Having problems with your Craftsman 2500 PSI Briggs & Stratton Powered Pressure Washer ?

Why will water not flow through hose into the spray gun with the washer not started as well I started the power washer and the water still does not come out.

\015 I took the hose tool kit (192914GS) off the unit and misplaced the spring. I got a spring but not sure sure if the size is proper and Craftsman will not provid details and warnts to sell the kit as 1 package. \012Also what is the proper way to put it back together. Going outwards from the engine-->o ring-->ball bearing-->spring\012Is this the proper setup and if someone can provide spring dimensions that would be great.\015

Answers :

Repair Help & Product Troubleshooting for Craftsman 2500 PSI Briggs & Stratton Powered Pressure Washer

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Why will water not flow through hose into the spray gun with the washer not started as well I started the power washer and the water still does not come out.


... Craftsman 2500 PSI Briggs & Stratton Powered Pressure Washer

Very little water flow from washer . Once water is connected to the intake side of washer very little is coming from the out site to power nozzle when engine is started it still does not boost water preasure


... Pressure Washers

Dishes are still dirty. I have used every kind of dishwasher aide, half loaded it and dishes are still dirty, I let the water run until very hot before starting the washer. The washer says you don't have to rinse but I do and they still come out dirty. Also black nasty stuff comes up from my garbage disposer.


Suggest the problem may be a plumbing issue - likely substantially blocked drain system, so the dirty wash water cannot properly pump out but rather remains in the dishwasher.\015\012\015\012Suggest getting a plumber in to "snake" out you ... Dishwashers

Maytag Dishwasher Model MDB4100AWQ When I start the Light Wash Cycle: Washer fills with water, heater comes on (I checked it with a volt meter--120 volts), timer runs, motor never runs, before the timer gets to "rinse" the heating delay light on the door comes on and the timer stops. The heater is still on (120volts) nothing further happens it just boils away on the water in the washer. Note: If I manually forward the timer to "rinse" the motor will kick in and run but does not pump out w


Most common d/w power is 120 volts, check for 120 volts with a  ... Dishwashers

Bosch SHX33A: lights come on properly in response to buttons, it has power. Close door, it makes the normal startup sounds, then water flows in. Normally, at this point washer starts into normal cycle. Instead, it just sits there and nothing happens. Forever. Not a matter of patience: we've left it in that state all night long. Have flipped power circuit and started over, everything else I can think of to kick-start it, no change.


Hi\015\012\015\012The issue seems to be with the motor or the door latch\015\012assembly going bad and should be replaced. The washer won't start the cycle if\015\012motor is not working, as its filling with water so I believe that the do ... Bosch 24 in. SHX33A02 / SHX33A06 Free-standing Dishwasher

My dishwasher will not start. It is a frigidaire / electrolux FDB1050REQ. I have checked thepower....and reset the circuit breaker.......then pushed the start button.....the light comes on on the front of the washer like normal but no water starts filling. I have jiggled the anti water overfill device but still nothing. HELP!!! The front of the dishwasher says Frigidaire, however, the inside of the door where the model# is says Electrolux


... Frigidaire Dishwashers

Hotpoint HDA3400g dishwasher is not running. I have checked to make sure it has power. Took the washer apart, checked that it had power through the door switch to the timer control, all is well. Still not running or getting water into the dishwasher. Any ideas besides replacing the water inlet valve? Will this dishwasher cycle through if it does not have water?


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks for using FixYa. Please check for the following if your dishwasher\015\012is not working-- ... Hotpoint 24 in. HDA3400G Built-in Dishwasher

Power washer starts, water to washer on but no water pressure come out the hose


This with the engine running? If so there eigther is a restriction in the main water feed or the pump is damaged or possibly needs to be rebuilt. Did you know you can never start the mechine with the water hooked up and on full and you should trigger ... Briggs & Stratton Power Products 1539 Pressure Washer

I own a KUDS01FLSS3 KitchenAid dishwasher. The lights on the control panel do not come on and a cycle can not be started. There is about an inch of water in the bottom of the dishwasher basin and it looks like the previous cycle did not complete. I have checked the wall outlet that the washer is plugged into and the washer is receiving power from the wall. And ideas? My next thought was to take the door off and check the power supply running to the door panel and control panel.


Servtek06 writes:\015\012check connections @ control board/module. May be Control Board/Module. ... KitchenAid 24 in. KUDI01FLSS Stainless Steel Built-in Dishwasher

Power washer My generac 6670gp power washer surges frequently. Especially when I try to increase the volume. I let the water run through it for a couple of minutes prior to starting it. It actually seems to pulse just coming out of the hose without the moter running. Am I doing something wrong?


... General Pressure Washers

My Kenmore Diswasher (Mod # 665.17842400) has crapped out again. Towards the end of a cycle, the power seems to have been lost. There is now water in the bottom, and the user interface won't come on. 2 months ago I replaced the user interface and the magical board it connects to to solve a start button problem. I checked the power coming to the washer and it is live.


There is a thermal fuse on the control board. It protects in a overheating problem or sometimes when there are to many appliances on the same circuit that creates a high amp draw, that melts the fuse not actually blowing it like a short. Check your d ... Kenmore Dishwashers

I have a Husky 2600 PSI power washer with the Honda GCV160 engine that I can't get to start. It was okay when I purchased it from Home Depot last spring but now I've tried putting new gas in it, spraying carb cleaner, new spark plug, and it still won't start. I only ran it for about 30 minutes when I first purchased it. The guy at the service desk at Home Depot told me that the water hose should be attached and turned on while trying to start. Is this true or would this be starting the motor und


You can eliminate the motor by unbolting the pump from it and then if it will start the problem is with the pump or the unloading valve.If it does not start with the pump removed then you check for spark and get the carb cleaned or have a kit put in ... Karcher 2500 PSI Pressure Washer

My Kenmore Elite dishwasher doesn't wash dishes properly. I think that it is not getting enough water in the machine. It only allows about an inch of water to get into machine and then starts. I do not think that there is enough water to spin wash arms. I have 40 PSI coming into the house. I am on well water and found debris in the intake orfice. I did my best to flush. Could it still be bad?


