Having problems with your Crosley Dishwashers ?

CDU510V I have removed the torax screws to remove and clean the sprayer unit. How do I release the arm that rotates and sprays so that the whole part comes out?


Answers :

Repair Help & Product Troubleshooting for Crosley Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

CDU510V I have removed the torax screws to remove and clean the sprayer unit. How do I release the arm that rotates and sprays so that the whole part comes out?


... Crosley Dishwashers

My Kitchen Aid KUDS01DJSS0 seems to have water going to the upper spray arm (I see water coming out of the unit just beneath the upper rack), but the pressure doesn't seem to be high enough to clean the upper rack. No evidence that water is coming out of the spray arm on the very top. Lower rack dishes seem to clean OK. I have already removed the whole upper spray arm assembly and inspected the flapper valves that the middle sprayer goes into. I suspect that it's not making good enough contac


... KitchenAid Dishwashers

Dishwasher Repair Dishwasher is a Stoves/Newhome DW616 Rotating spray arms do not always operate. This is an intermittent problem - will sometimes work normally for a few days then arms will not move at all with no water coming from them. Machine appears to go through its normal cycle. Some times cycle starts normaly and spray arms stop working part way through.


It could be a motor or a pump issue. The dishwasher has a motor that attached to a pump which forces the water up into the sprayer arms and during the drain cycle, it pushes the water out of the dishwasher. \015\012The motor (and pump) located beneat ... Dishwashers

Kenmore dishwasher model 665.16033401 doesn't drain well. Drain pump comes on but drain water only trickels out slowly. Obstruction somewhere ? Removed rotating spray arm inside to try & get at the place where the drain water enters pump. Can't remove any parts beyond spray arm. Home: 330-865-4813 Cell: 330-608-3022


... Dishwashers

GU2700 Whirlpool - Does NOT FILL 2 Gallons on INITAL FILL - unit has new parts FILL VALVE IS NEW OVER FILL SWITCH IS NEW while filling if you reach under the unit and push the over fill float up it turns off the fill cycle - if you let go - unit keeps filling - but does not add the correct 2 gallons - water is not even close to the heating element - does not have enough water to come out of the TOP SPRAY Arm


... Whirlpool Dishwashers

My Kitchen Aid KUDS01FLSS2 dishwasher does not spray water thru the wash arms nor do they seem to turn. Additionally, one of the the bottom arms hits the "cap, internal rear feed" where it clips to "feed tube assembly" when rotated by hand. The spray arm assembly appears true on visual examination. The unit fills, cycles and pumps out in an apparent normal way. While on this site a while back I was advised to clean the unit and referred to a downloadable repair manual that was, in fact, not


Hi.The fact that "one of the the bottom arms hits the "cap, internal rear feed" where it clips to "feed tube assembly" would suggest a tubing problem. However there are more faults that will result in no spray. Testing in this case can be ... KitchenAid Dishwashers

Mod #: MDB6600AWB Ser #: 16505148CG No water comes out of spray arms, checked and cleaned filter-OK. Wash impeller is cracked where it slides onto the hexagon rod but it you take the filter flow plate off and put the impeller back on, when you put the unit on rinse only and quickly open the door you can see it is still turning and moving the water. The unit still fills and drains. it just does not have enough force with the impeller to force the water into the spray arms.


Hi,\015\012 \015\012Please check the bellow link regarding your query....\015\012 \015\012 ... Maytag 24 in. MDB6600A Jetclean II Built-in Dishwasher

My dishwasher's top rotating sprayer keeps coming loose. The screw and plastic bearing fall out and I think that it has stripped out the end where it seats into the top of the washer. Any ideas on how to anchor this in? Adhesive? A larger screw? The plastic bearing is Part No. 568 and the screw is Part No. 569. If I replace the conduit arm (Part No. 585), will that give it a new, clean spot to screw in too? How difficult is it to replace this arm?


