Having problems with your Coleman Powermate DuraBuilt 1400 PSI Pressure Washer ?

My husky gcv 160 with a honda motor, has stopped pumping water. My brother said he went to use it and the motor wouldn't pull so he left it alone, i tried it and it pulled and started fine but the pumps not pumping and the relief valve( guess that's what it is) is spraying intermitingly, Could you please help, Thanks


Answers :

Repair Help & Product Troubleshooting for Coleman Powermate DuraBuilt 1400 PSI Pressure Washer

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My husky gcv 160 with a honda motor, has stopped pumping water. My brother said he went to use it and the motor wouldn't pull so he left it alone, i tried it and it pulled and started fine but the pumps not pumping and the relief valve( guess that's what it is) is spraying intermitingly, Could you please help, Thanks


... Coleman Powermate DuraBuilt 1400 PSI Pressure Washer

Pressure Washer I have a Porter Cable pressure model no.PCH2401.It works fine for 5 minutes,then I can hear the motor loading down and then it stalls out. I tried to start it and it was very hard to pull on. disconnected the water supply and if was very easy to pull and started right up. I noticed the pump was very hot.This unit has a thermal relief valve on it,shouldn't it have released when it gets to a certain temperature .I was thinking maybe this is why it might be shutting the motor


Any leaks from connection at pump to gun and wand assembly if so the valve is detecting leakage and open up again without u squeezing trigger it builds up in the head.if your trigger gun is leaking internally then you will need to replace the gun thi ... Pressure Washers

Ge model # gsc3200j01ww dishwasher. when the door latch is closed, nothing happens. motor does not start. if the timer is advanced to the next part of the cycle, water will spray into unit until float valve is triggered. water will not pump out, motor does not start. bailed out water, checked for stuck float valve-ok. removed drain screens and filters, cleaned. no motor, drain, or start. what parts should i check? always rinsed dishes before putting in washer. unit is portable or undercounter


... GE 25 in. GSC3200J Built-in Dishwasher

The washer cycle stopped without warning, i thought the timer or the timer motor but it is not the timer works fine and so is the motor. but the timer motor runs til the washer motor starts than is the timer stops and the washer is working but not cycling so no rince or drain or soap etc... just pumping water. if you can tell me what might be the problem, thank you. like i said the timer stops when the washer motor start.


... Jackson JPX-300L Dishwasher

Model 01902 2350 psi . engine runs fine , sprays out nozzle but lower pressure and water sprays out plastic elbow on relief valve , that is supose to **** in soap if used , cant hold finger over spray from elbow , high pressure , took apart relief valve and plastic valves all orings are ok , brass pump seals look ok , all back together , still blows out elbow . ?? plastic spools were out by somebody else , not sure if they are in right , cant find picture to compare .


It sounds as if the non return valve in the elbow is the wrong way around .The o-ring normally goes in first then the ball then the spring. Try it and good luck. ... Pressure Washers

I have the E3 error on my Smeg DWI614 dishwasher which would indicate a heater error, however it is heating the water in the bottom of the machine but it seems to time out. The main issue seems to be that the recirc. pump is not running during the heating phase. I have taken the pump out, checked the connections etc. twice now and everything seems fine (the motor runs when tested). When I have done this (both times) the dishwasher has started again and run for 20+ cycles fine, then the issue com


... Smeg DWI614 Built-in Dishwasher

Troy- Bilt pressure washer #020209 , 7.25 Briggs & Stratton, AR water pump #SJV 3G27-1. Boggs down an cuts off acts as if motor is getting tight with wand in use or not. After shut down its easily starts up an repeats itself. Removed pump motor runs fine.


... Briggs & Stratton Power Products 1539 Pressure Washer

I have a 4,000 psi, 4.5 gpm 45G cat pump powered by a 13 hp honda engine I can not seem to be able to adjust the unloader valve to give me pressure over 950 psi and even at lower pressures, the pump will not deliver consistant pressure without bouncing off to the relief stage and back into the tank Are unloader valves worth repairing, or should i look at just buying a new one my current thought is to buy an EZ start Pulsar


I would just purchase a new unloader valve, they usually aren't worth rebuilding. I would like to have a picture of the set up that you have, if you can send me a picture of the unloader region of the pump I can get you are price on a new one. email ... Honda Pressure Washer PSI 3000

I have a Karcher K5.86m pressure washer and the electric motor wont start. I've done the obvious like fuse in the plug etc. It was working fine one day, then got it out again and everything seems fine except the pressure pump wont start when I press the on button.


... Karcher Pressure Washers

My Bosch diswasher water inlet work fine, when the wash motor or cycle need to start nothing happens. The timer is advancing normal. Water outlet(drain pump) is also working fine. There is no woosh sound (start of wash cycle) and arms is not rotating.


Hi,\015\012\015\012it sound's like the wash motor is either seized or just stuck, let's hope it's the later. Bosch had issued a service tip about this problem several years ago titled "Loosening Frozen Impellers" strange choice of word's considering ... Bosch 24 in. SHE44C02UC / SHE44C06UC / SHE44C07UC Built-in Dishwasher

I have a northstar model 1577501-A motor runs great pump will not generate pressure and makes a nasty noise. I have removed the pump from the motor it looks just fine how do I get repair advice? maybe the valve body is messed up


... Northstar Pressure Washers

My pressure washer starts fine, shoots water OK. After running for 5-10 minutes cleaning siding I shut off machine. I go to start it again within a minute or two and the thing feels like it's just about seized. If i wait until the motor is completely cool, it will pull start freely and start right up. I think something is wrong with the pump, not the engine.


