Having problems with your Craftsman 2700 PSI Briggs Stratton Powered Pressure Washer ?

How do you start the engine - Craftsman 2700 PSI Briggs Stratton Powered Pressure Washer


Answers :

Well without knowing your specific engine I will give you the general steps.\015\012make sure there is fresh fuel in it (everyone has forgotten this sometime)\015\012there is possibly an ON/OFF switch on it somewhere. turn that on \015\012then there may be a priming bulb, a sort of rubber round thing that you will push several times. this should be on top somewhere. \015\012then put the throttle control to "full" or "start" or perhaps a picture of a rabbit.\015\012Then pull the cord. if it does not start right away try a few more times. if it still does not let it sit for a while then try again.
Repair Help & Product Troubleshooting for Craftsman 2700 PSI Briggs Stratton Powered Pressure Washer

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Cannot start engine after rebuild - Craftsman 2500 PSI Briggs & Stratton Powered Pressure Washer


... Craftsman 2500 PSI Briggs & Stratton Powered Pressure Washer

How do you start the engine - Craftsman 2700 PSI Briggs Stratton Powered Pressure Washer


Well without knowing your specific engine I will give you the general steps.\015\012make sure there is fresh fuel in it (everyone has forgotten this sometime)\015\012there is possibly an ON/OFF switch on it somewhere. turn that on \015\012then there ... Craftsman 2700 PSI Briggs Stratton Powered Pressure Washer

I have a Briggs & Stratton gas power washer. This is the 1st time this year that I have used it. I put in fresh gas, hooked up the water supply. The engine started and then quickly stopped. I had to release the water pressure in the hose before I could pull start the engine. The only way to keep the engine running is to hold down the spray nozzle trigger. Once that is released the pressure in the hose builds up and the engine stops.


Sounds like the unloader is not working correctly. Try replacing it and see what happens. ... Briggs & Stratton Prosumer 20324 Gas Pressure Washer

Engine lockup I have a craftsman power washer with a briggs and stratton 850 series engine, craftsman model 580752220, the engine will not turnover unless i remove the spark plug, it has electric start and will turn over with no problem like this but if i put my finger over the plug hole it locks up immediatly


Sounds like the intake or exhaust valve is not opening. ... Craftsman 2700 PSI Briggs Stratton Powered Pressure Washer

Started by Craftsman 2700 PSI , 2.3 GPM Briggs & Stratton Powered Pressure Washer for first time in 9 months. Added new oil, and gas. started but is smoking from muffler and is dripping what appears to be oil near the exhaust end. I shut it down. What could this be due to?


The first thing I would check would be the oil level, to make sure you didn't put in too much oil. If the oil level is correct, it could be a stuck piston ring, letting oil blow by the piston, and out the exhaust. If this is the case, you are going ... Craftsman 2700 PSI,2.3 GPM Briggs & Stratton Powered Pressure Washer - Ca. Model

Have a Craftsman 2550 MAX PSI, 2.3 MAX GPM, Briggs & Stratton Powered Pressure Washer seems like the engine is ceased how can I fix it? need a copy of the manual with exploded pic of engine


... Craftsman 2500 PSI Briggs Stratton Powered Pressure Washer

Two problems please: craftsman 2150psi briggs and stratton engine washer, will not start when hot. and secondly, i was washing with regular pressure, then noticed a pressure drop at the nozzle, then the unit shut down. no water leaks at the manifold. water supply was strong. any ideas?


Nozzle dirty, clean out with small diameter wire. ... Pressure Washers

Won't start - Craftsman 2700 PSI,2.3 GPM Briggs & Stratton Powered Pressure Washer - Ca. Model


... Craftsman 2700 PSI,2.3 GPM Briggs & Stratton Powered Pressure Washer - Ca. Model

How to drain oil from engine - Craftsman 3000 PSI 27 GPM Briggs Stratton Powered Pressure Washer


Square socket on the bottom of the engine. I think a 3/8 extension on a ratchet is correct. ... Craftsman 3000 PSI 27 GPM Briggs Stratton Powered Pressure Washer

I have a Craftsman 2700 psi pressure washer with a Briggs and Stratton 850 engine (80 year anniversary special addition) . It is about 2 years old and used very little and will not start. I filled it with fresh fuel and checked the oil. I also replaced the spark plug and air filter. I checked the fuel line thinking it may not be getting fuel, but there is no obstruction from the tank to the end of the fuel line. I am out of TS options short of taking it to a service center.


Here is the long answer with everything we learned while using a power \015\012washer twice a day for years::\015\012It sounds like could be one of the problems listed below or a \015\012combination of those things.\015\012\015\0121 ... Briggs Stratton 020273 Elite Series Portable Gas Pressure Washer

I have a 2500 craftsman power washer with a Briggs and Stratton engine. I used it about a month ago and it worked fine. Took it out yesterday and I could not pull the rope to get it started. I took out the spark plug to release the compression but I still could not pull the rope out it is locked any advice.


