come out hot so I'm assuming the water is heated enough, & T stat tests ok. Seems if we advance timer manually it will finish otherwise seems to stay about in the center position on timer.


... Bosch SHU3036UC Dishwasher

Dishwasher stalls I have a Bosch dishwasher model # SHU4006UC/U06. The dial stops after going through one cycle and the dishwasher continues to run that cycle and will not advance unless we manually advance the dial. After advancing the dial the dishwasher will stall until we have manually advanced the dial until reaching the "9 o'clock" position. It will then continue until the dry cycle is complete. Thanks!!


The Timer might not be bad. If one of the two thermostats is bad, the Dishwasher will exibit the same symptom. The thermostats are 141 deg. F and 161 deg F.They only cost $20 each. The Control Module is close to $200. ... Bosch SHU4006 Dishwasher

GSD500X-73WB Dishwasher: Automatic timer has stopped working. It is still possible, though, to work the dishwasher manually by turning the dial. How much will it cost to replace the timer? I guess that it is the whole control unit including the timer that would need replacing.


... GE 24 in. GSD500X Built-in Dishwasher

I have a 1999 bosch SHU 4300 dishwasher given to me. It worked great for about two weeks. Now it takes for ever *3-4 hours* to complete a cycle (if it does). I have opened the door to see it filled with sudsy soap after this long. I have checked the hoses and they are not kinked. Once the cycle of cleaning is over, If I reset it manually, it will rinse the dishes and empty just fine. But I have to manually get the dishwasher to advance to the rinse and dry cycle every time now.


Hi, \012I have an older dishwasher also and recently mywife also complained about it not cleaning right... so me being the man I amtried in vain to clean the things... Bought new spray arms online and installedthem in minutes...now the thing works li ... Bosch 24 in. SHU43 Built-in Dishwasher

I have a GE Profile dishwasher that stopped working after being unplugged for about 24 hours. Now only the timer lights up and no buttons work. Do I need to reset something after being unplugged so long?


... GE 24 in. Profile PDW9880JSS Built-in Dishwasher

Stopped mid cycle with dirty water left on the bottom. cleaned filter and it worked fine, twice. This time it stopped and i can't get the power on. just moved in, with existing washer and have no manual. thanks in advance.


Hi,Here is a tip that I wrote that will help you with your dishwasher not draining problem...Dishwasher Problems - ... Bosch SHU5316UC Dishwasher

The washer cycle stopped without warning, i thought the timer or the timer motor but it is not the timer works fine and so is the motor. but the timer motor runs til the washer motor starts than is the timer stops and the washer is working but not cycling so no rince or drain or soap etc... just pumping water. if you can tell me what might be the problem, thank you. like i said the timer stops when the washer motor start.


... Jackson JPX-300L Dishwasher

Washing machine stopped after wash cycle would not advance to rinse cycle. Tried all the cyclyes manually and it only makes a humming noise from the top part of the machine by the timer.


Could be a bad water valve. ... Kenmore Series 80 Creme Top Panel

Asko Dishwasher starts the cycle by pumping out as it should. But does not stop pumping nor advances. If I click it forward manually it starts to fill and then before overfilling goes into pump out without washing then just repeats this. Pressure switch tubes and air trap chambers are clean and no leak to trip spill switch. I'm guessing It is either the timer or faulty pressure switch any clues ???


If has "mother board" then water could have got in.\015\012\015\012Here Asko is low cost make so check cost before serviceman calls & charges & charges and so on. ... Asko D1706 Built-in Dishwasher

GE Mod # GSD22360Z04WW will not drain water. I manually pushed the solenoid down and the pump and motor seemed to run. No water pumped out of the hose that was disconnected from the garbage disposer. I have discovered that the plug for the disposer was not taken out where the dishwasher hose attached. The dish washer stopped working after a new disposer was installed. I rotated the control knob and at no time did the solenoid for the pump operate. It went back to normal position after control kn


... Dishwashers

I have an avanti dw 18 dishwasher . the problem i am having is the when i turn the on button on the motor goes on however no water fills up. The motor is only humming. But; when i press down the float from inside the machine the water fills up and the machine starts to work. after the water drains again the motor continues to run and hum and the dial does not move. when i manually move the dial nothing seems to change . the motor continues to only hum. Even when the dial is in the stop position


... Avanti Dishwashers

Bosch SHU4302 WITH REPAIRED PC BOARD has been working fine for several years now seems stuck in rinse/drain mode and is not quite pumping cabinet dry. I have removed the screens and located the small impeller at bottom below cover. The impeller rotates as though it has multiple spring loaded stop positions. When I turn on the unit and open the door water is trickling from the sprayer arms at low pressure. It seems stuck in rinse mode and will not advance cycles or reset when shut off.