Your pressure washer may not have an ez-start valve installed from the factory. Without the ezstart valve, you will need to hold the trigger on the wand open to release the pressure to easily start your engine. This link will show you wh ... Briggs & Stratton Pressure Washers

RY80940 The valve under the pump is leaking. I think it is a pressure release valve but I am not sure. I tightened it when I had to re attach two bolts that were holding the motor on the metal case then it worked for awhile then it started to leak and I lost all power. Should I tighten or loosen it or is there a washer that needs to be replaced?


... Pressure Washers

Problem for Kenmore 24 in. 15992 Built-in Dishwasher Previously answered by Ginko but have not had any responses since June 18 and problem not solved. No water flow into dishwasher. Actual model is Kenmore Elite undercounter dishwasher 665.15982990. Float is not stuck. Worked fine for 10 years until mid May. Display shows cycle is on and counting, for all the different cycles. No valve or motor sound when starting cycles, only a single electronic click. When cycle is canceled, motor does s


Hi.Sorry about your old query.If there is no power on black wire and no filling, then check and eventually replace the thermal fuse. The thermal fuse is attached to control board. If it is faulty it will read continuity, norma ... Kenmore 24 in. 15992 Built-in Dishwasher

Motor makes noise shortly after starting, makes normal sound level during main body of wash, then makes noise again during what I'm guessing is the rinse cycle. Not sure if it is a pump or motor problem. Slight electrical smell noticed after finishing the ''cancel/drain''. Water does not seem to be sprayed around washer during normal cycle, even though water has been in the washer.


Make sure the sprayer arm is turning freely, check for something stuck in the base of the sprayer arm (food or utinsel) preventing it from turning. ... Dishwashers

FDW70 dishwasher, starts to fill with water, shows pre wash on control panel, then pumps out within about 2-3 minutes, but has vertualy no water in it. Puts up code A10 on control panel, can still hear the pump going even when l open the door. Have replaced a burnt out heater tube with a new genuine unit, also have removed & checked fill valve & this works fine.


Hi,Try this few steps;Turn off the water supply to the dishwasher and remove the hose, turn\015\012on the machine for a couple of minutes in a fill position then turn off\015\012the machine, reconnect the hose, turn the ... Hotpoint 24 in. FDW60 Free-standing Dishwasher

My dishwasher only fills half way and it dosn't go through the wash cycle. It pumps the water out and then go to the rinse cycle but has the same problems with the water level. We have checked the motor, pump and the water valve. It seems to be working fine. Thought it might be the timer.


Hi,\015\012\015\012This is an issue with the wash motor..\015\012There are two motors,a wash motor and a drain pump/motor assy\015\012The wah motoe must have been the issue with the case.Changing the wash motor will solve your ... Dishwashers

MaytagMJD2005 Machine is in middle of cycle power on. water on. The main pump motor attempts to start. motor spins so the pump is not jambed. pump out pump starts at the same time. Motor does not overheat.


So what is the problame it jusy seems you telling us there isnt one and u have solved it and giving advice. ... Maytag Dishwashers

I have a Coleman powermate clean machine pressure washer 2500 psi 2.36gpm and has a 6x200 honda 6.5 horse motor. I just bought at a garage sale.It started just fine when I got home and in less that 2 minutes quit. It says the engine will stop automatically when low on oil. what kind of oil should I use and for the pump what kind of oil do you use?


... Coleman Pressure Washer PW0881800

I have the Kitchen aid KUDS01DL dishwasher. It was working fine until last week. When starting a cycle, the washer fills with water. Once filled, the motor makes a humming noise and does not circulate the water. I end up stopping the cycle and the discharge pump empties the water. I took apart and cleaned the basin this morning. I did find some random garbage but it did not seem blocked. Do you have any ideas?


... KitchenAid 24 in. KUDS01DLSS Built-in Dishwasher

ASKO D3432 At start up, drain pump works fine to remove water. Inlet valve kicks in and it fills with water, then it shuts off and gives a fault message. "Water Inlet Fault". There are no "kinks" in the water hose and I can see water fill the side "reservoir".


... Asko 24 in. D3432XL Dishwasher

No water flow into dishwasher. Float is not stuck. Worked fine for 10 years until yesterday. Display shows cycle is on and counting, for all the different cycles. No valve or motor sound, only a single electronic click at start of cycle. Actual model is Kenmore Elite undercounter dishwasher 665.15982990


Hi.Try tripping the circuit breaker or disconnecting power cord for a couple of minutes. While power is off, check the inlet cable at the back of the machine.If\015\012there is no water getting into the machine, and there is n ... Kenmore 24 in. 15992 Built-in Dishwasher

Asko 3100 Dishwasher - when I press the Start/Stop button, all the lights on the cycle program button light up and the dishwasher motor starts up but no water appears in the machine. The dishwasher repair man guesses it is the valve or the computer but is not sure.


I am assuming you have the ASKO D3100 dishwasher.\015\012\015\012Can you please confirm which lights are flashing - is it one light on top of the program knob or all of them including the one on the Start/ Stop knob.\015\012\ ... Dishwashers

Frigidaire dishwasher Water does not go through arms, bottom or top, at all (does not wash). You can hear motor running. Pump works fine; discharges water as normal and fills to proper level. Problem just started with no warning; no strange noises etc.


CHECK WATER INLET SOLENOID OR TIMER ... Frigidaire 24 in. PLD2850 Built-in Dishwasher

We have a frigidare model PLD4375RFC3 dishwasher that won't turn on! I select the cycle and press on and it just shows me the time for 15 or 20 seconds and then turns off. I opened the bottom and everything looks ok, there are no leaks and all wire connections are in place. Latley the motor has been squeeling a bit and the dishes have not been clean so obviosley something has taken a dump! I just need to know were to start, is it the water valve or circulation pump and how do I test them?


... Frigidaire PLD4375RFC Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1484 seconds