Having problems with your Coleman Pressure Washers ?

Pressure Once I have the powerwasher started and going (water to it before starting) i can't get it to go to full pressure it will prime up like it's going to go to full pressure give me just a shot of full pressure then go back down to probably half pressure and remain there then prime again for a second then back a coninues cycle! Maybe there's a seal or something somewhere I should look at. Hose and pressure from house is good, the seal whee the hose attaches to the bottom of the washer is ne


Answers :

This is usually a problem with the "dump valve" defective in not being able to hold the pressure but only able to release it prematurely as it should only do so when to much pressur is built up inline. Only recommend qualified pump tech. But check pump oil level and add 10w 30 pump oil if needed and retry. Also see my TIPS AND TRICKS ON PAGE
\015\012Thanks and please rate a fix ya!! jj505
Repair Help & Product Troubleshooting for Coleman Pressure Washers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Pressure Once I have the powerwasher started and going (water to it before starting) i can't get it to go to full pressure it will prime up like it's going to go to full pressure give me just a shot of full pressure then go back down to probably half pressure and remain there then prime again for a second then back a coninues cycle! Maybe there's a seal or something somewhere I should look at. Hose and pressure from house is good, the seal whee the hose attaches to the bottom of the washer is ne


This is usually a problem with the "dump valve" defective in not being able to hold the pressure but only able to release it prematurely as it should only do so when to much pressur is built up inline. Only recommend qualified pump tech. But check pu ... Coleman Pressure Washers

I have a Comet BXD 2525 G pressure washer pump which is giving me some problem. (Maybe) I hook the water up to pump and the pressure hose up to the pump, turn on the water and the water sprays out of the water connection at the pump. I check the hose to see if it was clog ok and the next was a the water connection ok. It's like the water is not going int the pump. When i start the pressure up the water come out of gun but no pump running like it should. The next thing i was going to look at i


The water inlet needs a gasket like all hose connections. If its gone the pump may be starving for water. ... Comet Pressure Washers

DuraBuilt 1404. Motor kicks in for two seconds, then quits. High pressure hose blew off and I could barely get it threaded back on. Quick coupler broke so I hooked garden hose up direct. Is lack of quick coupler maybe the problem? Could I be missing a part on high pressure hose that makes it so difficult to thread onto male fitting? Thanks! Bob


... Coleman Powermate DuraBuilt 1400 PSI Pressure Washer

I HAVE A CEAN MACHINE 1210 COLEMAN POWERMATE MODEL # pwo701210 MY PROBLEM IS THE SPRAYER HOSE TO THE PUMP DICONNECTED FROM THE PRESSURE OF THE MACHINE I FOUND 2 PARTS A SPRING AND A LIL BRASS PIECE THAT CAME FROM INSIDE THE ADAPTER NEED TO KNOW IF THERES ANY OTHER PIECES MISSING MAYBE A LITTLE DIAGRAM WOULD HELP SO I WILL KNOW WHAT I NEED PLZ HELP !!!!


Need a repair manual where can I find it ... Pressure Washers

Karcher 2400R I have not used my pressure washer for 6 months. It was left full of gas in the garage. I tried to start it but it would not fire up so I change the gas, oil, and spark plug, took apart the carburator and cleaned it out with carb cleaner. I went ahead and put everything together, pull the cord and wanted to start. While trying to start it after I sprayed starting fluid in the air cleaner I noticed that gas was coming back from the crankcase breather hose into the air filter choking


You have a poor signal to the spark plug usually caused by a rusty fly wheel found underneath the pullcord casing. clean it with releasing ajent such as wd 40. common when not in use for a while. ... Karcher 2500 PSI Pressure Washer

OE Error I'm getting an OE error which is a drainage trouble error. I checked the hose and the drain, and everything is clear. My diswhwasher runs 98% of its full cycle and usually with 2 minutes to go I get this error. I have 2 opinins as to why this is happeneing. 1. Maybe the clog is in my trash compactor, however that seems to be working fine and my sink is funning with no slow down. 2. My 2nd theory is I have to reset the progam within the dishwasher. Like how sometimes I


Had the same problem and had the pump replaced ... LG 24 in. LDF 7811 Stainless Steel Built-in Dishwasher

Assembly plans for karcher 2400 psi pressure i recently had a problem, with my pressure washer. i was cleaning out my hose and took the hose assembly and brass fitting off. run water threw it thought i had cleand it out, put it back together and now when i hooked my water hose back up the water comes out of the despencer instead of the pressure wand. does eny one no what i need to do to revurse this?


