Having problems with your Creda Dishwashers ?

Error Code dishwasher is 14 years old, model number 47918 - error code has appeared in the LED panel inside the door but only shows the letter F, any ideas what the problem may be?


Answers :

Repair Help & Product Troubleshooting for Creda Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Error Code dishwasher is 14 years old, model number 47918 - error code has appeared in the LED panel inside the door but only shows the letter F, any ideas what the problem may be?


... Creda Dishwashers

I have a similar problem to another person. The drain on the dish drawer was blocked. The unit now shows an F1 error code ( flood?) and the pump runs continuously even after I've unblocked everything. I've tried switching it off for ages and drying everything out. When I switch it on again it shows the wash programme but then reverts to F1 and the pump motor runs continuously. Any ideas to cancel the F1 code?


The flood sensor on this unit is a PC board in the base, so you would need to remove the lower drawer and dry it out under there. If the base is dry and you still have the error, you can take a look at that sensor and clean any corrosion/minerals off ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

I have a Fisher and Paykel DW60CDX1 dishwasher, the display originally came up eith an error code for the door, which seemed to be the problem as it restarted with some pressure on the door, then it stopped again and now there is no LCD display and no action, cycle butten lights are on but will not make a noise when pressed. We live in the bush and cannot get a easy service option. Is there a diagnostics mode I can try, although the LCD may not work?


Old question, but for anyone else, hears the answer - http://www.recalls.gov.au/content/index.phtml/itemId/1015047This model has a product recall, minehas done the same as described above, recall issued Aug 2012. ... Fisher and Paykel 23 in. DS603H W Built-in Dishwasher

Bosch she4am Unit starts briefly, then stops about a minute into the operation and lights the CLEAN led. I located the diagnostics code paper, ran the test a few times, and come up with the same code...the CLEAN led lit indicates a door switch problem. I removed the door switch, it's a magnetic hall effect transistor..seems to work but not sure it's showing proper voltages. It reads 8vdc or so across the switch with door open, and about 11.7vdc with door closed. Seems too narrow a range to me


... Dishwashers

I have an Asco D3350 dishwasher. When the cycle starts the machine fills with water and when there appears to be the right amount of water in the machine an error code F4 shows on the panel. 3 clicks can be heard during the first 5 seconds of the F4 code showing. If I cancel the cycle and start it again it pumps out the water and then fills again and the code returns. Any ideas?


... Asko 24 in. D3350 Dishwasher

HI, We have a Meiko DV 80.2, with a recurring error code of 204. I changed the booster level switch, and it worked for a while, but is now showing the same error 204. Any ideas Please ?


... Meiko Dishwashers

Code F2 I just replaced the door switch on an inoperable DD-602. My top drawer was working fine, but my bottom one has been offline for a while (door switch failed and I never got around to fixing it since I had the top). Well, my top finally failed too so I replaced both switches. Looks like everything is good on the top, but my bottom is erroring with an F2 code now. Kindof makes a thumping noise as it starts the cycle -- maybe 3-5 short thumps and then a 10 second delay, repeats. Any ideas? C


F2= \015\012The motor has not\015\012been sensed rotating\015\012\003 Foreign object has jammed the rotor\015\012\003 The rotor has failed\015\012\003 The hall sensor has failed\015\012\003 The electronic controller has ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

Just purchased and installed the LG LDS4821 dishwasher, instantly got the OE error code when we tested it. After following troubleshooting tips and calling customer service, error code still not resolved. Hose is not kinked, hose is not clogged (as no dishes have even been washed in it), and it's level. Does anyone have any idea what we could do to fix this problem?


Try a test cycle with the end of the drain hose placed into a bucket. If the dishwasher does not pump out then, call for warranty service (In the US, find a ... LG LDS4821WW 24 in. Built-in Dishwasher

MY FATHER IS WORKING ON A LXIH HOBART. THE UNIT IS SHOWING ERROR CODE E173. IS THERE A WAY I CAN FIX THIS PROBLEM OR A WAY TO GET THE ERROR CODES.


Hi,\015\012\015\012This is what I found in the manual...and on a couple of other sites....Machine won't fill or won't fill high enough(LX18, LX30 display shows "E0," "E2," "E3," or "E4")1.Low water pressure — ... Hobart 24 in. LXIH-3 Built-in Dishwasher

I have a Bosch SGE63E05UC dishwasher that keeps intermittently showing an "E:25" error code. Occasionally it will get all the way through a cycle without going into error, but more often than not it will error and stop. So far the main control module in the front panel and drain pump have been replaced and the problem persists. All hoses have been checked and are clean (unit is only 1 year old) and drains well, when it does drain. Any suggestions?


... Bosch SGE63E05UC 24 in Builtin Dishwasher

E6 I have been getting E6 error message over and over again. I have had the machine to pieces, cleaned out the pump and hoses, and still the same problem. Occasionally, the error message changes to E8 or E1, but no matter what, I can't get it to work. Any ideas? When I start the machine, select any program and close the door after a short while the machine does not complete the wash cycle and I get the following message either: E1 or E2 will appear in the control panel Any suggestions Dave M


I had this problem and fixed it tonight. When selecting a program water pumps into the machine, but with no drain i ended up with too much water and error code E6.\015\012\015\012I traced the fault to a broken wire between the electronic ... Smeg DWI614 Built-in Dishwasher

I have an LG Dishwasher model LDF9810ST. Error code E1 keeps showing (Water Leakage Problem) NO water problems anywhere to be found. I have a hard time shutting down the machine. It has had a new MAIN BOARD, and a NEW MOTOR. This unit is not 1 year old yet. Any suggestions?


