Having problems with your Craftsman 2700 Max Psi Pressure Washer 23 Max Gpm ?

Used 5 times, stopped running while using it, now won't start. Pull rope pulls easy. Suggestions ?


Answers :

Repair Help & Product Troubleshooting for Craftsman 2700 Max Psi Pressure Washer 23 Max Gpm

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Used 5 times, stopped running while using it, now won't start. Pull rope pulls easy. Suggestions ?


... Craftsman 2700 Max Psi Pressure Washer 23 Max Gpm

I have a Briggs & Stratton gas power washer. This is the 1st time this year that I have used it. I put in fresh gas, hooked up the water supply. The engine started and then quickly stopped. I had to release the water pressure in the hose before I could pull start the engine. The only way to keep the engine running is to hold down the spray nozzle trigger. Once that is released the pressure in the hose builds up and the engine stops.


Sounds like the unloader is not working correctly. Try replacing it and see what happens. ... Briggs & Stratton Prosumer 20324 Gas Pressure Washer

Engine will not turn-over. It is a Honda 11 HP, OHV on a Karcher Pressure Washer. It was running fine for about 45 minutes. All of a sudden it stopped. When I tried to start it again, the engine is bound up so that the pull rope will not pull out at all. It has plenty of gas. The crank case is full of oil, not over full.


Pull the spart plug out and see if you can pull it. Sometimes the carb will flood the engine to a point that they get hydrolic lock.If it does free up then I suggest cleaning the carburator before trying to start it again.If it does not free up the y ... Karcher 2500 PSI Pressure Washer

Whirlpool gold, quiet partner III, My dishwasher is not cleaning very well and when it is done it flashes clean. The clean flashing light wont stop. It flashes 7 times and stops for 3 sec then starts again. I know how to reset washer using heated dry and normal buttons but when i run it again when it is finished it goes back to the clean button flashing


... Whirlpool Dishwashers

My Frigidaire dishwasher keeps showing the Er uo codo on the display. It used to would finish a load even though it would stop for a while when the error message came up, but now it will not run at all when the error message comes up. I read on this site that the Er uo has to do with the vent. I pulled the dishwasher out and removed the vent. I turned the dishwasher on and the vent opened and closed about three times when the cycle started, then it stopped and the error message came up. Is


Hi. This code is in reference to the vent assembly. This may also be a control fault, as well. To isolate the culprit, you will need to make sure that the vent assembly is not blocked. If it is blocked, it must be replaced. Restricted air flow will c ... Dishwashers

I have been negligent in not cleaning out the filters and after the unit more or less stopped, I pulled the two filters finding them full of what looked like soap scum. I cleaned them best I could (but noticed the inner filter still had most of the small holes blocked) Started the unit and it cleaned alright for a couple of days. Last night after running a load all the water did not empty from the bottom of the tub? Any suggestion on what wrong? Bought the unit on 1/19/05. Thanks


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks\015\012for using FixYa. Dishwasher not draining properly or not draining at all issues\015\012can arise due to different reasons ... Bosch 24 in. SHX46A02 / SHX46A06 Built-in Dishwasher

The last time I ran my MDB5100AWB, Quiet Pack, Maytag Jetclean Dishwasher, I stopped it shortly after starting it then went to bed. It hasn't run since. Nothing happens when I press any of the buttons; no lights, no motor, no reaction whatsoever. Is there a reset button? Any other suggestions would be most welcome. Thanks.


... Maytag MDB5100A Dishwasher

Honda GX 240 on woodsplitter stopped running. Tries to fire a couple of times each pull but dies. Found debris in gas tank. Cleaned out the tank and hose to carb. Cleaned out the sediment cup. Cleaned out the rust and debris from the bottom of the float bowl. sounds like debris in carb jets? Is it worthwhile taking the carb apart and cleaning it, or just order a new carb?


Install a new plug, and make sure your gas mixture is not to rich, And you air cleaner is clean ... Honda 8 HP Engine

I have a Ryobi power washer, model #RY30080. I ran it for a long time yesterday, running it out of fuel. This morning, after refilling the gas, I am unable to start it. The starter rope is very difficult to pull, like it is binding. I followed the correct starting procedure. Can you help me?