\012Hi,\012That is not that hard to fix and you can easily buy the parts yourself online...Here is a tip that will help you with the online buying...How to Buy ... Dishwashers

The spray arm, above the top rack, keeps unscrewing during the wash cycle. Just the arm comes off leaving a round plastic part attached to the top. This can be unscrewed and inside is a white 'washer'. The arm can be clipped back but comes off again in the next wash. The plastic 'washer' has to be turned over to allow re-attachment. Is a washer missing from inside?


Could the arm be mounted upside down and rotating the wrong way? Just an idea... Some of these can fit either way and the retainer will fit either side of the arm. ... Frigidaire 24 in. PLD2850 Built-in Dishwasher

I have a mod. GSD2200G00WW . It has low water level and not enough pressure to turn the spray arm. When first starting i see water coming in but not enough. I added water in manually with a container and turned on and the spray arm rotated fine. I closed the door and turned back on and the water drained out of it instantly back to a low level. What now?


... GE Dishwashers

My Kenmore Elite dishwasher 630.1630 9400 (possibly made by Bosch) has a bottom rack spray arm a top rack spray arm and a missing sprinkler on the outlet at top of unit (ceiling it the cavity was a room). What part number is it? Can I post a picture? thank you


... Dishwashers

The door would not shut. We checked all around and nothing was blocking the door from shutting. We determined the latch on the door was not releasing. I forced the door shut. The touchpad works...lights come on but unit will not operate. The release handle on the front just wiggles back and forth without effect. Lowes says it is one of three parts...none returnable. Any thoughts on what part and whether this is something average consumer can self fix? Thanks.


Hi,\015\012 Lowes is right regarding the parts needed.\015\012\015\012First check the strike part is ok - that's on the body of the machine not the door.\015\012\015\012Unplug the machine.\015\012\015\012Remo ... Whirlpool DU1055XTS Built-in Dishwasher

I have a Bosch dishwasher and the upper arm that spins and dispenses water has come off. There is a bracket on the back wall with 2 protruding pieces and an open whole in the middle which seems like the water comes out of it. There are 2 metal "clips" on the side of this braket which seems like the plate part of the spining arm should be able to attach to it.. I cannot figure out how..Any helo would be apprecated..


On Bosh dishwasher you just slide the upper arm vertically until it snaps in place. The arm attachment will snap automatically into the clips, onto upper dishrack, unless the upper arm is damaged ... Dishwashers

Kenmore (Whirlpool) 655 1589910 Dishwasher. Fills with water, motor makes horrible noise (buzzing / loud hum). Dishes do not wash and there is no evidence that any water pumped up to the spray arms. Spray arms are not clogged. We have a fully functioning water softener so it is not a hard water issue. Unit does drain normally. Either filter is badly clogged or pump is bad. How do I get to these parts to check them out?


You need to clean/ check the chopper. sounds like you have a bad motor. about 2-300 dollars for the part ... Kenmore 15899 Built-in Dishwasher

I had a service tech at my house to repair my refrigerator. He also took a look at my Maytag WU504 dishwaser, which was not cleaning the dishes anymore. He was less familiar with dishwasher diagnosis, but found that the lower spray arm was pumping out water through the jets properly in the cycles, but that the spray arm was not rotating. He seemed stumped and called his supervisor, who suggested it might be the wash impeller. I have looked at the parts diagram on partselectdotcom and taken t


You are absolutely correct!!\015\012\015\012The support retaining nut allows the arm to spin without falling off.\015\012\015\012And it would definately cause dishes not to clean if the arm didnt rotate.\015\012\01 ... Dishwashers

Kitchenaid dishwasher - small pieces of food are left on otherwise clean dishes. Water level comes to about 1 inch below heater coil. I ran it without dishes (or soap) and added about a quart of water so that level came to about 1/4 inch below heater and that's when I noticed food pieces on drain surfaces (nylon filter under bottom spray arm unit and circular plastic "trap" surrounding it). Spray arms holes are clear and water is hot.


