Having problems with your Comet BXD2527 Pressure Washer Pump ?

Comet pump will not release from gas engine. Can you help? Thanks


Answers :

Sometimes you can put the bolts on the pump loose and run the machine. The vibration from the motor will work the pump loose. If you do that, remove the brass head or the pump will overheat.
Repair Help & Product Troubleshooting for Comet BXD2527 Pressure Washer Pump

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Comet pump will not release from gas engine. Can you help? Thanks


Sometimes you can put the bolts on the pump loose and run the machine. The vibration from the motor will work the pump loose. If you do that, remove the brass head or the pump will overheat. ... Comet BXD2527 Pressure Washer Pump

Assembly I recently purchased a pressure washer from Home Depot. It is rated at 3100 psi. It is a comet pump with a honda gas engine. The assembly instructions recommended that I remove the plug on the top of the pump and replace it with a vented plug that was provided. However, none of the other enclosed manuls talk about the vented plug. Am I reading the assembly insturctions correctly. Should there be a vented plug ?


HI your machine would have been delivered with a blanking plug in the pump. You will need to remove this and fit a vented pump or your pump will build up too much pressure inside. ... Comet BXD2527 Pressure Washer Pump

Got a Dewalt 3800 PSI Pressure Washer with 4.0 GPM with a Honda GX 390 gas engine. Tipped it up to roll it out to my truck and got a big puddle of water with what looked like Pump oil in the puddle. Can you help???? It is less than a year old with 10-15 hours on it.....


Could very well be. Did you check the oil level and condition of oil? If its too full or if its light brown milky, then water has entered crankcase. Pressure washer pumps cannot stand to ever let run dry. Even a little. Also excessive idling will ov ... Dewalt 3800 PSI Pressure Washer

I just bought a used and broken Power Washer which I plan to repair and use, hopefully. I can't seem to locate operators/parts manual. NorthStar Pressure Washer ? 2400 PSI, 2 GPM Item#: 157472A Serial #: 1106 4728 Bar Code: 157472A11064720 Engine: 6 HP Tecumseh Pump: Comet VRX with brass manifold and stainless steel plungers Drive: Direct Thanks for your help.


... Northstar Pressure Washers

I have a Briggs & Stratton gas power washer. This is the 1st time this year that I have used it. I put in fresh gas, hooked up the water supply. The engine started and then quickly stopped. I had to release the water pressure in the hose before I could pull start the engine. The only way to keep the engine running is to hold down the spray nozzle trigger. Once that is released the pressure in the hose builds up and the engine stops.


Sounds like the unloader is not working correctly. Try replacing it and see what happens. ... Briggs & Stratton Prosumer 20324 Gas Pressure Washer

DeVilbiss Pressure WAsher EXH2425 Honda engine GC160qha pump DAPC axcial cam. When using washer sprayer both the engine and pump seem to operate normally. As soon as I let off the trigger of sprayer the engine dies. Help?


Hi and welcome to FixYa. I am Kelly \015\012Take a look at your engine parts manual here: \015\012\015\012 ... Pressure Washers

I have a model PW 2200 gas pressure washer. It suddenly lost it's high pressure the other day after working fine for @10 minutes. It's getting plenty of water, but the engine doesn't seem to rev up to give it the high pressure. The operating instructions say to check the oil in the engine, and the PUMP before starting, but I haven't found any place to check for an oil level in the pump????Any ideas, I'm very confused.


... Pressure Washers

No pressure Gas powered pump is a radial type from DeVilbiss. There is very low pressure, although there is some pulsing from the pumping action. There are no leaks and the supply pressure is good. Pump pistons are in good condition. They seem to be pumping when I had it disassembled and operated by hand. I suspect it is something in the bypass or unloader. Or it may be in the ''easy start'' assembly which I assume reduces backpressure on the pump when starting the engine. Pump has a temperatu


... Pressure Washers

Troy-bilt w/ rmv2.2g24 pump and honda gvc 160 engine fires but will not run until I remove the pump-pump turns by hand but is very stiff, can you help me ?


