Having problems with your Candy Dishwashers ?

I have a Candy CDI 1012. the water is not heating, so is it the element that needs replacing


Answers :

Repair Help & Product Troubleshooting for Candy Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have a Candy CDI 1012. the water is not heating, so is it the element that needs replacing


... Candy Dishwashers

Candi cdi1012 beeps and lights flash after about 30 mins. It appears that the water is not heating. Do I need to replace the heater element?


... Candy Dishwashers

I have no heat my hot water coming in is as warm as it gets and on dry it will not heat up. Is there a fuse or circut breaker for the element or do I need to replace it. Also if I could ask how hard is it to replace. Thank You Very Much Dino


Just call me on +263912639492, thta's easy.thank you.\012\012Dr. Kelson ... LG 24 in. LDF 7811 Stainless Steel Built-in Dishwasher

DWF614SS not heating water, flow through heating element has been replaced and tested but still no hot water. Do I need to check the thermostat, if so, where is this located? Thanks for any help with this one. Owen.


... Smeg 24 in. DWF614SS Stainless Steel Free-standing Dishwasher

My Frigidaire Professional Series Aqua Surge with Speed Clean has stopped heating water, could it be the heating element needs replaced


My start button doesnt work on the panel ... Frigidaire Dishwashers

I have a Favorit 44070 i and the water is not heating up although the cycle works fine. Will it be the heating element that needs replacing


... AEG Dishwashers

Fills with water, sounds like it starts to pump water then stops, then start again. It attempts to start pumping water 3 or 4 times them turns off leaving the water in the tub. I have read about the water needing to heat up for the cycle to advance. When I check the water that is left in the tub it is warm but not hot. The heating element is not hot either. I did a continuity test on the heating element and it seems to check out ok. I also did a continuity test on the red wire from the heating e


You have a wash pump problem. can be 1 of 3 things. most likely something is caught in the pump impelor if not the wash pump motor may be faulty or ceized or it could be the capacitor for the wash pump motor is faulty. you can try removing the wash p ... Maytag MDB7100AWB Dishwasher

My Hobart AM-14 is displaying a water temperature of 255 degrees but it is not heating the water. I believe the heating elements are good. I don't want to replace the circuit board if the problem


The thermistor in your float and probe assembly or it's associated wiring is shorted. ... Hobart 41 in. AM14-255 Free-standing Dishwasher

CMA-180 Dishmachine-4 years old, used up to a maximum of 5 times a month. After 10-12 loads it shuts down, alto the lights are on, it won't start for about 30 minutes. Is it possible there is a heating element in the machine that needs replacement, or our water heater is not keeping up?


... Cma Dishmachines CMA 180 Free-Standing Dishwasher

Dishwasher temp. current the dishwasher temp. does not seem to get hot enough to clean dishes. The water temp. for the house is fine, so im wandering if the thermastat or the heating element needs replacing?


I have same problem, but I have started to use the high temperature wash and this works well. It probably uses more hot water. ... Whirlpool GU2400XTP Built-in Dishwasher

The water doesn't heat up in the dishwasher. is that the element in the bottom that needs to be replaced? thanks, Kevin


... GE Nautilus 24" Built-in Dishwasher

I have a Chef Classic dishwasher ( model B8913WW) which is no longer heating the water, I assume I need to replace the element but nobody in my area knows where to get parts for this make or model, any ideas please??


If you know how to use a multimeter you can get to the heater connections and check the resistance of the element. it chould be about 26 ohme. Also the over heat protector thermostat should measure zero ohms. Make sure all wires connected to the heat ... Dishwashers

Dishlex Global 300 Fills and then stops. faint electrical smell after a while . Checked heating element that I replaced 8 months ago, seems OK. It has 29X? ohms resistance and looks OK. (I am not sure of the reading on my meter but the element is not fused.) Pumps water in and out OK No blockage in pump or filters Water level looks to be low on filling, only part covers the heating element. I tried instruction book on changing water level using the "Eco" button no response as indicated in


You need to open the front cover and check the wiring for any burnt wire,this happen sometimes,if that does not solve then it't either pcb or electric motor causing this smell.You would be better off with a new one then. ... Dishwashers

I have a whirlpool dishwasher DU915WKSO: when I turn the dishwasher on, the heating element comes on but no water comes into the unit. I recently replaced the garbage disposal and th dishwasher worked fine for a time or two. Since then I have only been able to get water in it once. Like I said, the heating element works but no water in the dishwasher. Thanks for any help.


