Having problems with your Candy A8001 Dishwasher ?

Is it possible to get replacement upper basket and rotating arm for candyc7400 ecosystem 15 years old but working well


Answers :

Repair Help & Product Troubleshooting for Candy A8001 Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Is it possible to get replacement upper basket and rotating arm for candyc7400 ecosystem 15 years old but working well


... Candy A8001 Dishwasher

I have a Whirlpool Dishwasher DU1345XTVB about 5 years old. It functions perfectly but is not cleaning the dishes well particularly the top rack. The arms spin, soap dispenser works, cycles properly--just doesn't get the food off. I checked the arms to see if the are blocked but don't appear to be as the dishes get wet. Thanks


There are a few things to do. The water temperature is a big contributor, in dishes not getting clean. Another is the type of detergent being used. Liquid dishwasher detergent with water softeners and a drying agent will help loosen food too. If ... Dishwashers

No water The serial number is not my dishwahser, however mine is about 6+ years old and has worked fine, I keep it in fairly good order, cleaning rotar arms weekly and filters as often as needed. Yesterday 4th August the timer which is a dial type, was getting as far as the next section and stopping, also it would seem that no water is being drawn through the arms. Are we near the end of life or is it fixable?????


Check first the filters on the inlet water line.\015\012Then, if problem still exist - check that the inlet water valve works(it is an electromagnet valve, located at the pipe's entrance to the machine)).\015\012If it doesn't work, test that it get ... Neff 24 in. S5409X0 Built-in Dishwasher

Our Maytag MDBH985AWSO dishwasher is 2 years old, and the start button will not work. It just started up on its own and ran an empty cycle 48 hours after our last attempt to get it running. All other buttons appear to be working. Should we replace the control board its like 200$ for the part alone.


... Maytag MDBH985AWW 24 in. Built-in Dishwasher

I have a Frigidaire Dishwasher, model #FDB635rfs It is not that old, but appears to have quit working. It sounds like it runs the water gets pushed in by the tube on the side but goes straight to the bottom of the washer. It looks like the spray arms are not spinning. Water is not circulating. Element still heats up. Detergent just runs down the inside of the door and doesn't dissolve since water is not circulating through arms. I have just replaced the water inlet valve and it did not hel


Don't know about yours but many of the rotating spray-heads are turned only by waterpressure, not a separate motor.\015\012The rotator is normally pretty loose and should turn willingly by hand; if it seems stiff and your water pressure is normally l ... LG LDF6810 Built-in Dishwasher

Dishwasher just started leaving food residue on dishes after washing. We usually don't rinse beforehand but even when we do this it's still happening. Can I run something thru a cycle to give the washer a good clean out? I've cleaned the filter (nothing there), tried to clean the spinning arm as well as I could and looked for any other food that might be clogging things up. Dishwasher came house - think it's about 6-8 years old. Otherwise works great.


Hi,The scum, film and white residue problems have started since the reduction of phosphates in dishwasher detergents.Here is a tip that will help you to solve the problem of films, residue, and scum in your ... GE Nautilus 24" Built-in Dishwasher

I was given a low hour, 10 year old, CH PW205002LE 6.5 HP gas vertical shaft 2000 PSI/2.5 GPM pressure washer with a Lavor pump. It did not work - no pressure. I found a broken o-ring on the brass unloader valve and replaced it with a ring as close in size as I could find as the part break down doesn't state size. Everything was very clean. I coated everything with silicine grease and reassembled, seating the brass piston? as deep as it would go. I had to press the trigger in order to get the mo


My personal experience is that 40% of all the sellers I dealt with on e*** exaggerated their products or worse. If you decide to go the e*** way be sure you put it on a good credit card so you can get your money back if it's a bust. Don't use your ba ... Campbell Hausfeld Pressure Washers

2 year old dishwasher is not cleaning well all of a sudden. Not sure spray arms are working properly but don't know how to test


The arms are easy to remove without tools.\012\012Remove the arms and clean out the jets. ... Dishwashers

My Professional series dishwasher does not work properly. It is only 1.5 years old and glasses on top rack get sprayed with fine layer of particles every time I use it. Other items, top and bottom, are often not clean as well, but glasses are the hardest to re-clean. I have tried evacuating the water left at the bottom of the dishwasher before running, pre-running the hot water in the sink and ensuring that the disposal was run, removing and cleaning the filter at the bottom of the washer. None


Hi, \012 \012I have an older dishwasher also and recently my wife also complained about it not cleaning right... so me being the man I am tried in vain to clean the things... Bought new spray arms onli ... Frigidaire PLD4375RFC Dishwasher

I have a Bosch SGE63E05UC dishwasher that keeps intermittently showing an "E:25" error code. Occasionally it will get all the way through a cycle without going into error, but more often than not it will error and stop. So far the main control module in the front panel and drain pump have been replaced and the problem persists. All hoses have been checked and are clean (unit is only 1 year old) and drains well, when it does drain. Any suggestions?


