Having problems with your Candy 24 in. CD650 Free-standing Dishwasher ?

I have a Candy CD650 dishwasher which is not washing properly. Basically, the detergent tablets seem to be getting stuck in the tray. Most times I open the door, the tablet is a pile of mush inside the tray. Other times it is on the bottom of the dishwasher - again a pile of mush! Sometimes, it starts the program & sounds like it's about to start a wash cycle, but then gives up! it gives one short woosh, the stops again. Any ideas how to fix this? I don't have a manual so can't look there.


Answers :

Repair Help & Product Troubleshooting for Candy 24 in. CD650 Free-standing Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have a Candy CD650 dishwasher which is not washing properly. Basically, the detergent tablets seem to be getting stuck in the tray. Most times I open the door, the tablet is a pile of mush inside the tray. Other times it is on the bottom of the dishwasher - again a pile of mush! Sometimes, it starts the program & sounds like it's about to start a wash cycle, but then gives up! it gives one short woosh, the stops again. Any ideas how to fix this? I don't have a manual so can't look there.


... Candy 24 in. CD650 Free-standing Dishwasher

I have a Maytag quiet series 400 dishwasher. I set the required buttons for a wash, inserted the soap in the soap tray but the machine will not start. Previously, when the washer would not start, I opened the door and pushed down on the soap tray and its seemed to fix the problem. Next time I used the machine, again not starting, but by pushing on the soap tray it would not start. Can you suggess what the trouble may be or give me a check list that I may do before starting the washer. This machi


... Maytag Dishwashers

I just recently purchased a new fridgidare dishwasher and have tried it four times. the first three times i tried using a tablet and it didn't dissolve at all. this last time i used liquid and it all was piled up by the drain in the front left corner...is there something that i'm doing wrong? or is it a problem with the dishwasher...


Your water is not entering the dishwasher. Could be a kink in your water supply hose or the water supply is not fully on. Perhaps during installation the wires came loose from the water valve underneath.Check these things and report back. ... Frigidaire Dishwashers

My elecrolux dishwasher gives me error code 11. What do I do? I have the manual, which says that it timed out before it could establish a drain... but there is no info on how to fix it. The dishwasher is new, but it has run 6 or 7 times with no problems.


... Electrolux EWDW6505GS Fully Integrated Dishwasher with 9 Wash Cycles, Nylon Racks, Wave-Touch Contro... 24 in. Built-in Dishwasher

The dishwasher cycle starts and gets 20-30 minutes in and then stops giving me the - - - like the door was opened, but it was not. If I use extra heated wash, the cycle stops at 63 minutes left. If I use the regular wash cycle, it stops at 43 minutes left. I have to click the resume button to get the dishwasher to complete the wash cycle. This has been happening evey time I use the dishwasher the last 2 weeks. It is Whirlpool dishwasher model GU2700XTSS! and is only 3.5 years old.


Hello,\015\012\015\012Welcome to FixYa.\015\012\015\012I suspect based on your description...\015\012\015\012"stops giving me the - - - like the door was opened, but it was not, I have to click the res ... Whirlpool Dishwashers

Kenmore dishwasher 16934 will not start up for me. I can push any button to set the cycle(pots & pans, china gentle, quick rinse, normal wash) and the time shows up in the display, but when I push the start, two red horizontal lines appear in the time remaining display. Cannot get the machine to start anything. All cycle buttons give me some kind of time remaining display but as I said, it ends up with 2 red lines. Thanks in advance. Mark


... Kenmore 24 in. 16934 Built-in Dishwasher

Hi there I purchased a Simpson Riviera 966 Dishwasher about 10 years ago and was very happy with it. All of a sudden water was flooding the kitchen from somewhere under the dishwasher, and not having the money to repair it at the time, it has just been sitting, and possibly the seals may need replacing. All electronic funtions seem OK on it however. Would it be possible to give me a quote on repairing the dishwasher - I HATE washing up !!!! My name is Hartley Cowderoy, and I Live at 65 Rosemount


