Having problems with your Candy 24 in. CD623 Free-standing Dishwasher ?

My candy aquaviva cd 623 runs the full cycle but does not heat up,the elements are fine,is there an overheat stat in line or is the problem with the programme control dial regards gary


Answers :

Hi.

If the machine does not heat up, then rather then the element, the most common reason for no heat is a faulty thermostat.

The thermostat can be tested removing it from appliance and reading Ohms at its terminals, or jumping it and running a controlled cycle (the element will overheat in this conditions and cycle must be stopped manually).

To test continuity (read Ohms), set the multimeter to impedance. With the multimeter probes touch the contacts of the thermostat. If the thermostat is good it will read zero or low impedance. If it is bad, then it will have no continuity (circuit open and Ohms infinity, same as in the air).

The element is tested in a similar way. If the element has no continuity, then it is gone.

The timer board is the last part to be tested and replaced. Thermostat and element must be tested first. Before eventually going for the control module, also test wiring to heating system.

Regards.

Ginko.
Repair Help & Product Troubleshooting for Candy 24 in. CD623 Free-standing Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My candy aquaviva cd 623 runs the full cycle but does not heat up,the elements are fine,is there an overheat stat in line or is the problem with the programme control dial regards gary


Hi.If the machine does not heat up, then rather then the element, the most common reason for no heat is a faulty thermostat.The thermostat can be tested removing it from appliance and reading Ohms at its terminals, or jumping ... Candy 24 in. CD623 Free-standing Dishwasher

Dw doesnt heat up-elements are fine so the fault is between there and the programmer-is there a relay or overheat stat in line?


... Candy 24 in. CD950 Free-standing Dishwasher

Dishwasher stalls I have a Bosch dishwasher model # SHU4006UC/U06. The dial stops after going through one cycle and the dishwasher continues to run that cycle and will not advance unless we manually advance the dial. After advancing the dial the dishwasher will stall until we have manually advanced the dial until reaching the "9 o'clock" position. It will then continue until the dry cycle is complete. Thanks!! I have the same problem. I took out the timer control and spraid it with contact clean


If the cycle doesn't complete, check these:Water-heating cycle ... Bosch SHU4006 Dishwasher

Hello, I've been working on a Bosch Dishwasher. It has no display of any kind, and there's a strange grunting sound coming from the wash motor when power is applied (like if you had just plugged it in), as if it's trying to start. The junction box is getting 120V, all connections to the junction box are fine, and the display board and the main control board are all getting the proper voltage. Now, we've already replaced the main control board and the problem persists. The tech line suggested


... Bosch 24 in. SHE43C05UC Stainless Steel Free-Standing Dishwasher

Hi my nearly 9yr old neff S5555 integrated dishwasher has problems on the control panel the program times come up with the completely the wrong times for the wash ie the 150 one comes up saying 32minutes on a quick wash it gets stuck at 1 minute left and keeps going on, also the delay timer timer is not working ( I have been told this could be a problem with the programmer) . Is it cost effective to get the progammer changed plus engineers cost or shall l look for a new dishwasher? Thanks Su


... Dishwashers

Matsui MF160 integrated dishwasher: Had problems for a while now with the buttons on the control panel ie: on button needed to be pressed down hard for it to connect and sometimes the wash cycle programme buttons would just keep flashing between the three of them and then they would settle down, for the past few days the on button light has stayed on and wont go off and now all the lights on the control panel have gone off and the dishwasher wont work at all, we have tried dis-connecting it, che


... Dishwashers

Recently we had a powersurge after a powercut, and since my whirlpool dishwasher does not react to the start button anymore, the controller board has already been replaced, but the problem remains the same other control knobs like programme selection are still working.