It is more likely the pump seized up... or you are experiencing combustion lock.\015\012Remove the sparkplug(s) and pull the cable a few times.\015\012If the motor turns normally - clean the plug or replace it.\015\012If the motor s ... Pressure Washers

I have a Bosch (SHU5302UC/U12). The washer often takes 2 or more hours to run. Sometimes it gets stuck for a long time part way through (e.g. just sits at "43"). Other times, it gets stuck at 1 and won't stop on its own. The latest thing is 2 dots have appeared on the display that I've never seen before. For example, instead of "43", it reads "4.3." Eventually it gets to "C.L." but does not stop running. Also, its been making very strange noises during part of the wash cycle.


... Bosch 24 in. SHU43 Built-in Dishwasher

8 years ago we bought a model 665 Kenmore Limited edition Stock #575-0 if you need that. A certified kenmore tech. has been out here 3 times with still no clear answer. The problem is when you run a standard cycle of 95 minutes it counts down to 78 minutes and stays at that time for about 45 minutes then stars counting down again till 42 minutes then stops at that time for about another 45 minutes then coutinues till it finishes the wash and drying cycle. It runs and sounds fine the entire time


Sounds like timer prob.would rec. replacing timer ... Dishwashers

This problem is intermitten. Kenmore 665 16765690. starting the dishwasher, I hear a motor running. I think it is trying to empty water, however there isn't any water. I will turn the time rotor around to the start again. Sometimes, when I do this the motor running sound has stopped and I hear gurgling sound of water entering. Once this happens, the cycle is good and does well. However, there are times, rotation the timer back to the beginning may take several times, up to about 20 times.


Hiclean water filterthe presure is to lowPls vote me to keep us alive ... Kenmore Dishwashers

Good mroning after starting any program first the pump will run followed by water intake. After a while the machine stops and the light intake/drain starts blinking. Most of the time water will stay in the machine. After pressing the on/off bottom first switching the machine on again and starting a new program the machine pump start running emptying the water but than stops after a short water intake again. I opened the water stop but it seems to be ok. The filter inside the machine is cle


Good morning don't get shocked because ullu ki to abhi subah hi hui he ... Miele 24 in. G892SCU Plus Built-in Dishwasher

Hi I have a mdb6601awb maytag dishwasher. Sometimes when it starts the wash cycle it will make a loud squelling noise. Then if you pull on the handle and stop it, the machine will start and sometimes the noise will be gone. Or you may have to do this 3 or 4 times before it will stop making the squelling noise. I do notice when I pull up on the handle to stop the machine it makes some clicking noises and then the noise goes away. Thank You for any help you may be able to give me!!!


I don't have a solution however I have the same problem with that same model. ... Maytag 24 in. MDB6601AWS Stainless Steel Dishwasher

I have the Whirlpool DU 1100 dishwasher and the clean light kept blinking. I did the heated dry, normal combination and got it to run through the diagnostic check and sure enough it cleared the lights and appeared ready to run. When I would start it up again it would run the water and then get to the soad wash cycle and stop. No more lights it just stopped. I have been through the diagnostic process 3 times and still same problem. HELP


... Whirlpool Dishwashers

Over the past two years, the machine has occasionally stopped in mid cycle, while the pump continues to run, but the cycle stops advancing. Each time there has been water in the plastic pan under the pump, valves, and other mechanisms. The float switch has been tripped, stopping the cycle. Occasionally. but not always, the pump inlet has been partially obstructed by food waste. After bailing out the pan, the machine will run normally for weeks or months. There is no indication of a leak into th


Please post the exact make & model # so we can be more exact.\015\012THanks!! ... Dishwashers

Hello, I have a CONSTRUCTA S9W1C dishwasher with aquastop. Unfortunately, I tried once to start it with the house water supply closed. Of course it stopped after a few seconds. After that time, when I start it, the water pumps works and after some seconds the cycle stops. It gets no water. I've checked and noticed that no water passes through the aquastop valve. The aqua stop has two wires that get into the dishwasher. Do you have any suggestions? Thank you for your time Alex


