Having problems with your Coleman Powermate DuraBuilt 1400 PSI Pressure Washer ?

I have insufficent pressure on the high side, it like 800 when it should be 2200.


Answers :

Clean out the nozzle with a small diameter wire.
Repair Help & Product Troubleshooting for Coleman Powermate DuraBuilt 1400 PSI Pressure Washer

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have insufficent pressure on the high side, it like 800 when it should be 2200.


Clean out the nozzle with a small diameter wire. ... Coleman Powermate DuraBuilt 1400 PSI Pressure Washer

I have a KARCHER Model K 2401 which onstart up has normal water pressure rather than the high. I can usually get it to work by removing the tip, pressing the trigger and running some water through without the tip on. The i replace tip and it will usually retain the high pressure. If I stop depressing the trigger I have to go through these same steps. It is like it loses prime. It works well once I get it started putting out the high pressure.


... Karcher 2500 PSI Pressure Washer

I have a 2300 psi gas pressure washer, campbell hausfeld, runs fine but water comes out the nozzle like a hose , no high pressure. inlet filter is clean and when you pull the trigger on the nozzle water comes out like a hose but no pressure


If you no longer have High Pressure coming out while machine is running, it's a pump issue. ... Campbell Hausfeld PW2575 Pressure Washer

Hi, I have a Dewalt pressure washer 3100 psi. I want to know why the pressure washer works okay for 1 hour then it stop working completely. the oil is fine, the spark plugs are okay, and when I tried to start it again it does not work. Can you please tell me what could be the problem? This pressure washer is almost brand new I have used it for only like 30 hours for 2 years that I have it. I used it couple times lately but same problem it works for 1 hour then it does not work any. I will


There are two common issues that will cause what you are describing. What you need to do is run the machine until it dies as you are describing. Then pull the spark plug and check for spark. If you do not have spark you have a failing stater. It is v ... Dewalt DPH3100 Gas Pressure Washer

Comet 2700 psi pump lost high pressure after 1 hr of use.


... Comet BXD2527 Pressure Washer Pump

Hi ..I have an Excell gas pressure washer model no. Exwgv2121-3 with Faip 2100 psi 2 gpm vertical shaft pump..the problem is that there is water leaking from every weep hole at the bottom of the pump when running. Oddly enough,the pump still puts out significant pressure but less than it should due to the leaking water. What is the most likely cause of this?..is it the high pressure water seal(s)? If so,how do I repair it?


... Pressure Washers

I have a Pressure Washer VR2500 , 6.5 horsepower / 2500 PSI number on side 123K12-0134-E Residential - Excell. I do not know which is the oil drain plug for the Pump on the bottom. There is an Allens Wrench plug on the side. However when removed nothing comes out. There is also an Alans Wrench like plug towards the back, that does not want to come out. Which one is the correct plug and do you have a picture as I could not order an Owners Manual on-line? Please Advise!


Hi and welcome to FixYa, I am Kelly \015\012First here is the owders manual: \015\012http://www.excellpressurewasher.com/documents/p ... Comet GXD2527G Pressure Washer Pump

Soap feed The soap feed hose on my Karcher 2650 does not suck up the soap into the washer. I pulled off the connector piece that the hose is connected to. I can blow through the hose. There is a little metal finger thing that you can tell pushes up into place when the water pressure is high. It seems like it is supposed to drop down and allow some soap through when the water is running. I found a loose(attached to nothing) gasket, looks like a little donut. It was just free floating in t


I fixed mine works good too, watch my video step by step i put it on youtube ... Karcher G2650HHR Gas Pressure Washer

I have gcv 160 5.5 hp power washer my problem is that the high pressure pump is not working properly when the engine is running the output pressure is very low so i would like to know could be the possible cause of that problem


look for a black plastic cover with a silver snap on top; pry off the silver snap and lift off the plastic cover; next remove the two screws on the top plate then pull out the piston inside - if unable to lift out, start unit and watch it pop ... Karcher 2500 PSI Pressure Washer

Hope u can help when the karcher is conected up and the trigger on the handle is not depressed the machine makes a noise like its trying to presureise the hose it keep kicking in and out i have lost the pressure although it works its not a high enough pressure to be effective


The power washer stops when the gun is closed. This happens because pressure is exerted on a control valve (Spill Valve)...which in turn touches a micro switch and cuts electricity. Now most probably your machine is kickin in an out because the spill ... Karcher K2.26 Electric Power Washer

No pressures plows like water hose - Psi Blue Max 2200 High Pressure Gas Power Washer


... Psi Blue Max 2200 High Pressure Gas Power Washer

I have a north star 5000 psi and I have low pressure it has what looks like a presure relief on the side bottom and it lets alot of water out when motor is not started and a hole lot when running presure gauge only reads about 600 psi when running Thanks in Advance [email protected]


It is possible that your pressure relief valve is on it's last legs. Call the company at 800-221-0516 and get another one. You may still have warranty protection so ask them about that when u call. J. ... Northstar Pressure Washers

Doesn't retain its high power pressure for more than about 10 minutes and then it goes to being like a regular hose. Usually never regains that power unless I leave it off for a long time and sometimes even then it doesn't recover.


