Having problems with your Craftsman 2700 PSI Briggs Stratton Powered Pressure Washer ?

How is the pump separated from the shaft of the engine to do a pump replacement?


Answers :

Repair Help & Product Troubleshooting for Craftsman 2700 PSI Briggs Stratton Powered Pressure Washer

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

How is the pump separated from the shaft of the engine to do a pump replacement?


... Craftsman 2700 PSI Briggs Stratton Powered Pressure Washer

My pump is gone on my pressure washer. The honda engine is GC 160. The pump is a model VRX2527G. How do I pull the pump off the engine to replace it. I removed the four bolts from the pump housing, but the pump is still tight to the shaft. Please explain the removal process.


Hello,Your pump sits on a keyed shaft, versus a taper fit. This is good, since tapered shafts will require a puller to remove the pump.Since the pump is already bad, you have a few options available to you. 1) W ... Honda Pressure Washers

I had a bolt break off the engine shaft end and tookthe pump apart and replaced the bolt. How do you fill the pump back up with oil?


The pump housing usually has a plastic viewport about half way up on side of pumpOil should come to middle of viewportUse 20 or 30 weigh ... Karcher 2500 PSI Pressure Washer

Troy-Bilt 2550 20293 pressure washer not producing pressure. Worked when last used 2 months ago. Pump pistons are moving up and down when engine is pulled through. Inlet water is flowing through pump but no pressure when engine is started. I have the same problem. Water flows thru the pump when not running, but no flow or goes in by-pass mode when I start the pump. The pump being Troy Bilt Model 020296-01. I replaced unloader valve even. Anything else I can do?


You replaced the unloaded valve. Are you positive you have the unloader screwed to pressure and not turned the opposite way? You will have no pressure if it is adjusted wrong. One other thing I have encountered is that the unloader has a ball bearing ... Pressure Washers

Have a leaky gate valve shaft seal that I want to replace myself (part # WD8X181). It only leaks when in the drain cycle. Repair manuals are not available for this model. How much disassembly is involved to replace this seal? Do I need to gain access to the shaft from inside the housing pump assembly (drain sump)?


... GE Dishwashers

I have a leaky gate valve shaft seal that I want to replace myself (part # WD8X181). It only leaks when in the drain cycle. Repair manuals are not available for this model. How much disassembly is involved to replace this seal? Do I need to gain access to the shaft from inside the housing pump assembly (drain sump)?


... GE Dishwashers

North star eletric hot 2000 psi 3.5 gal per min oil pump had blown shaft seal. replaced with new pump. put small allen plug in return port. I have oil flow to the pump but none comes out port leading to burner even with shutoff switch removed and pump turning. Installed test gage 0 pressure. Took off bypass line and ran into can. pumps small amount of fuel into can that way but with uneven flow & small bubbles. nomatter what I do I just can't get fuel outlet port to burner. pump # A2VA-7116 pl


... Northstar Pressure Washers

Replaceing a water pump in a 2003 frieghtliner with a 3126 cat. have water pump loose from engine but will not come completely off. Does the oil cooler or the front accessory bracket need to be removed to get pump off?


... Caterpillar CAT Pump Pressure Washer Pump Oil

Leaking cap screw on pressure washer pump - General Pump EZ4040G Pump 3400rpm Direct Mounted to Gas Engine Shaft with 4 Bolts


... General Pump EZ4040G Pump 3400rpm Direct Mounted to Gas Engine Shaft with 4 Bolts

Won't start I have checked the spark plug and I have good saprk. I have checked the fuel sysstem and the primer bulb injects fuel. I have removed the head and cjecked for engine damage and all cycle correctly. Vaves opne on time piston shows no dmagae. side walls are smooth and not damaged. This engine was working fine but the pressure washer needed some O rings replaced. I have tried to start it with and without the pump attahced. Evrything on the engine looks fine. I removed the spark plug and


... Briggs & Stratton Briggs Stratton 2550 Psigaspressure Washer

FDW60 dishwasher - taken apart pump and that is clear. Seems that dishwasher fills, and empties and heats all OK but water wont go around the machine ie the motor pump doesnt start - any idea how to take this out and replace without having engineer around? Taken small pump apart and its clear. First of all the Eco and fast light flashed, then we took it apart with some direction from online discussion advice. Now Eco and Pre wash lights are flashing. Machine empties water, then fills with


... Hotpoint 24 in. FDW60 Free-standing Dishwasher

I have a pressure washer with a Honda gcv190 engine. The motor runs great but there isn't any water pressure. I removed the manifold and pump and found some mineral deposits and cleaned everything out and while attempting to reinstall the pump on the crankshaft I noticed the key was missing. Upon further inspection it appears that the key was missing from the beginning or had sheared off and then disintegrated. (There were a lot of metal shavings in the pump shaft recess). My main question is th


... Pressure Washers

Remove pump from rusted small engine shaft


... Pressure Washers

Maytag dishwasher model # DWU7402AAB leaking around pump motor shaft. How do I replace the motor shaft seal> do I have to remove the motor to accomplish this?