I am having the same problem with my brand new Dishwasher. ... Kenmore Dishwashers

My bottom dish washer was draining the water on the top dishwasher and there is always water left over on the top.I remove the pipes and put CLR to clean up drain.Start both dishwasher on rinse cycle ( 12 min cycle) then at 10 min.they start blinking with a No tap (may be water ) sign on it. I run the cycle again now a F1 sign coming with a tool sign.And both dishwasher going crazy ,it turn on by itself even I powered them off.


Hi\015\012\015\012\015\012Thanks for using FixYa. F1\015\012error means that the flood switch has been activated. You'll need to reset it by poweri ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

Using a Bosch 1600W Pressure washer Aquatak 110 plus Was adjusting the twist pressure sleeve to get HIGH pressure and water supply stopped and sleeve seems fixed/seized. I turned power ON and OFF and turned water tap ON and OFF but still no water coming out of the nozzle. What do I do now?


... Pressure Washers

Water wont come out of gun of power washer before starting it


... Briggs & Stratton Vox Professional 2500 PSI (Gas/Cold Water) Pressure Washer w/ Honda GX

I started working with the Karcher KB4040 pressure washer and all was well for 1-2mins, then it sputered a bit and all power died. All hoses were still attached properly, it hadn't blown a fuse in my house and the fuse in the plug of the washer is working fine.When I switch it on I get nothing. Do you think the motor has packed in? I borrowed the machine from my neighbour who's away on holiday, so don't know much about age of the machine. Any advice much appreciated.


If the water is in anyway impeded, like kink in hose the unit turns off and goes into protection mode. That it it shuts down for a pewriod of time depending on how hot it may have got.\015\012When its rested try it again ensuring you definitely ... Karcher 1750 psi Electric Pressure Washer

Pump Issue I have a john deere pressure washer. I hook the hose up to it, rurn the water on and no water comes out of the wand. I started the engine briefly and pulled the trigger on the wand and still nothing. The model number of the pump is Annovi Reverberi SJV 2.5G24-1. I can't seem to find any info on the G24? There is info on the G27-1. Not sure what to do here? Please help.


... Pressure Washers

Husky 500 2200 psi. starts and runs ok, but no pressure through the wand. hooked up garden hose to power washer turned water on and it comes through the hose ok, but start up and put wand on and no pressure.


... Pressure Washers

Hello, We have a Candy Diswater that is just arround 2 years old. When it starts it takes water and then you hear the washer going into loop. It tries to do something els but doesn't seem so. If you open the door you can see water inside but no progress or heating. If you also try to change the program it doesn't change as well. Before it got to this point sometimes we used to unplug the power and tunr it off and then ON and then it works. However, now this procedure is not working an


Quite possibly could be the timer and could also be the main control board as well. Sometimes unpluging it will help for short times but if a serious problem persists it will only be a temp fix... ... Dishwashers

I bought a honda pressure washer power boss 3000. I load the gasoline, start the machine, but pressure water is not coming out from the trigger. i tried so many things , but can t get started.


If you are using a water tank for water supply, remove the water supply line from the pressure washer and connect a water hose from a faucet. Turn the water on, then crank the engine. Pull the trigger of the spray gun until water comes out. When then ... Honda Pressure Washer PSI 3000

Power washer starts no problem but when turned on and activating the trigger on the pressure washer gun, water no longer comes out. The gun itself was replaced not long ago. What could be the cause?


The tip could be plugged up ... Honda Pressure Washers

My Delonghi Dishwasher keeps turning off. The dishwasher is turned on at the power point. The water is turned on. Okay When I press the POWER botton on the front it wont stay on. I have to keep my finger on the POWER button and then press the START button for washer to work. If I do this it will then pump out any water in the bottom and start to work. ***BUT when you take your finger of the POWER button the washer just turns off and stops working. Do you have any idea what could be the problem p


Yes, the power button is faulty. by pressing the power button forcefully, you are in effect allowing the contacts to close. Replace it. ... Dishwashers

Dishwasher does not start it seems there's no water coming in the tub. I got a trouble shooting manual from ejunkie.com and tested the coil of the water valve which read 1000 Ohms, which means it's OK. Then I hot wired the coil while connected to the water line and the valve opened and I had water flowing [ in a bucket] I have tried to start the test program [hold power scrub plus and regular switch at same time then start button] and lights start flashing you hear drain pump come in then the un


... Bosch SHV4803 Dishwasher

I have a washer model 1805 (1800 PSI). Everything works but there is always leaking of water (sprays) when I use it. The leak is not from where the water hose connects to the washer, but where the black piece attached to the hose is connected to the body of the washer. I can still do a decent job of power washing, but am wondering if the leaking of water is reducing the power of the washer.


Yes, leaking water will reduce the pressure. Sounds like you need to replace the O-Ring inside the connections on the pump. This is where the pressure hose connects to the pump. If you look carefully inside that connection you will see an O-Ring. Use ... Campbell Hausfeld PW1805 1800 PSI 15 GPM Pressure Washer
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.2019 seconds