Having problems with your Champion 24 in. UH-150B Built-in Dishwasher ?
Booster tank is leaking where can i get a new one
Repair Help & Product Troubleshooting for Champion 24 in. UH-150B Built-in Dishwasher
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
Booster tank is leaking where can i get a new one
... Champion 24 in. UH-150B Built-in Dishwasher
Hi, I have a Hoover silent whisper HD98E dishwasher and it's leaking. I know where the leak comes from. Once the machine is on, it pumps the water through the salt container and through these 3 pronged blue container (located on the side). One of these prongs leaks. I believe it is the washer. Can you tell me where I can buy a new washer? Are they specific to Hoover dishwashers or can I get them from Plumbcenter? A quick answer would be very much appreciated. Thanks.
... Hoover 24 in. HD98E Built-in Dishwasher
My DD603 was leaking (both top and bottom) and I went to this web site and the person recommended changing the Lid Actuators which stopped the leaking for about one month. Now each time I run the dishwasher I get about 1-2 quarts of water on the floor. After reading the number of dissatisfied customers should I just buy a new dishwasher or keep chasing the all the problems associated with the DD-603?
In my honest opinion I would just buy a new one. I would say the same thing to change the lid actuators agian. Iam sure it would stop like before and then return later. It may be more cost effective time wise to just replace the unit. Sorry bbest of ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher
My potscrubber dishwasher cleans and drys fine ,but it leaks onto the floor during the wash cycle. Its 10 yrs old should I just get a new one?
... GE 24 in. GSD3330C Built-in Dishwasher
Whirlpool Dishwaser Model #DU8000XX5. Dishwasher won't do anything. Almost as if not getting any power. Was told to check thermal fuse. Noticed some burning around suspected fuse. Ordered new one, but new one doesn't look like old one. Old has 4 connections, new one only has 2. What gives?
My dishwasher is leaking from underneath, front left as you look at it. If i go underneath it, there appears to be a seal on the outside (it does not appear to be the one that runs along the bottom of the inside of the dishwasher) that has come away at one point. Do you know a) how to get the front panel off (the bit that makes it look built in),b) how can i get another one of these seals. I assume if i get one we can just fit it into place. Many thanks, Robyn J
Hi,\012Here is a tip that I wrote about dishwashers and them leaking.Leaking Dishwasherheatman101\012\012\012p80897 ... Neff 24 in. S5453X1 Built-in Dishwasher
Dishwasher I am getting a run around with getting my LG dishwasher fixed properly. We had a tech more than once come in and look at our dishwasher. It has not been fixed and never dried the dishes properly. It is now leaking and going to a "del" level when we attempt to wash the dishes. It is also leaking on our fairly new tiled floor and under our new kitchen cabinet. Your tech stated the dishwasher was not installed properly. The installation dept , Francine stated it is not their problem
Not sure what you mean by a "del" level, but as far a drying issues:\015\012\015\012LG chose to use a very energy efficient drying method which relies on the residual heat of the dishes to help dry them rather than many manufacturer ... LG LDF6810 Built-in Dishwasher
Unable to fit new door panel to front of dishwasher. Have removed old one with great difficulty and now cannot figure out how to get new one on. Have placed the fittings from old door onto new one in exactly the same place but am baffled as to how it attaches. HELP!
