Having problems with your Coleman Powermate DuraBuilt 1400 PSI Pressure Washer ?

I have no pressure when I press the wand handle in. The motor is on water comes out but without any pressure at all. Fix??

\015 Model DB1404\015

Answers :

Repair Help & Product Troubleshooting for Coleman Powermate DuraBuilt 1400 PSI Pressure Washer

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have no pressure when I press the wand handle in. The motor is on water comes out but without any pressure at all. Fix??


... Coleman Powermate DuraBuilt 1400 PSI Pressure Washer

I have an older Landa Pressure Washer. The burner is not working. Once I get the machine running and water flowing to the pressure washer, with the wand pressed, I flip the burner on switch....and nothing...I have no idea how to work on a pressure washer burner. I have been told it could be the igniter, but I don't know how to fix it if it is. Any help is appreciated.


Check for 12V at the igniter connector with the unit running. If you have 12V and no igniter it may be stuck or bad. Thrun the unit off and read continuity across the DISCONNECTED igniter plug / terminals to the igniter. No resistance = open ignit ... Pressure Washers

I have a KARCHER Model K 2401 which onstart up has normal water pressure rather than the high. I can usually get it to work by removing the tip, pressing the trigger and running some water through without the tip on. The i replace tip and it will usually retain the high pressure. If I stop depressing the trigger I have to go through these same steps. It is like it loses prime. It works well once I get it started putting out the high pressure.


... Karcher 2500 PSI Pressure Washer

I have a zr2700 pressure washer. As soon as it is started, water pumps through very forcefully. Pressing and releasing the triger on the wand does not control the water. Do I need a new wand or is there a problem with the pump


... Pressure Washers

Low Pressure with no hose attached, pressure is good, attach hose without wand and pressure drops 50%. Have had pump apart 10 times, have checked bypass valve, have even removed bypass and filled passage way so water could not bypass wihout any change. Am down to thinking pump casting is cracked allowing bypassing to happen. Does each of the three piston chambers have a check valve so one piston is not pumping back into another piston chamber?


I worked at a tool rental while attending college and had the opportunity to work on a variety of pressure washers, however, they were of the commercial type. Commercial washers are slightly different in that they usually have seperated components fo ... Karcher 2500 PSI Pressure Washer

Karcher 3100 pressure washer, motor runs fine but when I squeeze the trigger on handle, high pressure pump won't come on unless I remove tip and water is coming out of wand without restriction. Help anyone have any ideas? It did come on once but when I let go of trigger it wouldn't come back on.


... Alfred Karcher Quick Connect Nozzles 2600 3100 Psi 5 Pack

Db1404 I have no water pressure when I depress wand. There is some water and the motor is running. Fix?


... Coleman Powermate DuraBuilt 1400 PSI Pressure Washer

Karcher k3.68m leaks from the pump area. If I turn it on without holding the trigger down on the wand it will not blow pressurized water. If the motor is idle and the water is turned on then it leaks a lot from the pump area. What part should I replace?


... Karcher PSI Electric Pressure Washer

I have a Campbell Hausfeld Furniture Paint Sprayer - paint is coming out without me pressing the handle - continuously spraying. When I try to press there is no pressure it just flops back and forth. Can someone help as to what I need to do to fix this? Thank you


The paint is too thick try thinning out the paint would be one possibillity clogged tip/filter. Also what happens sometimes is when using latex it drys fast so sometimes it starts gumming up the springs so it doesnt allow the trigger to close up all ... Pressure Washers

Our GE Profile Dishwasher is not working since today afternoon. The electronics seem to be working fine but the water supply does not start on pressing the start button. The dishwasher seems to go on with its cleaning cycle without water. We don't know how to fix this or to even check any plumbing/water supply problems. Please help.


OK First try this below....\015\012\015\012Ok so your dishwasher won't do anything... it justs sits there and "Hums" you can't make it respond to any controls, and the ONLY way to Stop it. is to unplug the unit, replugging back in it simply "Hu ... GE 24 in. Profile PDW9880JSS Built-in Dishwasher

Briggs and Stratton pressure washer will not start. I have a 6.75 hp pressure washer that is only a year old. when I pull cord it turns over but does not start. I changed plug and checked it, I have spark when pulling. I have 40-50 psi of compression when pulling also. gas was drained and is brand new. it was working fine last time it was used. I have tried starting it without the water line or spray wand hooked up and no difference. After about 10 or 15 pulls, can smell gas when I am trying to


Hello dave, the problem is compression to low,you need 60 to 130 lbs to run engine,check for blown head gasket,or bad rings,or a stuck open valve,hope this helps,, ... Briggs & Stratton Pressure Washers

Kodiak 4000 Bear, Washer runs smoothly, press trigger and washer begins pulsating jets of water, good pressure, used air hose on washer water line and wand, problem still exists. wash application


... Pressure Washers

I have a Husky pressure washer with a Honda 2600psi engine. Problem is, no water will come from the pressure hose. I connected the water w/out the pressure hose and water flows thru strongly. I then connected the pressure hose w/out the wand and water flowed thru the hose fine. When I connect the wand and pull the trigger, nothing. I have replaced the wand and that was not the problem. Please help.