... Bosch SGE63E05UC 24 in Builtin Dishwasher

Smeg df612sdx Until last week I enjoyed several years faultless service from my SMEG Stainless Steel dishwasher, with the exception of needing to replace 2 x spray arms. The unit has now stopped working altogether. Despite powering up several times, I continue to get both the start/pause and selection programs buttons constantly flash (green lights) when the unit is switched on; previously this only occurred once the wash cycle was complete. Any thoughts would be most appreciated. Thank you


... Dishwashers

Bosch Diswasher Have Bocsh SMU 2046 UC diswasher. Aprox. 11 years old Has always worked well. Recwntly is not cleaning at 100% as before. Seems to run through cycle as normal and sort of cleans but leaves stains in coffee cups and flatware seems filmy, sometimes a little guk left on dishes, all uncharacteristic of past performance. Tried a thermometer during cycle and water temp is around 151 F during wash, 136 F at rince. and 154 F at dry time. Have checked arms for cloging and are free w


Remove the drain hose and check if you have any residual into it. After 11 years your appliance may need a thourought cleaning.Check also if the pump has enough pressure. ... Dishwashers

KUDS30 leaking my kitchenaid dishwasher (about 1 1/2 years old) had a leak bottom left side and had gasket replaced. It worked well for approx another 6-9 months without any leaks and now the same problem is back. The dishwasher isn't overloaded. A repair person came last week and ran the dishwasher empty and it didn't leak when she was here. The 2 loads after continue to leak approx 2 cups of water each cycle.


... KitchenAid 24 in. KUDS25 Built-in Dishwasher

Glasses int he top rack of my kitchenaid dishwasher don;t get clean. they finish the run spotted and covered in what looks like baked on dirty dishwater. dishes in the lower rack look ok, but the silverware is always dirty, too. i figure it's one of two things - either the top sprayer isn't working, or the machines doesn't drain the dirty water well enough. or maybe it's something else - cycle regulator? the machine is about 4 years old. thanks


If you have hard water, glasses can look spotted and cloudy even after cleaning. Sometimes changing the dishwasher detergent can help. The easiest solution to clearing up glasses that start to look cloudy is to add some vinegar to the bo ... KitchenAid 24 in. KUDI01FLSS Stainless Steel Built-in Dishwasher

I HAVE A BUILTIN KITCHENAID SUERA DISHWASHER WHICH IS ABOUT 14 YEARS OLD IT SEEMS TO WORK PRETTY WELL. BUT THE SOAP DISPNSER DORRS TICK CLOSED SO THE DISHWASHER FINISHED AND THE DOORS REMAND CLOSE SO THE ONLY WASHING IS DONE WITH WATER AND NO SOAP. THE SOAR DOOR HAS TWO SLIDING DOOR THAT ARE ARC SHAPPED AND SEEME TO BE CONECTED WITH BUTTONS ATH THE CENTER. THE SOAP DISPENSER ID AHITE INJECTION MOLDED PLASTIC ANDY IDEA I CAN TRY TO GET THEM TO OPEN DURING WASHING CYCLE THANKS **** VON ROTH


Water does not come into the washer ... KitchenAid 24 in. KUDP02CR Built-in Dishwasher

SMEG STX 45- the programme transfer- on the top edge of the door -has washed off over time so it is now impossible to read. any ideas of what to do? maybe a replacement door? the machine is 10 years old but working well. thanks


... Dishwashers

My 2-year-old LG Dishwasher doesn't clean the dishes well any more. It used to work great, I was very happy with it. For some unknown reason it doesn't work that way any more. The dishes come out dirtier then they were before I put them in. I had three guys come in and look at it and they all said that there is nothing wrong with my dishwasher. My water heater is 1 year old, works great everywhere else in the house, the dishwasher is hooked up the right way, by a professional, I don't have hard


The heater does not heat the water it keeps it hot check there first id say the heater or thermal is bad if both check good replace control ... LG LDF6920ST Stainless Steel 24 in. Built-in Dishwasher

My panasonic range microwave NN-S255WF started to randomly beeping and flashing the potato/vegetable setting. For about 15 minutes the microwave keypad would not work at all. It is working again. The range overhead light on the bottom of the unit stopped working about a year ago - light will not turn on. Please tell me what the issue is, what would need to be replaced. The microwave is 4 years old. Thank you!!