The pressure washer may need new gaskets. When these fail, then you get the same result. The gaskets are available online, and at a Honda dealer. ... Honda Pressure Washers

Hi I have a karcher 360 thats working fine with everything from the water side of it but it has lost its pressure and only comes out like a hose, can you please advise of the problem...... Thanks Geoff


Check the pressure relief valve, it is stuck open and not letting pressure increase in the pump ... Karcher 2500 PSI Pressure Washer

Smeg DWF612WH dishwasher has developed a leak. Water comes out of the rectangular hole on the side of the water softner used to mount what looks like a level or pressure switch. A few seconds after the fill valve opens water leaks out, not a lot just a small trickle. After the washer has filled and goes ito its cycle, it does not leak again. Over the past weeks the problem has got progressively worse.


... Smeg 24 in. DWF612WH Free-standing Dishwasher

16 year old GE built-in dishwasher, model GSD900. Springs that prevent front door from falling disconnected. ALL parts APPEAR to be in good condition. I say appear in good condition because I don't know what they are supposed to look like. But I see nothing obviously broken. The 2 springs appear intact. The connecting cable is good. However one of the 2 springs is shorter than the other. It may be shorter because one is supposed to stretch to the other side of the dw? So number 1


... GE Dishwashers

Karcher 2.89M When the trigger is pulled it switches on/of/on etc continuously. A suggestion is that there is a leak in the High Pressure side.


... Pressure Washers

Need a parts manual and preferably a repair manual for a Stihl high pressure washer model RE250K. It has a water leak and previous owner donated unit to me saying he has spent enough money on it and now it has this leak. I am a qualified automotive mechanic amongst other things and would like some guidance; otherwise I will go in blind. Thanks. Bob Hudson Sydney Australia.


... Pressure Washers

My pressure washer starts fine, shoots water OK. After running for 5-10 minutes cleaning siding I shut off machine. I go to start it again within a minute or two and the thing feels like it's just about seized. If i wait until the motor is completely cool, it will pull start freely and start right up. I think something is wrong with the pump, not the engine.


Your pressure washer may not have an ez-start valve installed from the factory. Without the ezstart valve, you will need to hold the trigger on the wand open to release the pressure to easily start your engine. This link will show you wh ... Briggs & Stratton Pressure Washers

Dishlex global 310 - I've cleaned all filter components and removable parts but still it's like no high pressure water is getting through. How do I check to unblock the inflow at the bottom of the unit?


When the Dishlex starts for the first time, there is a\015\012service mode set up. The service mode allows you to set a 'fill-time'\015\012for the water to reach the right level, depending on the water pressure\015\012and flow... So resetting the ... Electrolux Dishwashers

Hello. I have a Kitchen Aide KUDG255HWH1 that will not start from a cold state. The "Energy Saver Dry" and "Normal" indicator light/ switches failed to operate about 1 month ago and since then I have needed to use the "High Temp Wash" and Soak & Scrub" cycles to get the unit to run. Now these two indicator kight will illuninate but the unit will not start when I depress the "On" soft switch. When I depress the cancel switch the unit starts with what sounds like a pre-start cycle. Pleas


Hi\015\012\015\012\015\012\015\012\015\012\015\012Thanks for using FixYa. To reset the dishwasher switch\015\012off the dishwasher from the power socket and mains for five minutes and then\015\012switch it back on. If still the issu ... KitchenAid Dishwashers

KitchenAid KUDPO1IL dishwasher has a buzzing noise during wash (and rinse?) cycles. Recently had to replace the top spinner (and connecting screw), as it had fallen off, but I think the noise was happpening before that. Today I re-clipped the flat pipe at middle back; one side had come loose. That might have helped a bit. Previously, I took out the bottom spinner and found a 1-2" string-like strip of gray nylon under that. I wanted to check a grinder, to see if something was trapped in that, but


... KitchenAid 24 in. KUDP01IL - Multiple Color Built-In Dishwasher

Kenmore dishwasher 665.13843K601 ser. FU4806977 STOCK 13843K TYPE 575-0 Tried to turn it on won't start/ run/ perform any functions The following buttons light up but will not perform functions; Smart wash and heated dry also lights up like it should, pots and pans, normal, fast wash, high temp, sani rinse The following buttons do not perform functions or light up Quick rinse, Turbo ZOne, Delay Hrs., Cancel/Drain, Start/Resume I killed the power to it for 1 minute for reset but d


The touch pad is not working. Pull the front kick plate from font/bottom of machine and there is a 'TECH SHEET'. This has a complete diagnostic sequence for you to go through and verify the functions for you. ... Dishwashers

Maytag Dishwasher circa 2002 - Defective Plastic rollers The plastic rollers that slide the arms of the dish rack keep breaking. I have had this dishwasher for 6yrs now and go through 1 a year. This defect is really annoying for two reasons one; the cost - $50 each - X's 6 years = $300. Secondly, the inconvenience of having a delapitated dish rack that crashes sideways - with the weight on only one side. Presently, I'm about to order my 6th one. I'd like to know if you are aware of this d


... Dishwashers

Hello, I have a couple year old brigs and strattion upright pressure washer. It has always ran great untill recently. It will run for a acouple minutes before dying, like it is starving for fuel. i give it a couple of minutes, it starts right back up and again dies after a couple minutes of use... I have takin the float bowl and float off and cleand the gas tank and fuel line. everything seems to be in order. Do you have any ideas what it could be? I have not tuched the top side of the carb sinc


Check the oil level in the engine itself. Verify that your oil reservoir is full, then try again.You may also want to refer to the owners manual for other trouble shooting tips. Click this link to go to your manual.http://www. ... Briggs & Stratton Gas Pressure Washer 20244
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1095 seconds