Having problems with your Coleman Pressure Washer PW0881800 ?

I have a Coleman 1800 pressure washer and it won't idle consistently. Meaning it fluctuates between high idle and low. It doesn't matter if I have the hose engaged to vary the load. Any thoughts?


Answers :

Sounds like the air filter may be blocked or the carb has a dirty jet in it
Repair Help & Product Troubleshooting for Coleman Pressure Washer PW0881800

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have a Coleman 1800 pressure washer and it won't idle consistently. Meaning it fluctuates between high idle and low. It doesn't matter if I have the hose engaged to vary the load. Any thoughts?


Sounds like the air filter may be blocked or the carb has a dirty jet in it ... Coleman Pressure Washer PW0881800

There are two hoses coming from my Bosch SHE45M06UC dishwasher. One is obviously the drain coming from the back of the unit, and the other is attached to the side looped and not connected to anything. I went online to the Bosch website for a installation manual and it describes this hose as a air venting hose. Does the end attach anywhere or does it just hang loose on the unit. My husband detached it from its original position and thought it was part of the water line. HELP!


Many people realize the dishwasher connects to a little hose on the sink, it is called an air gap. However, many people wonder " The air gap is there to prevent the water from being siphoned out of the dishwasher. When water flows through the drain ... Bosch Dishwashers

Assembly plans for karcher 2400 psi pressure i recently had a problem, with my pressure washer. i was cleaning out my hose and took the hose assembly and brass fitting off. run water threw it thought i had cleand it out, put it back together and now when i hooked my water hose back up the water comes out of the despencer instead of the pressure wand. does eny one no what i need to do to revurse this?


... Honda Karcher G2400HH-R Pressure Washer

Idl 705 Hi our indesit IDL 705 stops half way thought a wash with the red salt light on(despite salt being full), can reset it and get it away but not ideal any ideas? Thanks


I have the same problem, what was the problem and how did you resolve it? ... Indesit 24 in. IDL700 Built-In Dishwasher

Hello. my dishwasher leaves gunk on the inside of glasses that were wiped clean before washing. It seems like that would mean the drain to the disposal is clogged but the hose is clear and the impellar is free. I blew on the hose and got movement in the disposal. the impellar is clean and new looking. I thought it would be a little dirty? Any help would be greatly appreciated. I will answer any question you have in case i didn't explain it well.


There are many probable causes of failure .A dishwasher's water inlet valve is its most common part to fail. When \015\012your dishes are not being fully cleaned, quite often a faulty water \015\0 ... Dishwashers

I own a build-in LG Stainless Dishwasher (modle: LDF1178ST). It stopped draining water during its recent startup due to its idle (no operation) for about a year:). I can only feel the hose full of water by touching the drain hose between the washer and the sink desposal. It's hard to check other part of dish washer since it's built in our cabinet. Could any dishwasher expert help to advise how to trouble shoot or fix this problem. Thanks, Alex Chen 571-220-7484


There is a float in the bottom of the dishwasher that tell the motor to turn on and pump out the water. I would check the float first to see if it is hung up and not raising to tell the dishwasher that there is water in the base. Check the check valv ... LG Dishwashers

I have same problem with Chicago Electric # 47761 electric pressure washer as Aug 10 2010 writer had w/ Karcher 2500. Runs briefly then stops. Pressure is trapped in hose. I cleaned hose disassembled & greased valve in handle. No improvement. Problem appears to be premature wear of trigger cam in handle - both are plastic. Valve body is rigid nylon. Any thoughts??