... Karcher 2500 PSI Pressure Washer

Engine dies every time i release my trigger the engine dies it is like the bypass isn't working the engine starts great and the pump works fine


... Pressure Washers

Leaking cap screw on pressure washer pump - General Pump EZ4040G Pump 3400rpm Direct Mounted to Gas Engine Shaft with 4 Bolts


... General Pump EZ4040G Pump 3400rpm Direct Mounted to Gas Engine Shaft with 4 Bolts

I bought this dishwasher 5 years ago and was kept in the box until last month. I installed it, turned on the water and no water is being pumped into the unit from the water release valve in the dishwasher. I then checked all the cycles and everything works except for the pump. Then I checked to see if any power/volts was going to the pump and there is none. Could it be a wiring problem or could it be the circuit board?? please help. thanks


You will have to check all the connections visually. Since you know how to use a meter, see where the current stops. See if there is current coming from the control board to the pump. the water inlet solenoid valve should "free flow" water into the m ... GE 24 in. Profile PDW7800 Built-in Dishwasher

My Karcher K3.48M pressure washer remains in the low pressure mode even when I return the pressure nozzle to the high pressure position. How can this be corrected. The pump seems to build up the pressure because when I release the handle the pump motor stops. This is a fairly new pump which was purchased in the latter part of last year(2010). Could this have been caused by the detergent I have been using which is an automotive shampoo? Please help I love this washer and for the times that I u


... Karcher PSI Electric Pressure Washer

I have a gas powered husky 2600 psi, hook up everything 3/4 hose line about 10 ft long, let water flow through w/o nozzle added, fire up the engine and when I pull the handle, engine stalls out . Any help would be great, mike


Choke off? \015\012Fuel quality, meaning no water, is essential of course.\015\012If its brand new and this is the first starting, I would call Husky. Check oil..\015\012The engine has a governor on it, so it should be sounding lik ... Pressure Washers

I have a Simoniz S2800, it will only start with the trigger depressed to release the pressure and when it starts the engine seems laboured and there doesn't seem to be the ame pressure as it used to have, also if it isn't used after a min or so it will release water pressure from the bottom, do I need a seal kit or a pump kit to correct this problem.


Where is the unloader valve on these machines? ... Pressure Washers

Pump Issue I have a john deere pressure washer. I hook the hose up to it, rurn the water on and no water comes out of the wand. I started the engine briefly and pulled the trigger on the wand and still nothing. The model number of the pump is Annovi Reverberi SJV 2.5G24-1. I can't seem to find any info on the G24? There is info on the G27-1. Not sure what to do here? Please help.


... Pressure Washers

My 5.5 HP-GX160 HONDA ENGINE Will run only the amount of starting fluid/gas in the carberater ! With aircleaner off ! I drained the gas and put new gas in! it starts so it has spark! PLEASE HELP??????


... Pressure Washers

I HAVE AN EXCELL PRESSURE WASHER-MODEL EXPRO 2530-HONDA ENGINE GX200QX2-IT HAS A CAT PUMP MODEL#2SFX30GZ1. IT IS VERY HARD TO CRANK UNLESS YOU DEPRESS THE HANDLE ON THE SPRAY WAND WHILE CRANKING.ONCE STARTED IT WORKS FINE UNTIL YOU RELEASE THE HANDLE AND THEN THE ENGINE QUITS.IT DOES NOT GO INTO BYPASS MODE.


... Caterpillar Cat Pump Pressure Washer Pump 3SP30G11

I have a Baldor 6000W generator with a gx340 11hp engine. I have drained the tank and carb and put new gas and sea foam in it. Also I have replaced the spark plug and fuel filter. The engine will start/run as long a I spray starting fluid in the carb. But it will not continue to run without it. Also I just checked the oil level and that is good. Please help!!!


It sounds like the engine is not getting enough fuel for it to run. First check that you have the fuel tap in the on position. If the fuel tap is on then the carby might be blocked or the needle & seat are not working properly. Turn the ... Honda 8 HP Engine

I have a Neff dishwasher S6409N1GB/09 and for the last 3 months engineers have been out to fix it but it still does not work. They have fitted a new motor, new pump, new circuit board, new fill tube, new breather, can you advise what the problem could be, because the engineers have given up on it, help. Mr Dave Gallagher


... Neff Dishwashers

I have a Honda ,gas powered power washer and when I squeeze the handle the water pump kills the motor. I've let the engine run until warm and it still can't take the water pump engaging. It's a three year old washer.


... Pressure Washers

Karcher engine still run's when gun trigger is released, as if the trigger is help down. Model K2.080


... Honda Karcher G2400HH-R Pressure Washer

Changing oil on a high pressure washer with Comet Water Pump


... Comet BXD2527 Pressure Washer Pump

I have a Karcher g 2500 vh gas pressure washer and I can't find what oil to use when changing the engine oil. It's not in the owner's manual that I down loaded and I'm not able to find this info on the internet... Can you help?


... Pressure Washers

I have a Karcher G2600 OR Pressure Washer, 2600 psi, 2.5 gpm. PN 1.194 506 0. gas engine works fine and water flows fine but pump is not adding pressure to stream. Checked and cleaned inlet water filter.


... Pressure Washers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1134 seconds