... Dishwashers

Hello everybody, I hope that you gona a give me some tips for repairing my dishwasher mashine. A few days ago, the error F2 appears on my dishwasher machine (Baucknecht GSI 5894) I checked the pump for the waste water is ok. the tap water is not taking in,I checked the hoses they are ok as well I turned off and on and same time pressed the button reset and choosing the programm on the dishwasher few seconds trying to start and again apperas F2 . Hopefully someone can help me. Best regard


Possible the inlet valve has given up and is not allowing water in.\012Also possible there is a slight leak enough to shut the water off (safety feature) - Check underneath for a float mechanism and any water there. ... Bauknecht Dishwashers

Bci450 My dishwasher has been always giving me lots of trouble. It is the BCI450 model from hotpoint. Whenever it reaches the washing stage for steam, it seems to beep alot. Many times they replaced the Circuit board but this problem comes back after 2 months. What could be the reason this is caused? Today they replaced the rubber thinking that water vapour might be reaching the circuit. I got this repaired about 7 times already and each time they replaced the circuit board.


... Hotpoint Dishwashers

When trying to start the dishwasher, pressing the Normal wash button, the dishwasher gives a huge clunk and then it trips the circuit breaker. Upon resetting the breaker, I tried the next button over, which is Soak and Wash, and it seems to go thru the cycle fine. Another time I tried the Normal button, but put the left dial on Rinse and it started up, but it would clunk periodically and it seemed to have a 'hot' smell. I'm worried to use it - what could this be? Is there anything else I can try


Hi\015\012\015\012This is a very dangerous situation you must remove from the wall supply and desist from using, such a fault could easily make the casing "Live" and anyone touching it may be killed. You need to discover why this is happe ... Dishwashers

Further to my open question for my Asko N516 D5131 SS dishwasher I have been able to successfully press the wash setting cycle, which was before frozen on 'rinse and hold' . I then press the on/off. Button the time shows but as soon as I press it to start the dishwasher the screen changes to three horizontal curly lines and nothing further happens... It won't start. Please , I do hope somebody can give me advise. I cannot get to the power plug as it appears pot be located behind the unit whi


... Dishwashers

We have a KitchenAid dishwasher (KUDI01FLSS6) which has not been working properly for a long time. We have the dreaded green blinking light mystery. We understand that this could indicate several different problems. We have found that if we run the sink water until it is hot, then start the dishwasher, and then after ten minutes we open then shut the door, it will consistently run the full cycle perfectly. Does this give you any hint of what might be the problem component -sensor, element, the


... KitchenAid 24 in. KUDI01FLSS Stainless Steel Built-in Dishwasher

Whirlpool dishwasher I have a whirlpool dishwasher model # 665.16519202, and the clean light flashes 7 times then pauses. I was having a problem with the machine working properly right befor the fault code came up and froze it. Can you give me any guidance as to the problem of this washer? Thanks in advance.


If the dishwasher doesn't sense a water temperature increase, it will stop working and lock the functions (clean light flashes 7 times, all buttons are non responsive).To resolve this you will have to reset the console. Do this by closing ... Whirlpool GU2400XTP Built-in Dishwasher

I have a nardi dishwasher and it does not wash the dishes properly. sometimes the water does not circulate.Sometimes there is no water at all. I use the proper finish stuff, dishwash salt, tablets rinse aid. each time I call an engineer out they all give me a different diagnostic. HELP. Please


Nardi dishwaser water will not drain away after wash cycle. ... Dishwashers

Whirlpool APD5550 Dishwasher, cycle does not start, green light on start button flashes 6 times, pauses, flashes 6 times etc. can you please give me some indication what the problem may be. Thanks


... Dishwashers

I have a user guide for my ASCO 1996 dishwasher however when we lose power it loses its settings. I have had a repair guy come out and charge me $100 just to hit the wine glass 5 times and reset. This time the drain cycle is not long enough and I know you can program it to give it a longer drain but I don't know how and these appliances don't come with programing instructions which seems completely stupid to me!!!!!


