Having problems with your Comet Pressure Washers ?

When i start the machine runs for 5 sec and stops.


Answers :

Check your air filter, its probably clogged. remove it and start. if it continues to run, the filter needs to be replaced.
Repair Help & Product Troubleshooting for Comet Pressure Washers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Good mroning after starting any program first the pump will run followed by water intake. After a while the machine stops and the light intake/drain starts blinking. Most of the time water will stay in the machine. After pressing the on/off bottom first switching the machine on again and starting a new program the machine pump start running emptying the water but than stops after a short water intake again. I opened the water stop but it seems to be ok. The filter inside the machine is cle


Good morning don't get shocked because ullu ki to abhi subah hi hui he ... Miele 24 in. G892SCU Plus Built-in Dishwasher

Smeg dishwasher model DI 612 C type 12053 good morning After selecting a program and shutting the door the drain pump starts and runs for 2 seconds then stops. The machine makes a bleep noise then the drain pump starts again running for 2 seconds then stops again and the cutting in and out process continues and the machine never reaches its selcted cycle. No alarm lights are displayed. I have filled the machine with water so that the filter is submerged and the level is


... Smeg Dishwashers

When i start the machine runs for 5 sec and stops.


Check your air filter, its probably clogged. remove it and start. if it continues to run, the filter needs to be replaced. ... Comet Pressure Washers

Candy washing machine runs through programme and stops at the point where it drains the drum to start the spin. Have switched it off and turned timer to correct position and it drains and spins OK (1200 spin) Tried other programmes on timer but same thing, stopping at point where the pump drains and the spin starts. Have checked the pump and is OK any ideas please, I am quite capable of taking the machine apart for repair. Thanks in anticipation Pete


... Dishwashers

ETNA ENF 18500A/5 type: 3.E1.181213221110 36 VLENNL 5 Dishwasher lights are on, and set for running, but the dishwasher does not do anything. Sometimes it makes a slight hum when closing the door, but most of the time, nothing. It stopped running after standard dish washing liquid was put into the machine by mistake. At that time, the machine started and ran through part of the cycle, but did not complete, and did not drain the water. Since then it has not started again. I have remo


... Dishwashers

I have a Honda GC160 5 horsepower power washer with 2400 psi. When its cold it is easy to start but after it has been running for a while the only way to start it is to have the water shooting out of the wand. Once it is hot and running if i stop the stream of water (release the trigger on the wand) then the machine shuts off. It seems like the only way to keep it running is to constantly have water running through the wand. Please help


... Pressure Washers

ADP5550 DISHWASHER RINSING LIGHT ON, START LIGHT FLASHING TWICE, BUT STUCK WILL NOT PROCEED WITH THE WASH. I HAVE PRESSED THE START BUTTON FOR 10 SECS, 30 SECS BUT THE ONLY RESPONSE IS THE PUMP ONLY RUNS FOR A FEW MINUTES AND STOPS.


This does sound like a problem with the "anti-flood" device that does detect water (leak / spill) at the base of the washer. This device is a protection device that consists of a polystirene float and a micro swithch. Once a water leak od spill is de ... Whirlpool 24 in. DU920PW Built-In Dishwasher

Program stops When the machine is switched on it runs for a minuite or so then stops and bleeps and shows blanks - - - - I switch it off and again re-start and it again repeats this as above the filters have been cleaned and the water was drained and again it persists, the machine is 3 yrs old. I tried a sequence described as switching the programm button in 4 quick times but this didnt work either. Is there any other way we can re-programe this dishwasher or is it that there is a fault where so


... Smeg 18 in. DWD409SS Built-in Dishwasher

GE GSD6610GOOB not cycling properly. Our dishwasher is about 6 years old and has been nothing but trouble the past year or so. We've already paid too much money repairing it the first time, (it simply stopped working - the control panel was totally dead) and don't want to pay anymore. Current problem - the machine starts up and fills with water and it sounds like it's running OK, then it will just stop, sometimes for a couple of minutes sometimes longer. Then it will start up again - and


... GE 24 in. GSD6600G Built-In Dishwasher

Hello, I own a Honda Pressure Washer (Porter Cable Model) with a Cat pump 2600psi and 6.5 hp. An Excellent machine for the past 7 years. Last fall I noticed it was not producing the full pressure but still Engine was running strong. This past weekend. started it up and used it for about 1 hour still with minimal pressure at full throttle. Then pressure was totally cut off. I stopped and started the engine the engine and it had minimal pressure again. Same thing happened again. I stopped the engi


... Honda Pressure Washers

Whirlpool ADP 4501 problem. Starts normally andthen after 30 secondes or so begins to 'pulse' ie pump runs briefly then stops and the power 'start' light flashes with each pulsation. No water coming into machine, seems to be trying to pump out but stopping


Sounds like electronic module failure if there is no water in machine. ... Whirlpool Dishwashers

My 1yo slimline hotpoint dishwasher LST216 has developed a fault when trying to run the 'normal wash': washing stops after a couple of mins, the lights start flashing and the alarm comes on as soon as the water is being drawn into the machine. When I open the door I can hear a whirling/grating motor noise coming from the bottom of the machine. I have cleaned all filters and have run other programmes to check overall functionality and they all work as expected most of the time. I cannot unders