We get microwaves in our shop frequently, this unit sounds as if it's brain has been damaged, I suspect, as it usually is that either the magnetron, or the High power Diode, has failed, this usually also, "Spikes" the "Brain" as well. At 4 years old ... Dishwashers

My dishwasher is leaving a film on all the dishes some of the times. Other times the appliance works fine but more and more often it is leaving a white film on all the dishes as though the rinse cycle is not working well. I have tried filling the jet dry compartment and have been using the same jet dry and detergent as always. The dishwasher is about ten years old and has been working well up to a few weeks ago. Ideas?


Check inlet water quality & whether softening salt is required. Check and fill rinse aid. refer user manual. ... Maytag 24 in. MDB3700 Built-in Dishwasher

I have a KARCHER Model K 2401 which onstart up has normal water pressure rather than the high. I can usually get it to work by removing the tip, pressing the trigger and running some water through without the tip on. The i replace tip and it will usually retain the high pressure. If I stop depressing the trigger I have to go through these same steps. It is like it loses prime. It works well once I get it started putting out the high pressure.


... Karcher 2500 PSI Pressure Washer

I have a Whirlpool DU1055XTSS dishwasher that completely stopped working. I took it apart, found the thermal fuse to be bad, ordered a new, then replaced it and it worked for 2 loads. Now the thermal is open again. What could be "taking it out"? Is the thermal fuse strictly a thermal or does it repsond to current? It's 2 years old, i have already replaced the heating element, the main control board, and now the thermal....twice.


Hi.If the thermal fuse is blowing, that means that there is overheating.Common causes for overheating are:Thermostat cutting off too late.Plugged element.Plugged element means that the element sta ... Whirlpool Dishwashers

I have a Whirlpool Gold Quiet Partner III that is 8 years old and recently stopped cleaning top rack dishes. I remember finding a mylar like piece in the bottom of the tub and threw it away thinking it came off of something we washed (I know, bad thinking.) The mylar piece measured roughly 3-4inx2in and was folded in half. Anyways....the upper arm does not spin and the detergent doesnt get fully dispensed so dishes dont get fully cleaned. I am guessing not enough water pressure to upper arm. Wou


I'm having a similar issue. Are you sure the arm isn't moving at all?\015\012\015\012Generally what I'm finding is either you have a clog or the pump motor is bad.\015\012Hear is the service manual.\015\012 ... Dishwashers

I have a De Dietrich DV640JE1 built in 45cm Dishwasher, working fine for over 3 years. After replacing the connection under the sink to fix a leak it has stopped working. But I dont think this is related. I run a cycle and it fills water in the bottom of the machine, it drains it out in the end but the 2 arms are not rotating and no water comes out. I checked the arms and they are not blocked. A faint clunking sound can be heard at some part of the cycle. I did also run a cycle with the dr


Hello Benny,\015\012\015\012It's highly unlikely that replacing the connection under the sink is related to this problem.\015\012\015\012From the symptoms you describe, it's almost certain that the circulation pump motor has f ... Dishwashers

Follow-up I've removed the lower arm, I'll spend some time and see whether I can get the pobem sorted out. My wife noticed the the detergent was smeared all over the door and repeated tries didn't get it out. Therefore, the water is not spraying. I can confirm the water is filling on the bottom and draining. The heater is working well. I am thinking there is no pressure to send the water through the tubing to the upper and lower arms. The motor is hot to touch (118 degrees with my temp probe). I


... Kenmore 24 in. 15199 / 15194 / 15192 Built-in Dishwasher

I have a Kitchenaid KUDIO1DL white dishwasher which is a few years old now but has worked great since I bought it. Today it has the lean light flashing and will not turn on. there is power, and the drain button seems to work, but I can not get the cycles to come on. When I press the start button, I just get two dash lines and then the unit turns off. Thanks


... KitchenAid 24 in. KUDI01DL - Multiple Color Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1753 seconds