Having problems with your Coleman Powermate DuraBuilt 1400 PSI Pressure Washer ?

Hi! Our gun trigger is not working right on Model

\015 Hi! Our gun trigger is not working right on Durabuilt Powermate Model PW0501400 (electic) where can we buy a new one in Pgh., PA?\015

Answers :

Lowes and home depot sell replacement guns for most smaller pressure washers.
Repair Help & Product Troubleshooting for Coleman Powermate DuraBuilt 1400 PSI Pressure Washer

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Hi! Our gun trigger is not working right on Model


Lowes and home depot sell replacement guns for most smaller pressure washers. ... Coleman Powermate DuraBuilt 1400 PSI Pressure Washer

Trigger gun I just install a new hose for my Karcher 330?Hose is working, but the trigger gun is lose, no turn off went is released, the equipment is always on ?..did I missing a part inside the gun ?..


It sounds like you left out the spring in the hose.There are about 10 different models of K330 with several types of guns. Go here and search until you find ... Karcher K2.26 Electric Power Washer

I have a DPH3800 Dewalt pressure washer and the soaper isn't working properly. Right tip is being used but when trigger is not pressed it puts water into the bucket. When trigger is pressed it does **** some solution into the hose but very little and very slow. The valve is opened all the way. I know my former partner used bleach in the system which I read in the manual is a no no but it did work at the end of last season. Any ideas?


How is the pump connected on a john deere 3800 psi. i took out the 4 bolts and drained the oil. pump is stuck to cam. how does it come off? ... Dewalt 3800 PSI Pressure Washer

I have a KARCHER Model K 2401 which onstart up has normal water pressure rather than the high. I can usually get it to work by removing the tip, pressing the trigger and running some water through without the tip on. The i replace tip and it will usually retain the high pressure. If I stop depressing the trigger I have to go through these same steps. It is like it loses prime. It works well once I get it started putting out the high pressure.


... Karcher 2500 PSI Pressure Washer

Karcher engine still run's when gun trigger is released, as if the trigger is help down. Model K2.080


... Honda Karcher G2400HH-R Pressure Washer

Sears Power Washer Model 580-767300 works great but loss of pressure ocurs after a few minutes or working. If you wait and work the pressure gun it will come back for a while


... Pressure Washers

North star petrol pressure washer. working fine, then no high pressure, checked water feed, water filter , pressure relief valve and gun nosall well work sometimes and keep working, when you release the trigger and try in again the pressure gone again. please help, many thanks, richard


Sounds like the regulator is sticking or is airbound. loosen the water connection and then tighten it back. Could also be that the trigger gun is faulty or needs adjustment. Hope this helped ... Karcher 2500 PSI Pressure Washer

I have a Kenmore Ultra Wash Dishwasher model # 15951,it will be working fine then just stop working it will have no power at all.I leave it for a 2 days and starts right up , works for week then stops.


... Kenmore 24 in. 15932 Built-in Dishwasher

Model Karcher 320H 1.141-205 When first switched on the pressure builds up and then the machine keeps no switching on and off, opening the trigger on the lance and it works ok, close trigger and the pulsing starts again, if left like this it would probably burn the motor out. I have lubricated the brass/plastic piston the operates the on/off switch but problem still exists. I have also opened the pump chamber but cannot see any debris or problems with the rubber seals. Any help would be most app


... Karcher 1550PSI Pressure Washer

My dishwasher, a Whirlpool ADP 931, has stopped working. Possibly because the door was opened during operation, right after it was started. There is some kind of error condition indicated through a blinking Start light, but I don't know how to analyze this. This is a quite simple model with very few buttons to press. When I turn the program knob right to start it, the only thing that happens is that the green Start lights begins to blink continuously. There is also another green light


Hello & Welcome to FixYaThis light is reset by pressing two buttons in sequence 3-4 times, to reset your dishwasher press these buttons in sequence:High tem ... Dishwashers

At the beginning the pressure washer was running but there was no power from the nozzle. I stop the gun trigger, remove the nozzle , it works for 1 minute and stop working again Now the washher pressure turns off on its own after 1 minute or less Honda 2400 psi


See attached link:\015\012http://www.wmpcs.com/index.php?main_page=page&id=14\015\012\015\012If you continue to have the problem you m ... Honda Karcher G2400HH-R Pressure Washer

I have a maytag dishwasher model mdbh985aws1that stopped working. The controls buttons on the left light up when pushed but the buttons on the right (including the start button) do not work. Any ideas on what could be wrong? And how to fix it?


The CONTROL PANEL and/or ELECTRONIC CONTROL BOARD are broken. Unless you are good with a multimeter and wiring diagram just order both and send back the parts you don't use. ... Dishwashers

Unit Runs fine, except when you press the spay gun the engine stalls out. Unit was working fine, ran out of gas, filled tank and started engine. Engine was running fine, triggered spray gun and the engine stalls out.