Im not sure what new panel you are trying. But if you can still get the old one back on, you can get different panels, color, and designs from applianceart.com. they also custom cut stainless panels to fit or they have a stainless foil that can cov ... Whirlpool GU2400XTP Built-in Dishwasher
Danby ddw497w will only be about 5 min into cycle when digital code E2 appears it then starts beeping 2 min after this it just stops the unit is only one day old it ran once yesterday fine now i get this code no matter what cycle it is on I bought mine new off the internet and it's been running great for about 2 months. Now I can't get it to drain and E2 shows, I can't get my money back because I've had it more than 30 days, if the solution is a pump, I'm tossing it and getting a good one from
E2 is a hose issue. There is either a kink in the hose, the hose is too high to drain or the pump is faulty.1-800-26 DANBY ... Danby DDW497W 22 in. Countertop Dishwasher
I recently purchased a Dewalt DXPW 3835 Pressure Washer from Home Depot.... After 4 hours use I no longer get any pressure. After depressing the trigger, I get a second of pressure and then it just dies. I called DeWalt and they couldn't help and to take it to the Warranty Shop. They informed that they wouldn't be able to look at for 2 weeks so I took it back to HD and got a new one and this one does the same thing. I'm pretty sure it's probably a pretty quick fix but no one seems able to te
... Dewalt DXPW3835 - 3800 PSI Professional Gas-Cold Water Pressure
Bad i bought the 1800 psi washer 2 years ago the head on the hose blew off you sent me a new hose it did the same thing. you sent me anouther hose and it blew off too. finaliy you sent me a hole new washer because of a recall. i didnt get to use the first one all year and now i was going to use the new one the other day 3-28-09 and it is the same washer i had and the head blew off so now i have two washers with no hose, that i can not use. so what do i do now ?
... McCulloch FHH18A Electric Pressure Washer
The wash pump is leaking, not at the larger joining o-ring seal, but through the vents in the bottom of the motor just past the blade/rotor. Is there a small o-ring inside that is on the shaft that may be leaking? Is there a schematic breakdown of this motor somewhere? I already ordered a new one, and will "play" with the old one to see if I can fix it, just looking for some direction.
The shaft seal has failed. Often the top ball bearing becomes noisy after having the water leak through it. The seal is probably a lip seal rather than an O ring. ... Frigidaire 24 in. PLD3465REC Stainless Steel Built-in Dishwasher
I have a GE DISHWASHER model #GSD2100R20BB. The motor/pump mechanism has been replaced with a brand new one from GE, The water valve and timer have been replaced with brand new ones from GE and the dishes on the top rack are still not getting clean, can someone point me in the right direction here; please?
Have you looked at the spray arm itself? sometimes over use the spray hole get clogged with debris, clean it and then check the return water filter for debris. clean the filter and check in the hole under it that feeds the pump. ... Hotpoint Dishwashers
I have a Karcher 2,600 PSI 2.3 GPM Gas Pressure Washer G 2600 VHR that I have used once last summer. I have stored the PW in my basement with no fuel in the gas tank. The PW was never exposed to freezing temps. I cannot get the PW to start. I put new fuel into the tank, the oil is good, I drained the carburetor, and the spark plug works (tested it). I pull the cord and the engine doesn't turn. Fuel value is on, choke is pulled, and the starter switch is turned on. System is practically brand new
Hi I have a similar pressure washer from Kartcher and the same scenario as yours I have owned it for about 2 years and noticed that it was getting harder and harder to start with each time I use it which is months. If your pw has a honda engine on i ... Karcher G 2600 VH Gas Pressure Washer
The top level is not getting clean. We think the passage to the top water jet is clogged. There are two holes in the back that the washing arm fits into, depending on what level the top rack is set at, and one of them is stuck open. We have not been happy with this dishwasher from the start and are trying to decide if we should get it fixed or just buy a new one.
Sometimes it is not worth the headache.dishwashers are a dime a dozen,if you want to happy,just replace it,most dishwashers are unrepairable.no matter what the maytag man says. ... Dishwashers
The circuit board on our Miele G646 dishwasher has failed. do we 1) see if we can get another one second hand and in which case what other models have a compatible circuit board 2) try and get the board repaired and who do you recommend 3) bite the bullet and pay an exorbitant amount for a new board or 4) give up and just buy a new machine Thanks
What is the dwasher doing or not doing and how do you know it's the board. More information required please. ... Dishwashers
10 year old Kenmore Ultra is leaking early in the washing cycle. Wondering if this is worth fixing or need to bite the wallet and buying a new one. I am worried about affecting the new cabinets even though the dishes seemed to be clean on the two occasions that the dishwasher has leaked. Only need a somewhat simple machine- I'd appreciate any suggestions as to what brands I should research if buy is the conclusion. Thanks.