It sounds like the pump is seized. Make sure any pressure has been released by pulling the trigger on the gun. Sometimes this will allow you pull the cord. If the pump is seized, a new pump would be in order. ... Briggs & Stratton Pressure Washers

Craftsman power washer stalls under load - Craftsman 2500 PSI Briggs & Stratton Powered Pressure Washer


... Craftsman 2500 PSI Briggs & Stratton Powered Pressure Washer

Craftsman pressure washer model 580.752520 - Craftsman 2500 PSI Briggs & Stratton Powered Pressure Washer


... Craftsman 2500 PSI Briggs & Stratton Powered Pressure Washer

Hard starting 6hp Briggs and Stratton power washer engine. I poured a teaspoon of gas into the cylinder; reinserted the spark plug and with one pull in ran fine. This is a choke start engine and it may take 12 to 15 pulls to start on a cold engine. The unit is clean. The air cleaner is new. The spark plug is new. The unit is 2 years old with very little use.


Hello. I have this same machine. Go to the auto parts store and get an aerosol can of starter fluid. Have a helper squirt some into the air intake while you start it. Then continue to squirt a little starter fluid as it runs for the first two mi ... Campbell Hausfeld Pressure Washers

Power washer won't start - Briggs & Stratton Power Products 1539 Pressure Washer


Have you checked for spark? You can remove the plug, touch it against the block and crank it and see if you have any spark (best done in as dark a place as possible). If you don't have spark, start by replacing the plug.\015\012\015\012 ... Briggs & Stratton Power Products 1539 Pressure Washer

Honda 2500 pressure washer manual - Craftsman 2500 PSI Briggs & Stratton Powered Pressure Washer


... Craftsman 2500 PSI Briggs & Stratton Powered Pressure Washer

I have a craftsman w/ honda model # 580752060 pressure washer. Started washing & after about 10 min. lost all pressure, no water comes from nozzle while engine runs. Cut off engine & nozzle sprays


You have a clog somewhere ... Craftsman 2600 PSI Honda Powered Pressure Washer

Gas in oil in pressure washer - Craftsman 2700 PSI Briggs Stratton Powered Pressure Washer


... Craftsman 2700 PSI Briggs Stratton Powered Pressure Washer

Home Depot has a lawn mower with the Honda GCV160 Electric start version engine. They also have a pressure washer with the Honda GCV160 engine. I have a disability that makes it difficult to pull the starter rope. I would like to get the electric start on the pressure washer. My local Honda bike shop service center said they use different blocks. Can I get a pressure washer pump mounted to the Honda GCV160 Electric start version engine? If necessary, are there adapter plates that can be purchase


... Karcher 2500 PSI Pressure Washer

Power washer Craftsman B&S engine model 20228 - carb not working


... Craftsman Pressure Washers

I have a Briggs Stratton Model# 020228 Gasoline Pressure washer with a Faip Brand Pump. The engine starts, the water supply goes thru the pump under its' own pressure. When I pull the trigger on the handle, there is not increase of force nor does the pump engage. I had this same problem several years ago and sent it to a dealer for service. His service tag indicated a stuck unloader. Where is the unloader located on this pump. The indentification on the pump is MTPV90736 191693 Order # 52


... Briggs & Stratton Pressure Washers

Campbell Hausfield Pressure washer model 1549. After a few years of storage, I cannot prevent the powerful spray leaking from the connection between the Gun and the Lance. I replaced the O-Ring, and tried other means unsuccessfully. Spray from the joint is almost as powerful as spray from the lance nozzle. The Briggs and Stratton engine has been cleaned and operates well. The pump operates well. But the lance connection refuses to seal.


Hello,Most likely, the housing has split and seal is not being made. There is a chance that the hose is leaking where the fitting is crimped on (my experience, but different pressure washer). Are you able to see a leak when turned off b ... Campbell Hausfeld Pressure Washers

I have a older simpson 3000 power washer, 11 hp honda,been a great machine, owned since new, seems like the pressure is building up to a point where it has blown 2 hoses, i turned the throttle down and started to wash, engine quit after about 15 min. it restarted and quit again, tried starting fluid , nothing, what might be the issue


... Honda Pressure Washer PSI 3000

My Husky pressure washer 2600 psi powered by a gcv 160 Honda. Engine starts no pressure other then from water source and soap is not being dispensed


It sounds like the (RMW 2.2 G24) pump has gone out. Mine had this problem after about 6 hours of use. I was able to order a new pump for around $160.00, and then installed it myself. Go figure it was just out of warranty. I think my next pressure was ... Pressure Washers

I have a Craftsman power washer model 580 752020. When I start it up, turn on the switch the electric motor runs fine until I either close the trigger to the spray nozzle or press the trigger for power spray. The electric motor just shuts down, if I take my finger off the pressure and let the water run with no presssure the motor runs fine. My question is this. Is the capasitator on the electric motor the probable cause and is there a way to check out the capasitator to see if it is malfuncti


I doubt that it has anything to do with the capacitor on the motor. i think you are having a problem with the actual Motor Drive circuitry. What is happening is when you close the switch, this tells the Motor to "Ramp Up" to pump the water out, what ... Craftsman Pressure Washers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1559 seconds