... Honda Karcher G2400HH-R Pressure Washer

Shu9925uc/14 bosch dishwasher leaves standing water in the bottom of the pump. The pump seems to be bad because it wont drain out the back hose. I have run the diswasher full cycle and put the drain hose into the sink to test. It wont drain at all now and I dont hear the pump. Perhaps unrelated: Pump seemed to stop working after the back hose disconnected itself from the back of the unit spilling water all over the floor. When I reconnected the unit to the wall the pump now seems to be disfunct


Hi Dishwasher not draining issue occurs due to kinked drain pipe, clogged drain filter or drain pump. Check the drain hose for any visible clogging, remove if present. If no visible lint is present then remove then turn off the dish ... Bosch SHU9925UC Built-in Dishwasher

Low Pressure with no hose attached, pressure is good, attach hose without wand and pressure drops 50%. Have had pump apart 10 times, have checked bypass valve, have even removed bypass and filled passage way so water could not bypass wihout any change. Am down to thinking pump casting is cracked allowing bypassing to happen. Does each of the three piston chambers have a check valve so one piston is not pumping back into another piston chamber?


I worked at a tool rental while attending college and had the opportunity to work on a variety of pressure washers, however, they were of the commercial type. Commercial washers are slightly different in that they usually have seperated components fo ... Karcher 2500 PSI Pressure Washer

I have a Generac pressure washer, model #01450-0, with a Honda 5hp motor. The motor runs fine, but the pressure hose pulsates as if the pump is intermittently making pressure, and the pressure out of the sprayer is about half of what it should be. A friend suggested replacing the seals in the unloader. I bought an unloader kit, replaced everything and it still runs the same. It will build a small amount of pressure, spray for a few seconds, then the pressure dropps to almost nothing. Any help ap


Take a small diameter wire and poke thru the discharge hole of the spray head to clean out.\015\012Second time in 6 months that I had the same problem. The problem is alway in the spray head. ... Pressure Washers

I have a Challenge Xtreme 1800w Upright High Pressure Washer. The proplem is fluctation in water pressure,this even happens when all hoses are removed so the pressure is coming straight from this pump.the vonly way I can describe it is as if it is "hunting"ie high pressure then a ver short pause then back to high pressure. thank you for any advice you can give me with this proplem,also can you recommend a more suitanble machine for home use. Regards M rA C O'Meara


... Pressure Washers

I have a Karcher 330 electric power washer. When connected and set to highest pressure (on variable wand) I get no motor action unless I reduce wand setting, then I get a little boost but not much. If I use high pressure conical wand I get high pressure sometimes, other times motor does not go and no pressure is delivered. I have replaced the high pressure hose.


Just wondering. have you tried it without an attachment to see what kind of pressure you get ... Karcher K2.26 Electric Power Washer

I have a KARCHER Model K 2401 which onstart up has normal water pressure rather than the high. I can usually get it to work by removing the tip, pressing the trigger and running some water through without the tip on. The i replace tip and it will usually retain the high pressure. If I stop depressing the trigger I have to go through these same steps. It is like it loses prime. It works well once I get it started putting out the high pressure.