Hi\015\012\015\012Is it showing any error code? Notice if the lights are blinking in any particular order. Try turning it off and plugging it back after 2 min.s ... Whirlpool GU2455XTS Built-in Dishwasher

'Dead' DU1100XTP The dishwasher will not start - no lights at all - no indication that anything's working (although I confirmed the unit has power). I've seen numerous posts regarding the control board - is there a problem with these in general? My unit is just beyond the warranty (naturally!) so I'd like to know if there's been any concession made by the manufacturer due to the number of problems. I'd gladly replace the board if Whirlpool would send me one. Thanks.


This may sound simple but... make sure its plugged in all the way. ... Whirlpool 24 in. DU1100XTPS Built-in Dishwasher

The top drawer of my fisher paykel dishwasher stops during the cycle and shows an icon of a tap with a line threw it (assume that means no or low water pressure). the bottom works fine so I assume water pressure is not the issue; is there a sensor that could be bad? Also, I did switch the controllers between drawers (good instructions on the fisherpaykelparts.net website) but the problem stayed with the drawer, ruling out the controller.


Did it fill with water? could be 1 of your water valves is faulty, or the little filter for the inlet water is blocked. please reply 4 more help. i"m sure i can fix this problem for you. good luck. ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

I have a Hotpoint Slimline 7801 and am looking for an explanation of the programmes it offers. The programmes 1, 2, and 3 are explained, but not all the symbols on the left-hand control. A manual would be helpful. Is one available on line?


The manual is available at this site - but cannot see any more programs but 1,2 ,3. \015\012\015\012 ... Dishwashers

Hi my nearly 9yr old neff S5555XOGB/40 integrated dishwasher has problems on the control panel the program times come up with the completely the wrong times for the wash ie the 150 one comes up saying 32minutes on a quick wash it gets stuck at 1 minute left and keeps going on, also the delay timer timer is not working ( I have been told this could be a problem with the programmer) . Is it cost effective to get the progammer changed plus engineers cost or shall l look for a new dishwasher? Th


... Neff 24 in. S5543X2 Built-in Dishwasher

1)My Candy DFI 50 is not washing properly, it leaves residue on the pots. 2)The programme controller on my DFI 50 seems to be sticking. Sometimes the dial doesn't move at all or takes 'hours' to run a programme. Thanks


Hi,The scum, film and white residueproblems have started since the reductionof phosphates in dishwasher detergents.Here is a tip that will help you to solve the problem of films, residue, and scum in your dish ... Candy DFI Plan Built-In Dishwasher

Hello, I have a washing mashine (BOSCH MAXX WFL 2860), just a few years old. Right now it wont start the centrifuge at the end of the programme, it will just deliver a strange, low grinding sound. Is this something that can be fixed? A common problem maybe with a common fix? regards, Thomas


... Bosch Dishwashers

Problem I think started with pump making noise,now no power to front control panel everything is dead regards


Hi\015\012\015\012The\015\012issue seems to be with clogged/blocked drain pump assembly. First, check the\015\012drain hose for any visible clogging, remove if present. If it's still not\015\012visible then the drain filter or ... Dishwashers

Bosch SHU43C My Bosch SHU43C is stuck with the drain pump running. I ran the self-test and it gave me the fault code 4 wich indicates a filling fault. The washer is empty and all wash cycles display the correct number of minutes for the cycle. It counts down to 0, but the pump continues to run. Does this indicate a stuck float, or is the problem with the control board? Where is the float located? Are diagrams/pictures available on-line anywhere? I've done some searching, but haven't found any. R


My SHU43C is just over 3 years old. I had a similar problem recently. First, there were a few floods. Then, the Bosch only drained non-stop. Even when I used the Cancel Drain buttons the drain pump would run without stopping. When I ... Bosch 24 in. SHU43 Built-in Dishwasher

Dishwasher won't drain; no problems with drain line. Could it be the control board, a relay or the the pump motor?