... Bosch Dishwashers

I have an 8 year-old Kenmore 665.16912 dishwasher. Worked fine until two days ago. Then it stopped working altogether: nothing lights up on the front panel. I have checked the 120 in the electrical box, the door switch is working, the thermal fuse is working and there is 120 volts at the white and black connections to the timer control board. I bought a new timer control board for $120 and that did not fix the problem. What else could be causing the unit to completely stop working?


If all are really good then the only thing it con be is the display (8269205) $25.00 part, if it's bad dishwasher wont run ... Kenmore 16912 Built-in Dishwasher

We have a hotpoint aqaurius dishwasher df23n. When put on wash 4, the timer stops half way through and has to be helped. When the programme then continues through the rinse cycle, it stops half way through. I have tested the water heater and thermostat electrically and they seem ok. Is there anyting else that stops the timer at these positions? The timer knob is free to turn and is not jamming? Steve B


... Hotpoint Dishwashers

Beko d3422 Dishwasher not working, timer does not turn, works if manuall turned. Replaced timer but still same issue.


... Beko Dishwashers

Candy washing machine runs through programme and stops at the point where it drains the drum to start the spin. Have switched it off and turned timer to correct position and it drains and spins OK (1200 spin) Tried other programmes on timer but same thing, stopping at point where the pump drains and the spin starts. Have checked the pump and is OK any ideas please, I am quite capable of taking the machine apart for repair. Thanks in anticipation Pete


... Dishwashers

My Hotpoint diswasher suddenly stopped working last night. It seems like it has no power to it, as the motor or pump does not seem to come on at all. Obviously when I get home from work, I will check the obvious first - making sure it has power to it, connections are secure etc. (I had a wire break before) If it does have power, I would assume checking the door switch and timer is next. Any suggestions, and any suggestions for checking the door switch and timer??


Sounds like your on the right track. I would use an ohmeter to check the resistance of the door switch by placing the meter probes on each side of the switch. Test while opened and closed position. Same with timer ... Hotpoint Dishwashers

I have a Candy CS 455M slimline dishwasher which is 3 years old. The program button has stopped moving round I put dishwasher on and went to work and it was still washing the dishes when I got home from work 8 hours later. I thought it might have stuck and been a one off but no it happens every time is it the timer? is a new timer easy to fit?


... Candy 17 in. CS455 Built-in Dishwasher

Whirlpool dishwasher The dishwasher works off and on. Every few days it stops going on altogether...only the cancel button goes on and the the dishwasher's timer says 2 minutes. Sometimes the air dry button works,but none of the other buttons work. The problem has been when the repair person comes out, it all of a sudden starts to work and so he can't diagnose the problem. I spoke with someone who said it sounds like with the touch pad or computer control board is bad. You don't seem to list my


THE TECH WHO CAME TO FIX MY DISHWASHER FROM Y=THIS EXACT PROBLEM TOLD ME THAT IT IS CAUSED BY THE WATER THAT TAKES TOO MUCH TIME TO GET WARM, SO YOU HAVE TO MAKE SURE THE WATER IS NOT GOING TO BE COLD BEFORE YOU TURN THE DISHWASHER ON. AS TO FIXING I ... Whirlpool 24 in. DU1100XTP Built-in Dishwasher

Whirlpool dishwasher The dishwasher works off and on. Every few days it stops going on altogether...only the cancel button goes on and the the dishwasher's timer says 2 minutes. Sometimes the air dry button works,but none of the other buttons work. The problem has been when the repair person comes out, it all of a sudden starts to work and so he can't diagnose the problem. I spoke with someone who said it sounds like with the touch pad or computer control board is bad. You don't seem to list my


Hi there,\015\012\015\012your problem is intermittent and before you start replacing parts, i would recommend that you do these checks:\015\012\015\012unplug the dishwasher from the wall\015\012check the connection betwe ... Dishwashers

Maytag Dishwasher Model MDB4100AWQ When I start the Light Wash Cycle: Washer fills with water, heater comes on (I checked it with a volt meter--120 volts), timer runs, motor never runs, before the timer gets to "rinse" the heating delay light on the door comes on and the timer stops. The heater is still on (120volts) nothing further happens it just boils away on the water in the washer. Note: If I manually forward the timer to "rinse" the motor will kick in and run but does not pump out w


Most common d/w power is 120 volts, check for 120 volts with a  ... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1476 seconds