... Hotpoint Dishwashers

Our dishwasher came with our house. Brand new. It is 2 yrs old now, warranty gone. The problem is when you shut the door the machine starts running immediately and keeps running and running and running. You can push the stop button, delay button and it still runs. Also, doesn't clean. model# FDB1050REC4


... Frigidaire 24 in. FDB1050RE Built-in Dishwasher

The start/pause button beeps when pressed to start a program and the machine gives a beep in response and appears to start its initial sump emptying phase but stops within 1-2 secs. Have checked pump and found no problem but start time is so short that in cannot have sensed a problem in the pumping circuit. If I persist in holding the start/pause button in, it can be released after the initial sump emptying phase (2-3 mins) and phase 1 of the wash program goes to completion. At the end of the


Hi\015\012\015\012Ronald...the beep sound itself indicates an issue with the\015\012membrane switch (control panel) and it should be replaced. I believe that the\015\012pump and motor is fine as its just beeping and doing nothing else. Ho ... Smeg 24 in. DWI612 Built-in Dishwasher

My dishwasher skips the final drain cycle. The lines are all clean and there is no clog. It drains just fine in the beginning of the wash cycle. Every time I do a load of dishes I have to run the full cycle, then leave the machine open for 3-4 hours and start the cycle again and listen for the drain at the beginning of the wash to drain the machine from the initial wash and stop the machine after it is done draining so it won't fill up again. Sometimes we have to unplug it and wait about an hour


... GE Nautilus 24" Built-in Dishwasher

Hi - I have the Miele G 2470 dishwasher. It starts, and I have it set at "2 in 1 Tab" and on "Normal". I close the door and the machine makes a sound like it is starting, but then after abiut 30 seconds it starts alarm beeping and doesn't run. When you open the door it shows the light is now on next to "Intake/Drain". To stop the beeping I have to press the "off" circle. This sequence happens each time. what do you recommend to get it to work? thank you very much. Lori.


You could check into the User's Guide online manual below:http://safemanuals.com/414159.php?k=41da0c038c6dca28da72cf9056db1c61&ID=63815&q=MIELE%20G2470 ... Miele Dishwashers

Model#SHX4AP05UC/04 on start up can hear pump running water fills for 30 sec then pump runs stops and clean led is on ?


... Bosch Dishwashers

KitchenAid KuDS301XBL6. After cycle has run. I unload dishwasher and shut the door and the machine starts "draining" again. Only way to stop it is to open the door slightly. If I bump it it starts


... Dishwashers

Whirlpool gold, quiet partner III, My dishwasher is not cleaning very well and when it is done it flashes clean. The clean flashing light wont stop. It flashes 7 times and stops for 3 sec then starts again. I know how to reset washer using heated dry and normal buttons but when i run it again when it is finished it goes back to the clean button flashing


... Whirlpool Dishwashers

Hi...my dishwasher 'clean' light continues to blink. I can hit cancel and it sounds like the cancel cycle is running. After that the light keeps blinking and I can not start the machine. If you hit start the light goes on, then stops, and the clean light flashes again. Any clues? Thanks!


Sounds like the control board or panel is shot. What is the model number of the unit, and serial number? ... Dishwashers

I have an avanti dw 18 dishwasher . the problem i am having is the when i turn the on button on the motor goes on however no water fills up. The motor is only humming. But; when i press down the float from inside the machine the water fills up and the machine starts to work. after the water drains again the motor continues to run and hum and the dial does not move. when i manually move the dial nothing seems to change . the motor continues to only hum. Even when the dial is in the stop position


... Avanti Dishwashers

FDW60 Hello, I have a Hotpoint FDW60 dishwasher. It seems to have the usual quality issues but the actual problem is different to most I see on here. The machine has only been used about 20 times, but yesterday the following happened, I loaded and selected intencive program, when I pressed start the machine made a shriek/chipping sound, it seemed to run for about 5 seconds then stopped with the power and prewash lights flashing erraticly for about 3 seconds then was totaly dead, no power light o


Tom,\015\012If your dishwasher is still under warranty, best thing will be to contact Hotpoint's service center for repair the problem. ... Hotpoint 24 in. FDW60 Free-standing Dishwasher

I have a Whirlpool ADF951, it has power to it and was working fine, the power light is on and the green light to the far right of the cycle lights is flashing, I can only get any response if I hold the start button in for about 10-15 seconds, The machine stops the light flashing and makes the noise like it is starting , that goes for about 20 secs then returns to the flashing light stage, any idea's please


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks\015\012for using FixYa. If the light flashes, pauses, and then repeats. When\015\012the dishwasher doesn't sense a water tempera ... Dishwashers

My pressure washer will start up and run for about 10 secs & stop


I have the same problem. Has any one answered this one yet? ... Mi T M WP-2700-4MHB Pressure Washer

Machine starts and pump runs but then stops after a few seconds - it does not seem to be filling


... Bosch 24 in. SHU66C02 / SHU66C06 Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1417 seconds