Are you draining the unit in the basement or under the kitchen sink?\015\012\015\012If you are draining the unit to the floor you will need a new drain hose with a syphon breaker. This drain hose is factory installed on all new LG dishwas ... LG LDF9810ST Built-in Dishwasher

HE error My LG LD-14aw1 is showing HE error code - Heater Circuit is troubled???. (Not as much as owner!!!). I have repaired several dry solder joints in the control module, which have been causing various operating failures, but the HE problem has got me stumped. Can anyone provide me with a wiring diagram of the machine and or the control module? I'd like to trace the heater circuit to see if I can find the fault. Many thanks


From the manual: Errors: HE: Heater circuit failure.Please call your Authorized Service Center or LGECustomer Service at 1-800-243-0000(US), 1-888-542-2623(Canada). ... LG 24 in. LD-12BW5 Free-standing Dishwasher

Belling IDW604 Hi, I have an error code E4 showing on this machine any ideas on how to fix it?? it seems the pump is wanting to start but then does not I cant see a block in the tubes and I want clean dishes!! Any ideas would be gratefully recieved Rebecca


I found the solution myself. On the bottom plate, there is a float and a microswitch, when the water leaks onto the bottom plate it raises the float and activates the microswith which shuts down the machine and shows E4 on display. To get rid of the ... Belling 24 in. IDW603 Built-in Dishwasher

Hi! We just installed our LG LDF8812WW built in dishwasher. We ran our first cycle and after the wash cycle the dishwasher displayed error code OE. I read that it meant there is a problem with the drainage, and to check the hose if it is kinked. Well, the hose is not kinked and we have no idea why it would have a problem with the draining. We have the hose set up per the installation instructions. How can we check to for something clogged? Any suggestions?


I actually own an LG LDF8812 myself, except mine is stainless steel, not white. So be it. :-)\015\012\015\012Anyway, it sounds like you have just unboxed the unit and it is brand new, not just new to you. I am also ... LG LDF8812 Stainless Steel Built-in Dishwasher

Smeg DF410SDX problem with Lights 5 and 6 stay on! nothing works, can not get any other settings to work! any ideas, nothing is mentioned in the manual about these error codes. thanks for any ideas


... Dishwashers

My whirlpool adp 750 has error code 4, the manual says it's maybe overfilled and there may be a problem with the water inlet,but even when I reset the machine, the error stays and the machine is b


... Dishwashers

Asko 1895 New out of the box been in storage while the basement was finished. flashes door interlock error 4 lights left and the 4 lights right. book says close door. it is closed any idea what the problem is.


First make sure your door switch is making proper contact.If not replace it. If it checks out ok than your main control board is bad. ... Asko 24 in. 1895 Built-in Dishwasher

Have a 2+year old LG LDF6810ST dishwasher that shows no error codes but is not cleaning like it used to. Have city water, do not leave excess food on dishes when loading, am only using powder after reading other tips about the use of gels. There is excess moisture in the tub and on dishes after the cycle. Does not appear to be drying as it previously did. Any ideas?


Try these things in order:-Try to use a name brand powder, rather then a generic. Even a small box. I had similar problems with my LG dishwasher when I tried to save money by buying a generic powder. My dishes did not get clean and whi ... LG LDF6810ST Stainless Steel Built-in Dishwasher

My lg dishwasher LD-14AW2 is not starting. It turns on and displays the time but when I click on anything it double bings and nothing happens. I have cleaned out the filters and my husband has removed the drain hose from the s band and it was all clean. the display looks normal...no error code. Do you have any idea what the problem could be?


Tunr power off 20 min then back on see if this helps ... Dishwashers

Hi, I have an Electrolux ESL4115 dishwasher. There is power to the machine. There are no fault lights showing and the programme selection won't move from the 65 degree programme. When I close the door to start it nothing happens. Any ideas what the problem is please? Many thanks


... Dishwashers

Dishwasher will not run and its showing a code of tE. Any idea what the problem might be ?


The thermistor is located between the terminals of the heater and comes as part of the heater assembly. You will need to pull out the entire dishwasher to replace it. The heater assy is stuck into the side of the sump,you can access it fr ... LG LDF6810ST Stainless Steel Built-in Dishwasher

Flashes an error code indicating a heater problem -- element looks good. what part may I need? Is it worth the price to fix, or should I replace the dishwasher?


Check the heater or the thermostat. If you have nothing to check them with remove and have someone with a meter check them for you . ... Kenmore 24 in. 17032 Built-in Dishwasher

Hi, I have Kenmore ELite 630.1630 (made by Bosch).. a. can i get a repair manual? b. problem (just last few days.. there is a rough residue (seems like soap) left on all (glass and st. steel). This comes out if I scrub it under the sink with water. c. Tried the test cycle from Bosch website.. it ends up with a code H. Any idea what may be going on?


Hello,\015\012\015\012Welcome to FixYa,\015\012\015\012The "H" indicates a heating fault has been detected, and based on your post it is likely the heater relay in the control itself.\015\012\015\012Th ... Dishwashers

I have a dishdrawer (2) and following the use of a dishwasher cleaner, the bottom drawer appears to have developed a blockage. It will not empty, gets to the pump out part of the cycle and shows the red error code F3, to which there is no reference in the trouble shooting guide. The top drawer has also developed minute leak, sufficient enough to leave dribble marks on the lower drawer and over time, a white deposit on the floor. Is there anything we can do for the blockage problem before reso


Remove the small basket from each drawer and lift up the removable plastic cover and take the drain filters out , empty them of food by products and try it again.. If you've never cleaned them then that's your problem with the drain process.. Hope th ... Fisher and Paykel Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1546 seconds