Having problems with your Comet Pressure Washers ?

Power washer problem no pump action

\015 No pump action also water when turn on seems like it back up and comes out of water connection also no water out of wand. I start pressure washer and no loud pump noise and water still comes out of connection spray out. Its 4 yr old but only used about 8 times. Need help!\015

Answers :

Sounds like nozzle is blocked.small bits of grit jam nozzle unscrew and make sure its clear turn water on and pull trigger to see if gun trigger works,then refit nozzle check again for spray.if clear start up and try out.if no go then pump probably needs cleaning and relubing seals.
Repair Help & Product Troubleshooting for Comet Pressure Washers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Power washer problem no pump action

Sounds like nozzle is blocked.small bits of grit jam nozzle unscrew and make sure its clear turn water on and pull trigger to see if gun trigger works,then refit nozzle check again for spray.if clear start up and try out.if no go then pump probably n ... Comet Pressure Washers

My Delonghi Dishwasher keeps turning off. The dishwasher is turned on at the power point. The water is turned on. Okay When I press the POWER botton on the front it wont stay on. I have to keep my finger on the POWER button and then press the START button for washer to work. If I do this it will then pump out any water in the bottom and start to work. ***BUT when you take your finger of the POWER button the washer just turns off and stops working. Do you have any idea what could be the problem p

Yes, the power button is faulty. by pressing the power button forcefully, you are in effect allowing the contacts to close. Replace it. ... Dishwashers

I have an Electrolux EIDW 6105GB1. The washer fills with water then immediatly drains back out, the lights all flash and the trouble code light under the kick panel indicates the wash pump. It has done this before and I took the pump out and checked it with power direct, then returned it to the main control board plug and it was working and pulsing it's speed as it should. It worked fine for several weeks and now it's doing it again. Is it possible that there's a problem with the water float ins

Hi\015\012\015\012The issue is either with the wash pump that is going bad or\015\012the motor itself that is unable to run. As the washer fills and then drains\015\012immediately so the pressure/float switch should also be checked. Hope ... Electrolux EIDW6105GW 24 in. Built-in Dishwasher

Pump appears to be shot in Generac 2.3 gpm 6hp Briggs-powered pressure washer. Anyone know how to diagnose pump problems?

Mine blew up. The OEM is ****. Went on-line to buy a similar but more powerful pump. There are lots of pumps that are an easy bolt on. It's mostly standardized. Google "pressure washer pumps" ... General Pressure Washers

Our craftsmen electric pressure washer stopped working while in use. We have power - red light on gfci and we tested the master switch - has power too. So what can be the problem? One post mentioned a jammed pump switch. What is that and where is it? We used it 2 weeks ago and it worked fine.

The pump switch they spoke of is an internal switch. It is activated by a valve so that when you let go of the trigger, the machine shuts off. This valve is stuck or the switch is bad. Usually the valve is the problem. I would go to Sears and get ... Pressure Washers

I have gcv 160 5.5 hp power washer my problem is that the high pressure pump is not working properly when the engine is running the output pressure is very low so i would like to know could be the possible cause of that problem

look for a black plastic cover with a silver snap on top; pry off the silver snap and lift off the plastic cover; next remove the two screws on the top plate then pull out the piston inside - if unable to lift out, start unit and watch it pop ... Karcher 2500 PSI Pressure Washer

Pump Problems When i engage the pump on my power washer the motor dies what can i do to solve the probblem? Solutions please

... Karcher 2500 PSI Pressure Washer

I have a union power petrol pressure washer up1-50 I am having problems with a fine spray of water coming from the 1st brass screw on the end of the pump and keep loosing pressure

I have the same hair line crack so water pushes out the top. Can the part just be replaced ? ... Pressure Washers


If you want to run a very small amount through the engine to help clean carbon deposits I would say that was fine as long as you only used 1-2 ounces to the gallon. But if you want to run diesel through the pump itself I would not recommend this. ... Pressure Washers

Whirlpool dishwasher, model DU1050XTPQ1, type 575-0; problem: showing no sign of power to unit and bottom of dishwasher is full of water---it apparently stopped during cycle. Is there a reset button? I have tried depressing the front panel "lock" button for five to ten seconds to unlock the system with no luck. The washer is hard wired to the home electrical system. What should be my next course of action? Thanks

... Whirlpool 24 in. DU1050SS Built-in Dishwasher

So I found this power washer for sale. The seller claims that the washer generates a good stream of water, not just full power. He also mentions that after a few minutes the engine starts to bog down like it is working extra hard. Does this sound like a pump issue? Could something be clogged or would the pump need to be replaced? Or should I avoid this power washer?

Don't buy a power that doesn't work.There are many expensive parts on a power washer. If it was cheap and simple to fix, the seller would fix it and the washer would not be for sale.Would you buy a car that doesn't work? Especially ... Pressure Washers

I am trying to get the pump info. for a north star power washer. All the info. I have is ser. # 157346-0698 2777 The pump is a Admiral model xlg 3035 m I need the gpm,psi for this power washer. Thanks for all your help Wayne

... Pressure Washers

I have a Honda ,gas powered power washer and when I squeeze the handle the water pump kills the motor. I've let the engine run until warm and it still can't take the water pump engaging. It's a three year old washer.