... Pressure Washers

I have a briggs & stratton pressure washer that every time I engage the spray hose my pressure washer stops. Why???? I have left it running for a couple mins. before engaging, doesn't seem to help


PROBABLY the valve that admits the water to the pump is sticking. USUALLY bad O-Rings. If the valve sticks closed, the pressure won't build up. If it sticks open, the washer will stall. Most other problems are engine problems due to bad gas, carb ... Briggs & Stratton Pressure Washers

I have a Kitchen Aid KUDS03CTSS3 dishwasher. Dirty water is staying at the bottom and nothing comes out the drain hose during the entire cycle. The drain hose is looped above the kitchen P-trap, although for a time it wasn't. I use a wet vac to get the water out but there is still water below the fine filter. I thought if I could get the fine filter off, I could clean out the bottom as I think that it's full of crud down there that may be blocking things. I can't figure out how to get the l


Hi,Thanks for the follow up. I am glad it worked out for you. If I can Help in the future let me know. http://www.fixya.com/support/c64627-kitchen_aid ... KitchenAid 24 in. KUDP02FR Built-in Dishwasher

Hi, I have a Karcher 3.75 jubilee powerwasher, there is water coming out from where the high pressure hose connects to the machine and the unit pulses when idling but works perfectly without drop in water pressure, when trigger on gun is pulled, on closer examination the metal connection on the hose turns, is this the problem or something else. thank you.


... Karcher Pressure Washers

Bosch Dishwasher 8502. Disconnected and laid up for six months. Now reconnected but 'check water' light comes on. Have removed filter in tap end of hose and checked for no kinks. Plenty of water pressure at entry point of hose to machine. Ant thoughts?


... Bosch Dishwashers

Are Candy dishwashers cold or hot fill please , I have been given one and it has a red hose on it , the person who gave it to me has moved and I have no contact for him! I thought dishwashers are predominately cold fill so am wondering if he had to replace the hose and only had a red one so do I connect to hot or cold pipe please


We don't have Candy brand here in the US, but all dishwashers are always connected to the hot water. ... Candy 24 in. CD950 Free-standing Dishwasher

I just bought a used LG LDS 5811ST stainless steel built in dishwasher. The previous owner said he bought it 4 years ago. It's in great shape but doesn't work. It powers up but the water is not pumping into the dishwasher. The previous owner said that he thought it was the pump. He said he took it apart once and cleaned a bunch of crud out of some hoses and it worked for a while then started making funny noise and stopped. When i got it home i powered it up and connected water hose. It seems to


Rom the Service Manual:"1E INLET ERROR Not reached to the normal water level in spite of 10 min. water supply.The Hall sensor is OK?Check the frequency of Inlet Water by the Test Mode." ... Dishwashers

Cycles - pressurizes when trigger is pulled, then motor sets back to idle immediately as if trigger is let go, but is still engaged. Pressure and idling happens within 2 seconds, continously cycling


A lot of commercial and industrial grade pressure washers especially have a safety feature that will either shut down or will return the motor to idle if you do not have an adequate supply of water to the pump to protect the plungers and valves from ... Coleman Pressure Washers

My Troy Bilt pressure washer (Model: 020296-01) idle is up and down. When I engage the trigger I get pressure for a second and that's it. If I squeeze the trigger a second later I get the same thing and so on. Is it just the idle that needs to be adjusted or something else?


... Briggs & Stratton Pressure Washers

Fails to drain , fills and cleans but doesnt engage pump to drain.


First I would check the drain hose from the bottom of the washer to the main drain for a clog. If it's OK then I would start looking at the pump itself. If it checks out then I would start looking real hard at the timer. ... Dishwashers

Karcher k3.86 lowered operating pressure and constant surging at idle, it back feeds into the water feed/supply hose until trigger is pressed


It sounds like your non-return valves are damaged. in the pump there are usualy 3 non-return valves, these are located under 3 large brass hexagonal caps. take the valve out and inspect them. if you are lucky they may just need cleaning, as sometimes ... Karcher K2.26 Electric Power Washer

When I release the trigger it "idles" fine, but when I re-engage


I have seen this problem alot and it can normally be rectified by clean out your unloader/bypass valve the orings on this valve get damaged as jerr said by leaving hoses and trigger pressurised, the easiest way to test if it is a faulty unloader valv ... Briggs & Stratton Power Products 1539 Pressure Washer

We live in an apartment and our hot point dishwashers timing is all off and i thought if i could fix it myself, i'd love to do that instead of calling our manager, i will call him, but if its an easy fix i'd like to try it out.. it will just stop in mid cycle, and you have to manually more it a fraction of an inch to get it restarted, then at the end it doesnt fully drain, and the drying takes forever, so if i cant fix it, i'll ask for a new one..