... Pressure Washers

No Water Coming Into SHU43C05UC/12 Bosch Dishwasher: We have a Bosch Dishwasher, model number SHU43C05UC/12. It has been working for more than 4 years, but yesterday I notice that although I hear a motor sound, there is no water in the dishwasher. The LED display on the panel seems to be working all right. I ran a diagnostic pressing and holding Power Scrub and regular wash button then pressing the on/off button. Got C1 at start then P0 and the Regular wash and Quick wash flashing on/off. How c


... Dishwashers

Trigger gun for gas Karcher pressure washer is missing spring or whatever allows the trigger to work...can anyone help with parts advice?


... Pressure Washers

Model 157182d electric preasurewasher northstar power performance general pump TT9061 2 H.P. WORKS FINE AS LONG AS YOU HOLD DOWN TRIGGER, WHEN TRIGGER IS RELEASED PREASURE BUILDS AND KNOCKS HOUSE BREAKER.


... Northstar Pressure Washers

I have this model dishwasher and last year I spent close to $300.00 having this control panel replaced and as soon as the warranty went p it stopped working again, but there is a green light that blinks next to right side where it says clean. It seems like it is blinking in sequence.. I cannot afford to spend this kind of money to have this fixed again. The co. that has the contract with kitchenaid is horrible and do not double check their work. The only thing tey care about is the bck.


Sorry to hear about the trouble with service. I have put together a sheet to show why the clean light blinks and how to reset the control so you can use it. Let me know if you have questions I would be happy to assist. Here is the link to the instruc ... KitchenAid 24 in. KUDP01IL - Multiple Color Built-In Dishwasher

Troy bilt 2600psi 2.3gpm model 160 pressure washer, I hooked everything up like normal, It cranked up fine, when I pulled the trigger on the gun it stalled. When I try to crank it back up the cord wont even pull like its stuck any suggestions would really help me tks..


This sounds like the pump has dead headed. I.e. the unloader valve is sticking. Unhooking all of the hoses should eventually allow everything to free up. Once it is free what you should do is add about 3 ounces of oil into the water inlet connecti ... Pressure Washers

Have power to unit. sounds like it is working. pull trigger on the gun and hardly any water comes out. turn it off and there is pressure coming out


Have you tried pulling the spray nozzle tip off and checking it for blockage? The spray tips have a tiny hole for the water to pass through, and sometimes a grain of sand or debris will get stuck inside the nozzle and restrict the water flow. Somet ... Pressure Washers

My dishwasher 4000 series Model #PLD4375RFC3 isn't working right, when it starts the water runs in than I hear a click like it's trying to start then it doesn't. The timer just keeps counting down it doesn't wash a thing... in order to get the water out I switch to rinse only and it drains the water. What's wrong with it serial # TH91579830.


... Frigidaire Dishwashers

Karcher Model K 2.40, water is leaking from the gun at yellow trigger.


You are going to have to purchase a new trigger gun, they don't offer any parts for replacement on the inside of this trigger gun. ... Karcher FactoryReconditioned K240R 1400 PSI 13 GPM Electric Pressure Was

Hi I have a Zanussi ZD604W which is a built-in model but it is 14 years old so not sure if it is even made now. The problem is that it is not filling with water, everything else seems to be working ie. the element is heating & its making all the right noises!


... Zanussi Dishwashers

Whirlpool dishwasher I have a whirlpool dishwasher model # 665.16519202, and the clean light flashes 7 times then pauses. I was having a problem with the machine working properly right befor the fault code came up and froze it. Can you give me any guidance as to the problem of this washer? Thanks in advance.


Do a "key dance" between normal and heated dry , going bak and forth six times. this will rester the heater fault. That is the clean light flashing code. Now you have to find the cause. Most likely is that there were suds in the last cycle or the do ... Dishwashers

Whirlpool dishwasher I have a whirlpool dishwasher model # 665.16519202, and the clean light flashes 7 times then pauses. I was having a problem with the machine working properly right befor the fault code came up and froze it. Can you give me any guidance as to the problem of this washer? Thanks in advance.


If the dishwasher doesn't sense a water temperature increase, it will stop working and lock the functions (clean light flashes 7 times, all buttons are non responsive).To resolve this you will have to reset the console. Do this by closing ... Whirlpool GU2400XTP Built-in Dishwasher

Hello there.My Karcher pressure washer motor constantly runs with no pressure coming out of trigger gun.I have tried another gun with the same result.The motor should stop/start when you press gun.The model is a 350M plus VPS. Could you please help.thanks


The valve that admits more water to be compressed is stuck. It is likely the O-Rings on it need replacing. No water to the pump, no pressure!\015\012\015\012The motor will stop when pressure is up to the designed pressure. ... Karcher Pressure Washers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1300 seconds