Having problems with your Coleman Pressure Washers ?

I need a Gas tank for a Powermate 2000 washer pump model PW0832000.02. Where i can get it?


Answers :

After extensive searching the best I can come up with is to call coleman tech support at 1-800-279-9274 and explain what it it you need. This appeares to be an obsolete model as I was only able to locate parts for sprayer wand. Hope this helps you some. Thank you.
Repair Help & Product Troubleshooting for Coleman Pressure Washers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I need a Gas tank for a Powermate 2000 washer pump model PW0832000.02. Where i can get it?


After extensive searching the best I can come up with is to call coleman tech support at 1-800-279-9274 and explain what it it you need. This appeares to be an obsolete model as I was only able to locate parts for sprayer wand. Hope this helps you so ... Coleman Pressure Washers

I have two DeVilbiss issues: First, on my pressure washer, I no longer get pressure on "high" mode from the hose. I prime the pump but it doesn't seem to be creating enough force for a high pressure. Second, on my generator, the gas from the gas tank leaks out. The tank is plastic or poly and don't know if it's a gasket issue.


... DeVilbiss Pressure Washer Hose 3600 Psi 25'

I have a model PW 2200 gas pressure washer. It suddenly lost it's high pressure the other day after working fine for @10 minutes. It's getting plenty of water, but the engine doesn't seem to rev up to give it the high pressure. The operating instructions say to check the oil in the engine, and the PUMP before starting, but I haven't found any place to check for an oil level in the pump????Any ideas, I'm very confused.


... Pressure Washers

I have a excell 2500 psi max honda 5.5 ho vr2522 2.2 gpm presser washer and has been stored for about a year, still looks brand new and has only been used twice before, it has oil and was stored with no gas in the tank, i put fresh gas in the tank and blead the fuel bowl until fuel ran out like it should, the washer wont start, ive checked the turn on switch as well and the fuel cut off knob, i spayed gas in the carb and it fired up but stopped running as fast as it began to run, its not getting


... Honda Black Max 2600 PSI Pressure Washer

I have a Karcher 2,600 PSI 2.3 GPM Gas Pressure Washer G 2600 VHR that I have used once last summer. I have stored the PW in my basement with no fuel in the gas tank. The PW was never exposed to freezing temps. I cannot get the PW to start. I put new fuel into the tank, the oil is good, I drained the carburetor, and the spark plug works (tested it). I pull the cord and the engine doesn't turn. Fuel value is on, choke is pulled, and the starter switch is turned on. System is practically brand new


Hi I have a similar pressure washer from Kartcher and the same scenario as yours I have owned it for about 2 years and noticed that it was getting harder and harder to start with each time I use it which is months. If your pw has a honda engine on i ... Karcher G 2600 VH Gas Pressure Washer

Re: Creaftsman 2700 psi washer, model 580.752100 - I cannot use the detergent cleaning tank. The pump forces water into the tank, and it overflows onto the ground. If I try using the washer with the detergent shut-off value in the off position, the water pressue forces the valve completely out of the housing. Is there a simply fix for this or time for a $ervice call? sw


... Craftsman 2700 Max Psi Pressure Washer 23 Max Gpm

I am trying to get the pump info. for a north star power washer. All the info. I have is ser. # 157346-0698 2777 The pump is a Admiral model xlg 3035 m I need the gpm,psi for this power washer. Thanks for all your help Wayne


... Pressure Washers

Briggs and Stratton Troy Bilt gas pressure washer one year old. I can get water thru pressure washer and bleed the air, water comes out the hose just fine until I start the pump. Then, I lose all water flow. Pump runs fine but when it's running, no water goes through.


... Briggs & Stratton Prosumer 20324 Gas Pressure Washer

Hi ..I have an Excell gas pressure washer model no. Exwgv2121-3 with Faip 2100 psi 2 gpm vertical shaft pump..the problem is that there is water leaking from every weep hole at the bottom of the pump when running. Oddly enough,the pump still puts out significant pressure but less than it should due to the leaking water. What is the most likely cause of this?..is it the high pressure water seal(s)? If so,how do I repair it?


... Pressure Washers

Unable to start gas engine on a NorthStar pressure washer


Disassemble and clean the carb. If it ran briefly with the starer fluid then gasoline is not coming through the carb. ... Northstar Pressure Washers

Maytag Dishwasher Model MDB4100AWQ When I start the Light Wash Cycle: Washer fills with water, heater comes on (I checked it with a volt meter--120 volts), timer runs, motor never runs, before the timer gets to "rinse" the heating delay light on the door comes on and the timer stops. The heater is still on (120volts) nothing further happens it just boils away on the water in the washer. Note: If I manually forward the timer to "rinse" the motor will kick in and run but does not pump out w


Most common d/w power is 120 volts, check for 120 volts with a  ... Dishwashers

The Hom Model No. 308653045 gas-operated cold-water pressure washer has a spring-loaded control on it and I am assuming that this control regulates the output pressure of the water from the pump . . . for example, 1500 psi to 2700 psi. Is it correct to assume that this control regulates the output pressure of the pump. If the control is a pressure regulator, how does one use it and, EVEN MORE IMPORTANT, can one under-adjust or over-adjust the control to a point where THE CONTROL OR THE PUM


... Homelite Pressure Washers

I can't get the igniter to start on north start pressure washer #157224. Fuses ok, indicator light in heat switch does not illuminate. Blower works, fuel dripping out. Cleaned fuel tank and pump and filter too! Tried jumpering past the thermostat didn't help either. Also, swapped pump and heat switches on main panel. No help!