... Bosch SHX55M02UC Built-in Dishwasher

Dear sir, I have very old Gorenje dishwasher type PMS 201.Recently I have changed programmator with new one but problem is the same.When I put knob on 1 and 2 machine is working ok but if I turn the knob to 3 it does not receive water. I have checked both solenoids and theay are ok.Where to look for the problem.Thanks and best regards Nino


... Dishwashers

Bosch SHX46A (6 years old) Selected regular cycle, pressed On and closed door. Cycle did not start normally. Pump runs, but no water is coming into the DW. I confirmed the water supply line is turned on. I opened door, turned off On/Off switch, then poured water into drain. Then turned On/Off switch on. DW began pumping water OUT of the DW. Also, it doesn't matter if the door is open or closed - if you turn the DW on, the pump will run. I suspect a problem with the electrical controls, or perha


From your description, I doubt that the problem is door latch is the cause.\015\012\015\012The first thing that a modern dishwasher does before it begins to fill with water is run the drain pump.  It appears that this DW is not progressing ... Bosch Integra® 500 SHX46A0 Dishwasher

I have a GU1500XTLB1, type-575-0 Whirlpool Gold dishwasher. For the last couple of weeks I've been getting the control lock on. I got the manual out, I hold the air dry button and it clears. My problem is now when I turn the machine on dosen't matter which cycle I hit (pots and pans, normal, or quick wash) it runs for about 5 minutes and it goes into a mode with the timer having lines going horizontal with the air dry button lit up and rinse button lit up. It sounds like it starts the cycle


Hi,There are Few Tricks to Reset this. Follow the below Tricks :-1. Try holding down heated dry key for 5 secs. I believe that is the control lock/unlock button on your model. IF not, look for the lock symbol and follow same i ... Whirlpool Dishwashers

Hi I have a Miele Premier Dishwasher and the detergent compartment does not open during a wash cycle. Mechanically it all looks okay. Is it likely to be a problem with the programme controller?? or something else?? Thanks


Why buy this junk? ... Miele Dishwashers

Baumatic dishwasher We loaded up and switched on as normal but we had all the programme lights flash on and it does not seam to load up with water, We checked the filter inside and found it very blocked, after emptying it it still has the same problem. kind regards: Mark


Baumatic dish washer bdf64ss\015\012will not drain and code 8 shows ... Baumatic 24 in. BFD60SS Free-standing Dishwasher

Hi I have a Candy cd242 dishwasher all of a sudden it has stopped washing, I found that the feed hose had a kink in it so have re- routed that. But now the timer appears to go around but only part runs each section of the programmes, and then just ticks the rest of the time. Does any one know the problem or could it be a over filling valve that has sent a message to the controller. If so how do I re-set that. I would appreciate any-ones help to [email protected] cheers simon


... Candy Dishwashers

Hi I have a siemens hi line, the door was forced closed and it is not working properly since, the motor is still running and the programmer are still working, so would replacing the catch fix the problem?


... Siemens 24 in. SE25A836GB Hi-Line Free-standing Dishwasher

I have a Braun combimax 650--it is fairly new. It was working fine last time I used it, but this time, the dial that turns the machine on seems to be stuck. The little button for the pulse does work. I read the instructions, which said that this might happen when the machine overheats and to wait fifteen minutes, but it is definitely not an overheating problem and the last time I used it was weeks ago.I love this machine and now need to use it for quite a number of things--any help you can provi


... Braun K-650 CombiMax Foofs Processor FOR 110 VOLTS

Pld2560lcc1 Dishwasher...Control Panel shows 65 minutes left on lower rack, works for about 1 minute, shuts down. None of the buttons work. I changed the control (major circuit) board, same problem. I wonder if it's the control "panel"? I took that off and looked at it. Seems okay, but could the problem. I've heard this model has control problems, but I'm not sure if they mean the major control board or the control panel that has the buttons.


Pulled the touch pad, go after the middle third with a very small screw driver, cleaned the flex circut with contact cleaner\015\012\015\012powered up fine seems to be working again ... Frigidaire 24 in. PLD2560LCC Energy Star® Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1177 seconds