... Dishwashers

I have a Honda 5.5 hp pressure washer and it wont keep running I bought it off craigs list they said the last time it ran was almost a year ago I took off the carb and sprayed carb cleaner threwout but didn make a difference I cant seem to see any jets juist the float needle and that was clean if I pour gas in the carb it will run for a for about 5 seconds and but wont stay even if I choike it. does anyone have a answer


Try soaking the carb for 15 minutes in gasoline. If you have a plugged port just sparying may not be enough to clean it ... Honda 2500 PSI Gas Pressure Washer

We have a kitchenaid dishwasher, kudi22ot3, installed in 1992. It is not cleaning dishes even thought the tub is getting water, and we've run dishwasher magic through it a couple of times. The dishes will get clean for a few runs, and then will stop getting clean. Is it time for a new dishwasher or can this one be fixed? Thank you.


Hi,There are 6 major reasons that could affect the cleaning.A nice guide you could follow is :-http://www.partselect.com/dishwasher+dishes-not-clean+repair.htmOther than this, you need to check the pump. Make sure ... KitchenAid Dishwashers

Dishwasher Dilema Hi, Can someone help me solve this problem. Last time I had a problem with my dishwashers I was pretty successful in solving it on this site. I was running a reg wash on the top drawer of my Fisher&Paykel when I suddendly had to stop it in the middle of a wash to add more dishes (something I do all the time) suddenly both screens started beeping with an F1 along with a wrench. It sounds like both motors top and bottom are running full blast. I tried shutting the power for a few


You need to remove the bottom drawer and dry out the water with towels and a hair dryer when this is done it should operate normally. most likely when you pulled out the drawer the water sloshed back and out of the drawer making the dishdrawer think ... Fisher and Paykel 24 in. DD603H W Built-in Dishwasher

Dishwasher is less than a year old. Once in a while it will stop about 10 minutes into the cycle, then the display lights will blink. Sometimes it will stop and the lights wont blink so we will come back later thinking it is done only to open it up and there is water sitting in the bottom. Doesnt happen all the time but sometimes and yesterday happened about 10 times finally gave up. I can cancel and restart the cycle but the same thing happens.


I would most likely guess a faulty latch....it will cancel the cycle, thinking that the door has opened, and the lights will flash. After a certain amount of time, it might "time out" and reset and the lights would stop flashing. Unfortunately it's ... Frigidaire 24 in. PLD2850 Built-in Dishwasher

The cycle doesn't seem to stop correctly. I start a load. It doesn't seem to matter which mode that I start in, but it will count-down the time, but at the end it hasn't stopped running. I've cleaned out the filter and the trap below. I've ran vinegar through a cycle. I've cleaned all of the spray arms. It doesn't seem to advance out of the wash mode. There is still some suds at the end. I have to end the cycle by canceling and draining it manually, then run a couple of "rinse--9 minute" cycles


Hello,\015\012\015\012Based on your description I'd say the issue is with the control. That is what I'd be looking for if called out to service the unit with the symptoms you've described. \015\012\015\012The issue is within t ... Bosch 24 in. SHU43 Built-in Dishwasher

When I press the on button the cycle light is on at the 50 degree setting and I cant change the setting and it wont run on that cycle. It has happened several times but this time it wont come around


Looks like micro controller problem. Contact authorized service center. ... Dishwashers

Lights blinking The light on my ASKO 3112 dishwasher wont stop blinking and it wont stop running, how do i fix it?


I have a 3122 and had a similar problem, Lights flashing, humming noise and me standing there scratching my head! I emptied all the water out of the filter basket and then tilted the machine backwards (only needed about 20 degrees) and then the rest ... Asko 24 in. D3112 Free-Standing Dishwasher

After the wash & dry is complete, the next time I try to use it, won't turn on. I tried cancel and that starts and finishes but can't get any thing else to work. I turned off the circuit breaker but have to wait 6-8 hours before turning back on. Once this is done the machines runs normal again. I have to repeat this process every time I want run. Any suggestions on what might be causing this???


I have the same problem. The only temporary solution I have so far is \015\012to turn off the circuit breaker and wait between 10 & 30 minutes \015\012before resetting the breaker. The the dishwasher will work for one \015\012cycle. ... Whirlpool 24 in. GU1500XTLS Stainless Steel Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1604 seconds