It might need a new mechanical timer (sounds like the timer is sticking) installed and the parts will cost money... so you might want to go the route of the manager. The dial that you turn to set the dishwasher is part of the mechanical timer. Someti ... Dishwashers

We have an LG dishwasher LD14AT1 P/No 3850ED3005R. It kept signalling an error to do with a leak- all hoses etc were checked, one relaced but no fault was found, so we had a repair man come out and he repalced the electronic board at a cost of $200.00. The error still kept signalling (by the dinging sound). It was then discovered that the appliance had rusted and there was in fact a leak in the base of the machine, not a fault in the electronics. The machine has just remained idle since. I belie


I agree that it should not leak like it is dowing. Is it really rusted/corroded? Or is there a whole?The tech should have seen the leak with ease. Replacing the PCB was uncalled for.Regarding the leak, I would gather the pr ... LG Dishwashers

No water pressure coming out while ingine is running. hoses/ attachments not clog. Pulled and opened pump, didn't see anything broken although noticed pump was filled with oil/lubricant but about 1/4" below top surface. Is it suppose to be filled to the top? What kind of oil is used on the pump? And how come there's no water pressure coming out while the motor is running and handle trigger engaged?


If you can find the model # then you can call tech support for free advise.\0121-888-279-9274 ... Karcher Pressure Washers

Jackson jp-24b purchased this machine used, cant figure out how to work it. I flip the auto cycle on, and then the power switch. The fill light turns green and i assume water is filling up in the machine. In the meantime there are two small red external hoses that hot water comes and i currently just have those hanging in the sink. At the same time, nothing is happening during the wash cycle, the wash gauge doesnt even move only the rinse gauge. Also when i try to drain it nothing happends (begi


It needs a new drain relay box 120 volt the drain is stuck open the jp 24 were not very good machines the red lines are drain lines if you plug up the drian lines at fillup the machine will wash but now it will never drain a new drain box is not c ... Jackson JP-24B Built-in Dishwasher

E6 I have been getting E6 error message over and over again. I have had the machine to pieces, cleaned out the pump and hoses, and still the same problem. Occasionally, the error message changes to E8 or E1, but no matter what, I can't get it to work. Any ideas? When I start the machine, select any program and close the door after a short while the machine does not complete the wash cycle and I get the following message either: E1 or E2 will appear in the control panel Any suggestions Dave M


I had this problem and fixed it tonight. When selecting a program water pumps into the machine, but with no drain i ended up with too much water and error code E6.\015\012\015\012I traced the fault to a broken wire between the electronic ... Smeg DWI614 Built-in Dishwasher

Hi, I washed a candle, yes candle, in my daughters brand new lg dishwasher and now it doesnt work. Surprising i know. After spending days tearing it apart and removing all the wax out of the inside as well as pipes and hoses, etc it will now do everything but drain. Can you help?


The problem is that when you ran a wash cycle.. the heater came on and melted the candle and some wax probably ended up in your pump or hoses in/out of that pump.. Since you did not provide a specific model number, I cannot provide specific details o ... LG Dishwashers

I HAVE A TEKA DW6 59FI DISHWASHER. IT SEEMS TO GO THROUGH THE MOTIONS OF A WASH CYCLE BUT THEN STAYS FULL OF WATER. ANY THOUGHTS ON THIS MATTER WOULD BE GREATLY APPRECIATED.GARY/MANCHESTER.


... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0720 seconds