... Whirlpool DU1055XTS Built-in Dishwasher

I need to replace the heating element and electronic control board on my Kitchenaid KUDS01DL Dishwasher. I have the parts. I have been able to find directions on how to replace the heating element, but am not finding anything on the electronic control board. I don't even know where this part goes. I am guessing somewhere in the door, but can't find any instructions. Help...


... KitchenAid 24 in. KUDS01DLSS Built-in Dishwasher

I have an Indesit IDL500 dishwasher. It had stopped heating the water up, it looked as if it had short circuited and so i replaced it, i have power going to the element. A couple of forums state that it may be the pcb behind the timer/selector switch. Does this pcb control the program selection and heating of the element? or is there a thermostat that controls the stop and start of the heating element? Any help would be greatly appreciated


Hi\015\012\015\012The unit\015\012has two thermostats and you can test both of them for continuity before\015\012replacing, no continuity replace the thermostat. Hope\015\012this helps...please post back fo ... Indesit 24 in. IDL500 Built-In Dishwasher

I have a haier dishwasher model WQP12 AFM, I've replaced the wash pump motor and drain pump (they had been damaged with water after last repair person didn't put widget around drain hose which split and water accumulated on bottom). It well for about two weeks, then it would not go through it's cycle and I noted water not heating up. Have checked element with meter, thats fine, I replaced timersince it wasn't going through its cycle and that has not changed anything. Any suggustions?? Cheers


... Haier Dishwashers

My Candy CDI 1012 Dishwasher will not heat the water,


... Candy DFI Plan Built-In Dishwasher

I replaced the dishwasher heating element, but water still wont heat. Now what?


... Whirlpool 24 in. ADG7540 Built-in Dishwasher

DWI612C wash cycle runs on and on and on. Believing to be a problem with water heating I tried putting a couple large pan fulls of boiling water into machine during wash cycle and this did move it on from wash to rinse. How do I replace the heating element I cant see it it is not in the dish washing compartment? I dont want to call out a repair agent as one can probably buy a new machine for what that will cost. Thank you.


... Smeg 24 in. DWI612 Built-in Dishwasher

Indesit IDL 40 dishwasher. Heating element not heating water. Element has been replaced. resistance = 32ohms. Had a look but not sure where to start. Thanks Malcolm


... Indesit 24 in. D63 Free-standing Dishwasher

I have an E3 error message on m SMEG STX1 dishwasher. I've cleaned all pipes so am fairly sure that the heating element needs to be replaced. How do I access the heating element to test it? If there is a procedure for taking apart I would be very grateful indeed. Type 10031 model no 1471588673


Hi.E3 means that there is a problem with the heating system. The problem is either heating element or thermostat. The heating element in SMEG dishwashers is usually located underneath the appliance (in some model is at one side or at the ... Smeg 24 in. STX1-1 Free-standing Dishwasher

Wife put washing up liquid into the machine and let it run it was full of bubbles and now it wont heat the water think the element is gone but the timer wont move past the heating stage if i replace the element will that sort the problem or will i have to get a timer as well?


If you put manual detergent that hapend, it could burnd electronis card (or mechanical timer-programer blowup), thermostat or the presostat, the heating element must be OK. ... Dishwashers

My dishwasher does not do a hot wash. Why is this? If I need to replace the heating element, how do i gain access to heating element on my Bosch classixx dishwasher?


Hi, a common problem with these machines is the solder coming away from the heater relay. A simple repair if your lucky. Run a continuity test on the element with a multimeter before replacing it, as it is a massive job to change it. I just changed m ... Bosch SHU9950 Dishwasher

Sediment falling off heating element. Is this normal, or do I need to replace the heating element?


Hi,That is normal mineral buildup... in fact many of the element are made to flex a bit to cause the mineral to fall off of them so they don't get too insulated and burn up...heatman101 ... Maytag MDBH945AWW / MDBH945AWQ / MDBH945AWB Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1350 seconds