... Pressure Washers

We have a commercial Hobart dish washer Model # AM-8T2; Serial # 240461. We cannot get the wash temperature to go above 120' to 150' as the burner does not light. The pilot is on. A new thermocouple was installed but made no difference. The rinse temp goes up to 180'. How can we get the gas burner to light and stay on. Thank you. Gery Spory


Hello Gery - get the repairman back who installed that thermocouple as that repair includes making sure the unit is working properly. Most likely the thermocouple is simply not warming up enough to operate correctly. It may be that the pilot light ... Hobart Dishwashers

Water Diver Series pressure washer, model WGV1721 shut off when running and the pump gets so hot I can't keep my hands on it.


... Briggs & Stratton Pressure Washers

I have a Ryobi power washer with subaru motor, model #RY30080. I bought it 3.5 years ago. I only used it one time as purchased. This summer,it did not start. Yes, I left gasoline in the unit. I did not know that it require to drainout the gas prior to winter storage. Help, what can I do to get this machine starting again. Used only one time.


... Pressure Washers

Not getting gas engine tank - Honda Black Max 2600 PSI Pressure Washer


... Honda Black Max 2600 PSI Pressure Washer

Have a honda 5.0 hp engine on a pressure washer model belive is a de 1504 not sure of make, starts if you use starting fluid but then dies, getting gas to the bowl at botttom of carb but not to carburator


Hi there mburns44 i believe your problem is either that either the Air/Fuel mixture is too rich and causing it to flood or you have clogged jets. carburators are tricky and often times need to be cleaned or adjusted by a professional. I hope that thi ... Devilbliss DeVILBISS Devap DVH2600 Gas-Powered Pressure Washer

No water is getting inside my Bosch dishwasher compartment. Water supply to dishwasher is ok. Checked hose at input of dish washer and water supply is ok. Could pump have packed in? Model 004 920 378. Dishwasher used daily since 1999.


Normal\012 0\012 \012 \012 \012 \012 \012 \012 MicrosoftInternetExplorer4\012 \012\012\012\012\012\012 /* Style Definitions */\012 table.MsoNormalTable\012\011{mso-style-name:"Table Normal";\012\011mso-tstyle-rowband-size:0;\012\011mso-ts ... Bosch Dishwashers

I have a Karcher G2600 OR Pressure Washer, 2600 psi, 2.5 gpm. PN 1.194 506 0. gas engine works fine and water flows fine but pump is not adding pressure to stream. Checked and cleaned inlet water filter.


... Pressure Washers

I have a B&S 3.75, model 98902,type 014301,code 96032254 gas engine which powers a 1500PSI Clean Master power washer. The engine will start if primed but will not continue to run unless fuel is sprayed down the throat of the carburator.Apparently a gumedup/dirty carb. what is the best way to proceed to clean it? Where is best place to get a rebuild kit and/or replacement carb if needed? What are other possibilities if not a dirty carb?


... Pressure Washers

I have a craftsman Pressure washer Model 580-725400 the unit has ran great until today. I last used the unit 1 week ago with no problems but now I have to run the machine almost full choke to get it it rev up and run smooth. The engine oil is clean and filled to the proper point. The spark plug is new and gapped proper. The air filter is new also. And the gas is 97 Oct and fresh. When it choke it to crank the engione I move the choen to run and the engine struggles to run. When I move the choke


... Craftsman Pressure Washers

I was given a low hour, 10 year old, CH PW205002LE 6.5 HP gas vertical shaft 2000 PSI/2.5 GPM pressure washer with a Lavor pump. It did not work - no pressure. I found a broken o-ring on the brass unloader valve and replaced it with a ring as close in size as I could find as the part break down doesn't state size. Everything was very clean. I coated everything with silicine grease and reassembled, seating the brass piston? as deep as it would go. I had to press the trigger in order to get the mo


My personal experience is that 40% of all the sellers I dealt with on e*** exaggerated their products or worse. If you decide to go the e*** way be sure you put it on a good credit card so you can get your money back if it's a bust. Don't use your ba ... Campbell Hausfeld Pressure Washers

Pressure Washer I have a Porter Cable pressure model no.PCH2401.It works fine for 5 minutes,then I can hear the motor loading down and then it stalls out. I tried to start it and it was very hard to pull on. disconnected the water supply and if was very easy to pull and started right up. I noticed the pump was very hot.This unit has a thermal relief valve on it,shouldn't it have released when it gets to a certain temperature .I was thinking maybe this is why it might be shutting the motor


Any leaks from connection at pump to gun and wand assembly if so the valve is detecting leakage and open up again without u squeezing trigger it builds up in the head.if your trigger gun is leaking internally then you will need to replace the gun thi ... Pressure Washers

Where do i get a new pump in orlando fla - Devilbliss DeVILBISS Devap DVH2600 Gas-Powered Pressure Washer


... Devilbliss DeVILBISS Devap DVH2600 Gas-Powered Pressure Washer
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1790 seconds