Check the quick disconnect to the wand these are spring operated and can get stuck ... Pressure Washers

Kenmoore Quiet quard 3 Model #665.74363K1 Serial #FS3502091 The unit will not drain properly. When in drain mode, it will drain slowly when diconnected from the disposal and lowerd to floor, and drains even slower at disposal level, or hooked to disposal. Disposal nipple is clear. I removed the hose and flushed it out with high pressure, found no blockages, hose flows freely and did not fix the problem. The motor is turning and seems to pump water fine, all wands are truning with powerfull spray


... Kenmore Dishwashers

Have three yr old Troybuilt pressure washer. Model 020276. Used 5 times. Engine starts up ok, but when pressing wand, it kills the motor. Also have hot water flowing from valve that I had not noticed before. HELP. LA moi.


... Honda Pressure Washers

Folks, I have a Karcher 5.55 home water blaster that pulses at the highest pressure on the vario power spray wand. It works fine on the lower pressure settings and with the rotary spray wand. I live in a temperate climate, depressurize and drain after each use, always prime the pump, have good water supply, cleaned the filter etc etc. Any pointers on to do or test next? Any help greatly appreciated.


... Karcher Pressure Washers

I have a Honda gc160 5.0 pressure washer. All fluids are fresh. Water is hooked up with plenty of pressure but the water pressure is up and down then goes completely out. No water will come out of the wand? Please advise. Thank you.


Needs new pump ... Karcher 2500 PSI Pressure Washer

Kitchenaid KUDP01FL : Hi, machine will start to fill (on heavy), and then will not engage into the wash cycle. Have to press cancel to drain water. All other settings ( china/rinse/ normal wash) when button is pressed and door closes will "click". No water fills into machine. Have to press cancel to end cycle. Can it be a bad connection being i tryed trial and error and banged on inside of door to maybe "fix" it. NOW, heavy cycle does not fill with water, just a "click" noise. Thanks for


... KitchenAid 24 in. KUDP01FL Built-in Dishwasher

Assembly plans for karcher 2400 psi pressure i recently had a problem, with my pressure washer. i was cleaning out my hose and took the hose assembly and brass fitting off. run water threw it thought i had cleand it out, put it back together and now when i hooked my water hose back up the water comes out of the despencer instead of the pressure wand. does eny one no what i need to do to revurse this?


... Honda Karcher G2400HH-R Pressure Washer

I have error E:15 with a flashing water tap sign - I've tried the following: a) Clean filter at the bottom - now flushes out with b) remove power - return power c) remove and clean fiter for incoming water at a sort of valve Nothing! when I attach power it continues to flush out (even without water) if I put water in it evacuates without problems. The tap does supply water I've check and with more than sufficent flow and pressure! ...Help .....Thanks Gary


Hello Gary,\015\012\015\012You didn't specify the brand or model number of the dishwasher, but I suspect it's a Bosch, in which case the E:15 error with the flashing tap sign and the drain pump running continuously means the anti-flood pr ... Dishwashers

Turn water on then actuate wand trigger. Pressure washer leaks when wand trigger is actuated and has very low pressure/flow output. After releasing trigger the pressure cycles on - off at approx 1 second interval. I suspect that the plasstic oulet tube is leaking causing low pressure leak out of bottom when trigger is actuated and causes pressure switch to cycle when the trigger is released. Any Help? This pressure washer is approx 18 months old!


You gave a very close solution yourself for the problem. But other leakages can cause such symtoms.Forexample a leaking head or a leaking chemical inlet. These can be caused because the spill valve (pressure control valve) is stuck. When this valve s ... Karcher PSI Electric Pressure Washer

Appliance had been working fine now all of a sudden no water is running in the dishwasher.The machine appears to run through all of its cycles but without water. The water pressure in the ajoining sink appears a little low though the water pressure in the rest of my home is fine. I see no water leakage anywhere. Do I need to call an appliance tech or should I call a plumber? Thank you.


... GE GSD1000 Dishwasher

Maytag, Quiet Partner II. Top water wheel is not getting does not get sufficient water pressure. Without sufficiant water proessure the water wheel won't spin, without the spinning effect dishes on top rack do not get clean.


Motor-Pump Drive assembly is defective.Hey while you have this machine apart pull the drain pump off and look for a jammed flap,it's rare but check it anyway.(to remove the drain pump just twist it and pull it off).For the non believer's out there ,t ... Dishwashers

I have an shx65905uc bosch dishwasher that runs and works except for that there is not enough water pressure to rotate the top wand or operate the top sprinkler. The bottom wand does have water and turn and does the top but it is not enough to turn it. If i remove the bottom wand and plug it off then the top will work properly. I have cleaned all screens and removed the plate to access the pump and all seems fine. Any Thoughts


... Bosch SHX65P05UC Dishwasher

AT FIRST WITH JUST THE WATER ON (PUMP OFF) I SQUEEZE THE WAND AND WATER COMES OUT ABOUT 3 FT. THEN WHEN I START THE PUMP AND SQUEZE THE WAND ONE STRONG SQUIRT COMES OUT THEN GOES BACK TO ABOUT 4 FT. NOT MUCH PRESSURE. CHECKED THE CHECK VALVES, AND THE 3 PISTONS THEY ALL WORK. PUMP NO.AXD 3020


Hi, W/D here.Leave the water on, and hold the trigger down for about 5 minutes to get all of the air out of the system. Letting off of the trigger occasionally and then opening it up will help displace any air in the chambers. While still hol ... Comet Axd3020g Pressure Washer Pump 27 Gpm 2000 Psi
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1064 seconds