... Pressure Washers

Miele Diamante G 2150 SCU Dishwasher problem ----The program cycle indicators "Rinse", "Drying" and "End" flash at the same time. The drain pump is running when the door is open. I have reset the power and cleaned the drain pump and non return valve and Spun the propeller several times in both directions to check for obstructions. Still has the same problem. Water is being drained continuously even with power switch on dishwasher turned off.. Had to shut the breaker off to get it to stop. A

Hi\015\012\015\012Plugged system or a jammed drain pump can cause these issues, also make sure the drain hose is not blocked. Check the drain hose for any visible clogging, remove if present. If no visible lint is present then remo ... Dishwashers

Asko dw20 pump keeps running even with door open and turned off... The machine got to the final cycle then the pump just keeps running and the glass icon (L2) keeps flashing. All the water is not evacuated from the washer. When I power off from the front the drain pump still runs (and water is still not draining). When I power cycle from the mains (waiting 10 seconds) the pump engages again and the water level drops a bit and then stops draining. I have done this until all the water is empty an

... Asko Dishwashers

My Bosch Dishwasher does not drain all the water out of the dish washer after the finishing cycle...I usually start the washer and then push the drain cycle and it starts to pump for about 10 seconds and stops and starts and pumps again for 10 seconds and stops and then pumps for about 25 seconds and stops....doing this manual drain twice empties the dishwasher of the excess water....what may the problem be?

... Bosch 24 in. SHE43C05UC Stainless Steel Free-Standing Dishwasher

Dishwasher model# FGHD2433KBI. washer was purchesed mid July, used 4 times. I just put in some dirty dish's and closed the door. A couple minutes later the washer turned on. No lights were on. After a few minutes I pushed the cancel button. Nothing happened. I opened the door and it sounded like a sucking sound and the pump stopped. No water in unit. I closed the door it started again. I cut the power at the circut box. Waited a few minutes and turned power back on. Power failure light came on.

... Frigidaire 24 in. PLD2850 Built-in Dishwasher

Hi my L G dish washer is coming up with E1 . It comes on after about 2 min it takes water into the washer then it hummes for about 30 seconds then comes up with E1 and pumps water back out. I have checked the hoses which don't appear to be leaking -I read somewhere in your answers about this problem that it could be the Water Level in Drum lowering, this means there is a leak on one of the pipes. More likely it is the Circulation Pump, which is responsible for pushing the water to the Spray

Hello aderry -\015\012\015\012\015\012I'm a bit short of time as I'm on my way out to a service call, but I've uploaded the service manual to Rapidshare for you to download. \015\012\015\012\015\012Rapidshare download inst ... LG Dishwashers

I have a problem with my Asko D3350 Dishwasher, can you help? On startup the diswasher does its normal cycle and pumps excess water out and then fills the dishwasher with water to the correct level of water, after this the machine has no dishwashing action at all for the duration of the program setting. The dishwaher then pumps all excess water out and switches off as normal but no washing action has taken place, there are no error codes during the entire operation. Is there any way to rese

Hi Tony,\015\012\015\012I have the same machine (D3350) and almost the same problem.\015\012\015\012Mine starts each cycle fine - pumps out - fills - rinses - pumps out tht first load and then does not fill again. If I manuall ... Asko Dishwashers

I have a McCulloch FH160B power washer and it no longer builds up pressure. I haven't used this very much at all. I tore it apart and cleaned everything I could find. When i pull the trigger for the spray nozzle, I get line water pressure. When I release the trigger, the power washer sounds like it starts to build up pressure. When this was working correctly, the pump would shut off when the trigger was released. Any suggestions?

... McCulloch Pressure Washers

Pump problems we have a mobile car wash service that we use in the winter months we have a 300 gal tank and several power washers.we use 3 diffrent machines [email protected] gal 2500 [email protected] and a3000psi @3.0 gal i;m having a lot of pump problems with all of these machines.a friend that he thinks that the hose that the machines feed of is to small 3/4'' he suggests i use a1 1/2 hose as close to the machine before adapting to the 3/4'' fitting right now it;s about12'' long away from the tank.any info wo

Are you only using gravity to feed the machines. The law of gravity is that, for every foot of elevation you will get 2 PSI ( pounds per square inch) of pressure. You can figure out the minimum volume that the manufacture requires and make sure that ... Comet GXD2527G Pressure Washer Pump

Comet power washer 2325 ---- Honda 5 hp psi 2,500, gpm 2.30

... Comet Pressure Washers

No pressure Gas powered pump is a radial type from DeVilbiss. There is very low pressure, although there is some pulsing from the pumping action. There are no leaks and the supply pressure is good. Pump pistons are in good condition. They seem to be pumping when I had it disassembled and operated by hand. I suspect it is something in the bypass or unloader. Or it may be in the ''easy start'' assembly which I assume reduces backpressure on the pump when starting the engine. Pump has a temperatu

... Pressure Washers

I have a Comet BXD 2525 G pressure washer pump which is giving me some problem. (Maybe) I hook the water up to pump and the pressure hose up to the pump, turn on the water and the water sprays out of the water connection at the pump. I check the hose to see if it was clog ok and the next was a the water connection ok. It's like the water is not going int the pump. When i start the pressure up the water come out of gun but no pump running like it should. The next thing i was going to look at i

The water inlet needs a gasket like all hose connections. If its gone the pump may be starving for water. ... Comet Pressure Washers

Troy-Bilt 2550 20293 pressure washer not producing pressure. Worked when last used 2 months ago. Pump pistons are moving up and down when engine is pulled through. Inlet water is flowing through pump but no pressure when engine is started. I have the same problem. Water flows thru the pump when not running, but no flow or goes in by-pass mode when I start the pump. The pump being Troy Bilt Model 020296-01. I replaced unloader valve even. Anything else I can do?

You replaced the unloaded valve. Are you positive you have the unloader screwed to pressure and not turned the opposite way? You will have no pressure if it is adjusted wrong. One other thing I have encountered is that the unloader has a ball bearing ... Pressure Washers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0837 seconds