It sounds as if you figured the solution out. The holes in the spray arm(s) get plugged by small debris, (tooth picks, seeds, bits of plastic like candy wrappers, etc) and the water does not reach the dishes to wash and rinse effective ... Dishwashers

The top-most spray arm, on the ceiling of the dishwasher, comes off during most every single wash. I can unscrew the piece left up there, adn snap the arm back on, but it's not sturdy and falls off again the next cycle. What new part do I need to get so this arm stays in place?


... Frigidaire 24 in. GSB5712B Gallery Supreme Built-in Dishwasher

Fisher & Paykel DW60CDX2 spray arms do not start rotating after turning dishwasher on. Nothing stuck and I can rotate it freely with my hand. No error code comes up.


... Fisher and Paykel Dishwashers

I have a De Dietrich DV640JE1 built in 45cm Dishwasher, working fine for over 3 years. After replacing the connection under the sink to fix a leak it has stopped working. But I dont think this is related. I run a cycle and it fills water in the bottom of the machine, it drains it out in the end but the 2 arms are not rotating and no water comes out. I checked the arms and they are not blocked. A faint clunking sound can be heard at some part of the cycle. I did also run a cycle with the dr


Hello Benny,\015\012\015\012It's highly unlikely that replacing the connection under the sink is related to this problem.\015\012\015\012From the symptoms you describe, it's almost certain that the circulation pump motor has f ... Dishwashers

The unit goes through its cycles but the top rack is not getting clean. The bottom spray wheel works, the middle and top spray arms are getting water but it seems not enough to make them rotate. The pump screens are clear and there seems to be enough water. Whats going on?


The problem is likely to be that the jets in the rotor arm are blocked.\012\012To check this, remove the arm (it is easy to do, as it is intended for the user to do this) and clean out all the holes. Try running water from you tap through ... Dishwashers

How do you remove the lower spray arm on a Kenmore Ultra Wash (665.17019.402)? I was told to hold on to the plastic screw and spin the arm counterclockwise to remove, but I've been spinning and spinning, at leat 100 rotations, and it is not coming off. I've uploaded pics so you can see the apparatus. http://picasaweb.google.com/gregoryor/Dishwasher?feat=directlink


Hi, In the center of the spray arm is a threaded piece of plastic/bolt.\015\012Use pliers and turn that tab on the bolt. If it doesn't turn easy. Holt the bolt and try to turn the spray arm with you hand.\015\012It will release the spray ... Dishwashers

Gallery 900 Series dishwasher : middle spray arm is not rotating. I don't think water is coming out of the nozzle and upper spray.


... Frigidaire Dishwashers

NEED PARTS TO HOLD UPPER SPRAY ARM ON MODEL: FDB4315LFSO WHITE INSERT WILL NOT LOCK INTO THREADED UPPER UNIT?? PC MISSING ??ARM ISELF IS 9" LONG AND HAS NUMBER 1644681 ON IT. ONLINE SITES CAN'T IDENTIFY IT?


... Frigidaire Dishwashers

The diswasher arm does not rotate or spray water


Check the small holes on the spray arm. They are most likely plugged. (candy wrappers, tooth picks, popcorn or watermelon seeds, you name it.) Sometimes you can clear the holes out, other times it is just as easy (and not very expensi ... GE 24 in. GSD2000Z Built-in Dishwasher

Figidare dishwasher Upper arm not rotating, no water coming from top hole to fill upper arm.Lower arm rotates shoot water up cleaned filter screens. Check ball seems ok by pump, is there a location it (ck ball) should be? My upper arm is not rotating, things are coming out crusty, and it's definitely not getting water to the upper arm. My check ball seems to be plugging the tube the water goes up in.


It seems other posts were correct - The upper arm doesn't spin all the time. Once I learned that, and let the dishwasher cycle through, I saw that the upper arm does spin. So, there wasn't a problem with the upper arm afterall. That doesn't solve ... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1422 seconds