Having problems with your Candy 24 in. CD623 Free-standing Dishwasher ?

Model CD623 uk.In all programmes the timer runs to allow water in,then starts to wash. Mc, just stays in the wash mode and timer does not move on. The water remains cold.. Fitted new timer Pt No 41002535 but problem not solved.


Answers :

Hello Bill,
\015\012
\015\012You mostly answered your own question already. Yes, the cold water is related to the problem. If the water doesn't heat the programme will not advance and the timer will appear to be stuck - there is no fault with the timer. You should be investigating the heating element, the thermostat and, if those check out, the relay on the control module for the heating circuit.
\015\012
\015\012The control module gets a signal from the water temperature sensor to determine when to advance the wash program to the next stage of the cycle. If the water doesn't reach the desired temperature, the washer keeps running the current stage of the wash cycle until this temperature is reached. If the water doesn't heat, the control module never gets this signal from the sensor and, therefore, it will never advance. This gives the impression that the timer is stuck. The "timer" isn't actually a timer, it's simply a digital time display. The timing is really done by the control module.
\015\012
\015\012You need to test your heating element for resistance/continuity before you do anything else. I strongly suspect that you will find it to be open-circuit, i.e. burnt-out. If that proves to be OK, check the thermostat next. It should be closed-circuit when the washer is idle.
\015\012
\015\012Assuming you have a multi-meter or can borrow one and you know how to use it, I suggest you check the heating element first. Please make sure the dishwasher is disconnected from the power supply before any electrical testing. If you are not competent or confident with electrics or electrical safety, I would advise you to seek professional assistance.
\015\012
\015\012Hope this helps - please let me know if you need further assistance.
\015\012
\015\012Regards,
\015\012BElectric

\015\012

Hi
\015\012\015\012

As you have already replaced the timer then it means the\015\012issue is with the unit not draining properly. First clean the drain hose and\015\012the drain pump for any clogs, you can do this by taking off the bottom access\015\012panel. Hope this helps...please post back for further assistance.
\015\012\015\012

Daniel

Repair Help & Product Troubleshooting for Candy 24 in. CD623 Free-standing Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Model CD623 uk.In all programmes the timer runs to allow water in,then starts to wash. Mc, just stays in the wash mode and timer does not move on. The water remains cold.. Fitted new timer Pt No 41002535 but problem not solved.


Hello Bill,\015\012\015\012You mostly answered your own question already. Yes, the cold water is related to the problem. If the water doesn't heat the programme will not advance and the timer will appear to be stuck - there is no fault wi ... Candy 24 in. CD623 Free-standing Dishwasher

EDW5500DSS wont completely drain water Okay so now that my dishwasher runs, when it finishes a cycle it has a nice puddle of water at the bottom that never drains completely out. I am assuming its a relay or something because I looked for a floating switch (did not find), I can hear a pump sound as if it wants to pump the remaining water out, but, it doesn't. I really want to solve this problem soon so I can order the new door seal and needed part together. Checked the line out and of course i


The srainer over the pump could be clogged not letting the water drain quick enough. Be sure the screen is cleane out. I believe you would have already checked and cleaned this. I believe it is the impeller on the pump that pumps the water that is ei ... Dishwashers

Dishwashing machine not fully draining (2 inches of water remain). I have an open problem concerning this problem. I have a new pump. dishwashing machine not fully draining (2 inches of water remain) For this machine.


Following a cycle, a small pool of clean water inside the tub is\015\012typical. Excessive water means the pump isn't pumping water out\015\012properly, the drain hose isn't carrying it to the drain pipe, or the\015\012house's drain lines are backed ... GE 24 in. GLD5860LSS Stainless Still Built-in Dishwasher

Miele 868 dishwasher-water fills at begin of cycle,but pump/wash cycle doesn't engage(timer dial still advances,drains at end of cycle.dishwasher was workong,but was moved to a new location ans hasn't worked since.impeller moves freely and pump was rotated via 8mm hex key.is there possibly a reboot/reset, or is there possibly a water pressure issue?-I didn't think so as the dishwasher fills to the prescribed level.