At 10 years old I wouldn't put much if any money into it. Do check the water connections as it may be something simple that just needs to be tightened or a washer replacement. Replacing the valve is a simple and inexpensive fix but don't bother going ... Kenmore 24 in. 17482 / 17484 / 17489 Built-in Dishwasher
I bought my new husky/ honda gcv190 about a month ago, i haven't even started it yet. I didn't realize that the owners manual was for a totally different power washer. I don't want to bid on one,buy one or even spend anymore money getting one. Can someone please help me out. thank you
Http://www.apwdistributing.com/\015\012\015\012 You should be able to download a pdf version of the owners manual here.. you will need your model n ... Pressure Washers
Hello, bought an Hanseatic DW12/BFE in Germany approx. 5 years ago and moved with it to Sweden. Now one of the springs (assisting the front lock opening/closing) did break. I've tried to get a new one via a specialised shop dealing with home machines but withour success. They can only support with spare parts out of their ordinary supply chain. Can you help me? Do you have partners in Sweden or can you send me one or two springs? Thanks in advance for your reply, Petra
Miele 646 sc plus inlet tank solonoid valve on water tank leaking. We moved the machine from one room to another and now this valve is squirting out water. We replaced both door seals thinking that was the problem, then started the machine with a side pannel removed, and saw the jet of water coming from the solonoid valve on the water inlet tank. Any ideas.
... Miele Dishwashers
Water Leak My dishwasher is an Ariston Advantage AF250: I have been told that internally its the same as a Hotpoint DF55. It intermittently leaks water onto the floor from the front at its base during use. At one time it ruined the motor which I had rewound and at the same time I made a new polystyrene float for the base pan overflow switch. All was well for months, but now its leaking again. I have blown through the tubes from the drain filter well to the pressure sensitive switch, but all
Hi there, dishwasher leaking might be due to either of these causes, check these:Main tub sealNote… If the main motor of your dishwasher is mounted vertically, beneath the center bottom of the dishwasher, the foll ... Hotpoint 24 in. DF55 Free-standing Dishwasher
My Maytag model mdb9600aws motor shaft seal is leaking. How do I remove the seal and replace a new one. I am a novist, but I have taken the motor completely out and replaced the seal / gasket that the motor sits in, but there still is a leak. I am afraid the leak is going to destroy the motor as it has corrosion / salt like stuff about the motor. I have attempted to pry the shaft off with the use of 2 screw drivers. I was thinking since I am going to replace the whole motor shaft seal and chop
You are wise to realize the leak would destroy the motor.Take a close look at the diagram to see everything that gets placed on the motor shaft. That should give you a good idea what can/must be removed from that shaft. ... Maytag MDB9600A Jetclean II Built-in Dishwasher
Soap gets stuck inside the soap dispenser, so that at the end of the cycle, there is a clump of soap still in the dispenser. We have also noticed that the rubber seals at the back of the dishwasher (the ones that the spin arms plug in to) are getting worn. Will get new gaskets this week, but wondered if the soap dispenser isn't another problem.
... Maytag 24 in. MDB8600AW Jetclean II Built-in Dishwasher
We have a kitchenaid dishwasher, kudi22ot3, installed in 1992. It is not cleaning dishes even thought the tub is getting water, and we've run dishwasher magic through it a couple of times. The dishes will get clean for a few runs, and then will stop getting clean. Is it time for a new dishwasher or can this one be fixed? Thank you.
Hi,There are 6 major reasons that could affect the cleaning.A nice guide you could follow is :-http://www.partselect.com/dishwasher+dishes-not-clean+repair.htmOther than this, you need to check the pump. Make sure ... KitchenAid Dishwashers
Motor removal Our dishwasher (Model LDS 5811WW) has LE come up when you turn it on. We were told by LG that it needs a new motor...so how do we get one? Also do you have any instructions as to properly getting it out? The clsest repair person suggested is 1 hr. from us and it would cost 3/4 of what the diswasher cost originally.
I am having a same problem. You can open dishwasher sump assembly from inside the dishwasher and check if something is blocking white impeller. I tried to open impeller and sheared screw head as I did't realized it is left handed screw. Even after cl ... LG 24 in. LDS 5811 Built-in Dishwasher