Hi,Here is the part and they will have instructions with the part.....http://www.partselect.com/PartDetail ... Maytag Dishwasher

How do i replace pump oil? - FAIP Horizontal Shaft Pump A20102


... FAIP Horizontal Shaft Pump A20102

We want to replace the pump to our DEWALT DP3750 pressure washer and can not ge tthe pump to come off the engine. how do you get it to come off?


... Briggs & Stratton Pressure Washer Projectpro Spray Nozzle

Assembly I recently purchased a pressure washer from Home Depot. It is rated at 3100 psi. It is a comet pump with a honda gas engine. The assembly instructions recommended that I remove the plug on the top of the pump and replace it with a vented plug that was provided. However, none of the other enclosed manuls talk about the vented plug. Am I reading the assembly insturctions correctly. Should there be a vented plug ?


HI your machine would have been delivered with a blanking plug in the pump. You will need to remove this and fit a vented pump or your pump will build up too much pressure inside. ... Comet BXD2527 Pressure Washer Pump

Pump disassembly Can't remove drain impeller from shaft. Need to replace motor shaft seal on Maytag dishwasher mod. DWC7302AAB


I removed the impeller on my DW761UQB. The instructions were molded into the plastic pump housing. This is how I DID MINE: Remove motor mount screws. Remove the chopper screw (screw only goes into impeller, not motor shaft). Remove chopper and rotate ... Dishwashers

So I found this power washer for sale. The seller claims that the washer generates a good stream of water, not just full power. He also mentions that after a few minutes the engine starts to bog down like it is working extra hard. Does this sound like a pump issue? Could something be clogged or would the pump need to be replaced? Or should I avoid this power washer?


Don't buy a power that doesn't work.There are many expensive parts on a power washer. If it was cheap and simple to fix, the seller would fix it and the washer would not be for sale.Would you buy a car that doesn't work? Especially ... Pressure Washers

Need manual, how to remove pump from engine, vert shaft 6.o hp


... Pressure Washers

I have a Bosch SGS46E22GB Exxcel dishwasher. It is failing to drain or pump out dirty water. About a year ago we had this fault and the engineer replaced the impeller jug. He showed my wife how to clear a blockage with the left hand side panel removed. I can't get the panle off so am looking for instructions on how to remove it. Thanks


... Dishwashers

My Asko 1502 Dishwasher has water drops coming out from the motor shaft where it is going in to pump assembly.Is there a seal I can buy and replace it to solve the problem? what is the remedy?


... Dishwashers

Oil leak appears to be from pump, not engine, GC160. What oil and how much should be replaced. what might be source of leak


Some pumps have a side glass and oil should be half of side glass and depends on manufacture oil is different if general pump you can use 30w non detergent ... Honda Pressure Washer PSI 3000

I was given a low hour, 10 year old, CH PW205002LE 6.5 HP gas vertical shaft 2000 PSI/2.5 GPM pressure washer with a Lavor pump. It did not work - no pressure. I found a broken o-ring on the brass unloader valve and replaced it with a ring as close in size as I could find as the part break down doesn't state size. Everything was very clean. I coated everything with silicine grease and reassembled, seating the brass piston? as deep as it would go. I had to press the trigger in order to get the mo


My personal experience is that 40% of all the sellers I dealt with on e*** exaggerated their products or worse. If you decide to go the e*** way be sure you put it on a good credit card so you can get your money back if it's a bust. Don't use your ba ... Campbell Hausfeld Pressure Washers

Campbell Hausfield Pressure washer model 1549. After a few years of storage, I cannot prevent the powerful spray leaking from the connection between the Gun and the Lance. I replaced the O-Ring, and tried other means unsuccessfully. Spray from the joint is almost as powerful as spray from the lance nozzle. The Briggs and Stratton engine has been cleaned and operates well. The pump operates well. But the lance connection refuses to seal.


Hello,Most likely, the housing has split and seal is not being made. There is a chance that the hose is leaking where the fitting is crimped on (my experience, but different pressure washer). Are you able to see a leak when turned off b ... Campbell Hausfeld Pressure Washers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0896 seconds