... Miele Dishwashers

Water stopped pumping so ordered new pump. Upon removing the old I discovered it had a few straws twisted up into the pump. Removed and reinstalled pump and it sounds great and throws water all over with force. PROBLEM: Now there is ZERO water coming through top tube to spray arm. Pulled pump back off and noticed what seems to be a "white diverter ball" that moves a little in front of the inlet for the upper water tube. Any guidance to where the ball should be prior to installing the pump or i


... Kenmore 15529 Built-in Dishwasher

I also have a dishwasher (AEG Favorit), and it does not heat the water anymore. It worked fine for last 3 years, and all sudden, it only washes dishes with cold water. Could you please help to solve this problem? The hot water line is fine and I do have the hot water to the sink next to the dishwasher. Thank you in advance for your help.


... AEG 23 in. Favorit 44070IW Built-in Dishwasher

Water stopped pumping so ordered new pump. Upon removing the old I discovered it had a few straws twisted up into the pump. Removed and reinstalled pump and it sounds great and throws water all over with force. PROBLEM: Now there is ZERO water coming through top tube to spray arm. Pulled pump back off and noticed what seems to be a "white diverter ball" that moves a little in front of the inlet for the upper water tube. Any guidance to where the ball should be prior to installing the pump


... Kenmore 15529 Built-in Dishwasher

Kenmore dishwasher. The upper rack is not getting clean. Even very light residue remains. And, detergent is left in door at end of cycle. The bottom is filling up, so I don't think it's the intake valve. Also, all the blade openings appear clear. I am noticing that hot water is not filling the dishwasher when I first run the cycle. Even if I have hot water running in the sink, the dishwasher fills with cold or warm water. So, I think this is the problem. What should I do? Thank you in advance!


I find it odd that the dishwasher is filling with cold water if the water is hot at the sink. It sounds like the dishwasher is connected to the cold water line rather than the hot. Check under your sink; if you've got standard plumbing, the dishwas ... Dishwashers

When i switch the dishwasher on it pumps out the remaining water as per usual but then fails to let in new water. what could be the problem. i have checked the filters, water supply and pipes. all are ok.


Little complex for quick diagnosis. Firstly., does water try and come in for a short period or not? If it does, then your electronic water pulsator(counter) is faulty. Needs replacement. If no water comes in at all, you either have a leak in the ... LG 24 in. LD-12BS6 Stainless Steel Free-standing Dishwasher

ADP6000WH/ADP6000IX--Whirlpool Dishwasher.(new) My problem--Water not getting hot--i have it connected to the cold water--should it heat the water ?


Error 3 not heating..on wix6000 /or / ADP6000WHsame boards .rip out the the main mother board ... Whirlpool Dishwashers

Machine does not heat up. The water remains cold and the cycle takes hours irrespective of the setting temp. Heater seems to be OK and a tech guy repleced the sensor today as he thought that was the problem after everything else seemed to checkout ok but still no go. It has already cost us 200 dollars and I dont want to keep spending money having tech guys guessing the problem. Any suggestions? Thanks


Depending on the model, I have had loads of Bosch dishwashers fail because they have blown the heater relay solder joint on the main control board. Usually just requires control board to be opened up, and the faulty solder joint re-soldered. Occasion ... Bosch Dishwashers

DWI612C wash cycle runs on and on and on. Believing to be a problem with water heating I tried putting a couple large pan fulls of boiling water into machine during wash cycle and this did move it on from wash to rinse. How do I replace the heating element I cant see it it is not in the dish washing compartment? I dont want to call out a repair agent as one can probably buy a new machine for what that will cost. Thank you.


... Smeg 24 in. DWI612 Built-in Dishwasher

There's a foul smell coming from the dishwasher evert time I open it. Doing a wash does not solve this. I'v had this since it was new, months ago, and have had the installer look at it, said it wasn't his problem. Had a tech. come in and said it wasn't his problem. I've owned many dishwashers and never has it had a foul smell. Last fall I went to Nova Scotia, ran the dishwasher before I left, came back in two weeks and noticied water was still in the bottom of the dishwasher-it didn't drain all


... Frigidaire FGHD2433K 24 in Builtin Dishwasher

New hoover HED 6612-80 dishwasher all indicator lights staying on, manual says due to overfilling with water which is confirmed by water leaking on to floor, how do i solve this problem


Hi, i have same problem with my hoover dishwasher same model as your own, did you ever find out how to fix the problem. your help would be really welcomed. thanks lesley ... Hoover Dishwashers

Our GE dishwasher (5 yrs old, Model GLD4250L00CS) only fills with water half way when the unit is started. The inlet valve was replaced with a new one, but that did not solve the problem. When started, the dishwasher fill cycle runs for 41 seconds before the wash cycle begins. Repair workers told us we probably need a new ECU (Electronic Computer Unit). My questions are: Is 41 seconds the correct time for the fill cycle for our model? What else could be the reason for the unit not filling pr


Hello &\015\012Welcome to FixYa\015\012\015\012Check this\015\012 ... Dishwashers

Have installed a new heating element into the idw604 dishwaster - but now an (E4- overfilled)problem has occured possible cause "too much inlet water" any suggestion on how to solve this problem ?