You will need to call the engineer at your place.as the settings are available with the service center sources only.the engineer that visited your place was either a ASCO  engineer or he has received the service manual  from ASCO techinicia ... Dishwashers

Dishwasher Stinks Our dishwasher has recently begun to smell like burning rubber when it is running. Still washes the dishes fine, and we pulled it out several times but can find no smoking, smoldering, etc to pinpoint the problem area. Fumes give me a headache. Can anyone help?


Is your dishwasher less than a year old? if so you need to call bosch and have all the gaskets replaced. they tried a new chemical to make the gasket but now have found that after the dry cycle the gaskets put off a strange odor like your discribing. ... Bosch 24 in. SHX99A15UC Stainless Steel Dishwasher

Whirlpool dishwasher I have a whirlpool dishwasher model # 665.16519202, and the clean light flashes 7 times then pauses. I was having a problem with the machine working properly right befor the fault code came up and froze it. Can you give me any guidance as to the problem of this washer? Thanks in advance.


Do a "key dance" between normal and heated dry , going bak and forth six times. this will rester the heater fault. That is the clean light flashing code. Now you have to find the cause. Most likely is that there were suds in the last cycle or the do ... Dishwashers

My dishwasher makes a banging noise whenever the water supply shuts off & it drains. It has been doing this for a long time. I finally bought a hammer arrester & soldered it on the line after the tee for tap & dishwasher & it sits about 1 foot up.this did not solve the problem. It still bangs loudly & I'm worried about damaging my pipes since they are old copper pipes. can you give me some advise it is a ge Potscrubber mod. #SSD539PS1181 Dave


... Dishwashers

Sometimes the dishwasher drains, sometimes it doesn't; I emptied the dishwasher, removed the bottom tray and baskets; ran a cycle - it drained so, I presumed it was now operating as it should - it wasn't - the tub was full of water so, I ran a rinse (5 minutes) cycle - it drained next time I ran a cycle - it didn't drain


Hi,Here is a tip that I wrote that will help you with your dishwasher not draining problem...Dishwasher Problems - Water will not drain out ... GE Nautilus 24" Built-in Dishwasher

I have a frigidair dishwasher serial number th73793661 purchased in 07. It continues to wash and rinse but never turns off and no heating unit comes on. I have for some time had wet dishes and even mold in the trays. Is this repairable? mary Anna rushia


Hi\015\012\015\012Your dishwasher is certainly fixable - the issue is troubleshooting to find where the fault lies.\015\012\015\012From your description this can be narrowed down in order to three areas as follows\015\01 ... Frigidaire Dishwashers

How do i get electrolux to give me a new dishwasher given that the old one is a dud and can burn my house down? I don't just want a 'fix' like last time


Unless a tech can condem your unit, and it is less than a year, you will not have much to stand on. Can you discribe a little bit more on what problem the D\\W is giving you. ... Dishwashers

Our Asko 3530 dishwasher is giving us a 'water inlet fault' code. The machine goes through the pre-drain at cycle start then begins to fill, continues until it's full then kicks out the fault code. I have changed the inlet valve, reset the system to factory default and taken off the lower front panel, finding the overflow area to be dry. Is it time to call for service or is there something else to try before spending the big bucks?


Hi,This sounds like either the overflow sensor or the water control valve is stuck.Usually the valve is a solenoid valve that controls the entrance and fill of the water. If the overflow sensor is underneath, there may be wate ... Asko 24 in. D3530FI Built-in Dishwasher

After dishwasher was started, and water stared to enter the machine, it was unlatched and left with the lever in the open position for some time. The control dial had automatically moved 5/6 degrees clockwise and left there. Now the machine does not want to start no matter what I do. Power is to the machine, latch is moved to the right, but nothing happens. What's next. Thanks for any help you can give.


Hi,\015\012 \015\012After the water stops coming in do you hear a humming noise? If so the motor may be stuck. Unlock the door to disconnect power from motor then turn the motor by hand a few times (should ... Dishwashers

I have a GE GSD2000J01WW Dishwasher in a building with low water pressure. The inlet hose is 3/8" OD. The heating coil gets too hot and gives off a bad odor as there is not enough water at start up. Is there a way or a replacement part that can be used to change the timing of the heater and wash cycles, etc.? Thanks


... GE GSD2000J Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1675 seconds