... Karcher 2500 PSI Pressure Washer

No pressure replaced O rings and seals in pressure pump,now it doesn't work,only hose pressure at tip


Force feed the pump with water it sounds like its sucking air rather than water if no leaks check the 6 valves regards ... Briggs & Stratton Prosumer 20324 Gas Pressure Washer

Karcher 6.85 replaced seals as they were worn out and passing water into the oil now when I turn it on motor runs turning water on water comes out of outlet (which is ok??) but does not pressurize with hose disconnected. My Bosch pressure cleaner passes water through but when pump is started it pressurizes. Is it bypassing? Thanks in advanced


... Pressure Washers

I have two DeVilbiss issues: First, on my pressure washer, I no longer get pressure on "high" mode from the hose. I prime the pump but it doesn't seem to be creating enough force for a high pressure. Second, on my generator, the gas from the gas tank leaks out. The tank is plastic or poly and don't know if it's a gasket issue.


... DeVilbiss Pressure Washer Hose 3600 Psi 25'

I am trying to install a new Maytag MDBH945AWB Dishwasher and have to run the drain hose under the machine in order to get it to the sink. Each time I try to use the hose that comes with the machine it snaps in two and breaks. I have tried to look for a replacement hose that would stand up to the abuse but all I can find is the original. Is there a replacement I can get that is more flexible than the one that comes with it? At this point I am rather embarrased about going back to Home Depot


Hi...home depot sells clear PVC hoses, They come in various lengths up to 100 ft. You can use hose clamps to connect it to the T-fitting. ... Dishwashers

Pressure surges While trying to wash the pressure surges from soft to full pressure then back to soft, and contines to do this. I have as yet to figure this out.


There is a pressure regulator they call a compensator on the pump outlet. Usually, it gets a little sticky and needs to be cleaned or just removed and inspected. It is under the pressure setting cap - it is a plunger with some o-rings - pull it out ... Honda Pressure Washer PSI 3000

Excell vr2500 pressure washer ,no pressure, took off high pressure hose at bottom of washer , get water flow, but flow does not change when engine is running full throttle


Check the water filter ---high pressurehose must have bbackpressure to develop pressure so disconecting it wont acheive ,much ,if you have agood water supply ,oil in the pump--- adjust pressure by srewing the brass fitting that the pressure hose atta ... Pressure Washers

We have a Karcher G2500VH pressure washer. If you start the engine with the trigger pulled on the spray wand it will run at full pressure until you release the trigger. after that, when you pull the trigger it will not have any more pressure than the water hose feeding it. Does it have an internal unloader valve? What is the part number?


Hi, Karcher calls the unloader valve a spill valve, this is a link to a full drawing/parts listing , and your fault description might well be a sticking /seized unloader(spill ) valve hope this helps ... Karcher 2500 PSI Pressure Washer

No high pressure. has been a consistant problem for a while. Was able to get high pressure to "kick-in" before by removing nozzle, squeezing trigger to "prime" high pressure, then quickly put nozzle back in then it would work. now it doesn't work at all.


See this link to fix the problem ... Honda Karcher G2400HH-R Pressure Washer

Karcher K386M-I was using the washer and the pressure hose popped off the outlet of the unit. I put it back on and it popped out again. The second time I noticed the oring was gone. It was on there when I first put the hose on. Why does the pressre hose pop off.It was on tight?


... Pressure Washers

Let go of wand trigger pressure will not come back


Spill valve is stuck and needs to be cleaned and greased common problem....also check all connections for blockage in line ... Karcher 2500 PSI Pressure Washer

I have a Danby Dishwasher model # 67638 18052. There is a slight crack in one of the parts underneath that is allowing water to leak out. The part is located in the back corner and it is a pale yellowish elbow shaped connector. Can I get some some kind of glue to seal it, or do I need to get it replaced? It that going to cost a lot? Is it going to be worth it?Thank you for your time.


... Danby DDW1805W Designer Series Free-Standing Dishwasher

Cycles - pressurizes when trigger is pulled, then motor sets back to idle immediately as if trigger is let go, but is still engaged. Pressure and idling happens within 2 seconds, continously cycling


A lot of commercial and industrial grade pressure washers especially have a safety feature that will either shut down or will return the motor to idle if you do not have an adequate supply of water to the pump to protect the plungers and valves from ... Coleman Pressure Washers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1323 seconds