Replace water valae ... Belling 24 in. IDW603 Built-in Dishwasher

Both spray arms of my DU943PWKQ0 do not turn or spray. The motor is moving and the it drains without problem. During the wash and rinse cycle I can hear the sound of water, however it doesn't clean at all and the sprays arms stay where they were. It seems the motor only creates no spray, but wave. I powered cycled the dishwasher, the problem remains the same. Anyone know what's wrong with it? Thanks James


Try rotating the spray arms by hand. It should rotate freely. If possible clean the arm rotating place by removing them.Arms rotate by by pump pressure only. finally check the water pump also. ... Whirlpool DU943PWK - Multiple Color Built-in Dishwasher

Wife put washing up liquid into the machine and let it run it was full of bubbles and now it wont heat the water think the element is gone but the timer wont move past the heating stage if i replace the element will that sort the problem or will i have to get a timer as well?


If you put manual detergent that hapend, it could burnd electronis card (or mechanical timer-programer blowup), thermostat or the presostat, the heating element must be OK. ... Dishwashers

Hotpoint Dishwasher I recently moved in a new place. I am assuming there was a dishwasher here beore because there was a space for it.It is now connected with electricity but no water is coming in. It worked pertectly before the move. It is 2 years old. What can I do to solve the porblem.


Mate, apologies if this a stupid reply but its an easy thing to miss, i had a similar problem in my old place it turned out there was 2 check valves on the dishwasher supply both had been turned off, i assumed that the one that was visible was the on ... Hotpoint 24 in. FDW60 Free-standing Dishwasher

Water remains in the bottom of the diswasher after the cleaning cycle has completed. We recently had a new kitchen faucet and garbage disposal installed. The dishwasher also hums during the dry cycle, I never noticed this before. Are these problems related? Do I need to get a repairman out here to fix the problem or can I do it myself? Thanks, Robin Pomazal Naperville, IL


... Maytag MDB7609AWS Builtin Dishwasher

Hi, We have a new whirlpool dishwasher type no. 575-0. GU2275X TVQO. We have not been able to get clean dishes since purchase. Water is hot, everything seems to be operating smoothly. Use the supplied rinse product. Sometimes the dishes remain dirty, always have white film on clear glasses. We have tried using more or less detergent. Our water is a little hard, but should not be that big of a problem? Please advise joe


I think I can help. We have the same dishwasher and we have very hard water. The dry powder detergents don't work well. We have found Cascade All in One Gel detergent works best and we use only a little; don't go beyond the first mark in the detergen ... Dishwashers

Model #363.15161792 will not operate even after installing a new WD21X10013 timer. Timer moves, pump starts, but no water comes in to wash. The pump does continue to run. Now what?


... Kenmore Dishwashers

My GE dishwasher timer gets stuck and doesn't move. I replaced the solenoid already as the water wouldn't drain. Would replacing the timer fix the problem for good?


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks\015\012for using FixYa. Timers usually won’t go bad however,\015\012if every other part of the dishwasher seems to b ... Dishwashers

Ther's a foul smell coming from the dishwasher evert time I open it. Doing a wash does not solve this. I'v had this since it was new, months ago, and have had the installer look at it, said it wasn't his problem. Had a tech. come in and said it wasn't his problem. I've owned many dishwashers and never has it had a foul smell. Last fall I went to Nova Scotia, ran the dishwasher before I left, came back in two weeks and noticied water was still in the bottom of the dishwasher-it didn't drain all t


... Frigidaire FGHD2433K 24 in Builtin Dishwasher

No power going to the water valve or the pump - the only thing working is the motor did replace the timer but didnot solve the problem checked all relays switches what wrong


The water-inlet valve lets water enter the machine. First Check to see if the valve is getting water. Make sure it's not clogged. There is a screen on the inside of the valve, this sometimes gets clogged up with debris. Check to see if you g ... GE Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1780 seconds