Having problems with your Danby 22 in. DDW396 Free-standing Dishwasher ?

Will not drain the water out.Between cycles or at the end

\015 I have a danby countertop dishwasher \015\012model # ddw396w\015\012everything is still working fine but the water doesn't drain between cycles or at the end.Not draining.I have cleaned it thoroughly but still nothing\015\012Is there a part that i can replace ?Please help\015\[email protected]\015

Answers :

This might be to simple but if the pump seems to run then check the tubes for any way that it might be blocked bends, blocks, ect. If the pump is not running, check out Sears Parts Online. They have just about every part for Danby. Put in your model number and choose a sub component with what you need.

Good Luck!
-Dustin

\015\012

Used the advice from kurtisdigita as well. I couldn't find an easy way to remove the motor without taking apart much more than the main metal wrap-around cover, so I just sprayed the axle areas (behind the white plastic knob) liberally with anti-seize lubricant (basically, it's like WD-40 with graphite). Attached is a picture of the motor.

mooboynyc_1.jpg
Repair Help & Product Troubleshooting for Danby 22 in. DDW396 Free-standing Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Hotpoint dishwasher machine go's through wash cycle, through to the end, after dry cycle ends there is always 2 inch's of water left in it that doesn't drain out' but some water is added when new cycle is started, then throughout wash cycle whenever water drains it never drains completely, always leaves 2 inches of water before adding more water to begin rinse cycle. what do I need to do?


... Dishwashers

Kenmore Ultra Wash Quiet Guard - will not drain at end of cycle. After cycle is complete, water (not clean) sits at the bottom of the washer but I still unload the dishes and then turn the cycle dial around again - going past all the water heating and filling and washing - and land on the drain cycle, it will drain. Any ideas why it will not drain when I let a cycle run, but will drain once I cycle it through to the drain option?


... Frigidaire 24 in. PLD2850 Built-in Dishwasher

Kenmore elite dishwasher model 665.13153k701 At end of wash cycle, water does not drain completely. Intemediate drains during wash do drain completely. rinse and hold drains completely. watching water at end of wash thru disposal, water flow cuts off like valve closed. other drains taper off


... Kenmore 24 in. 17482 / 17484 / 17489 Built-in Dishwasher

My G832SC is not draining at the end of the cycle. It runs the entire cycle, and the dishes appear to be clean. The soap dispenser has opened and the dishes are rinsed. However, the dry cycle doesn't run because the machine doesn't drain at the end. The intake/drain light is flashing. If I reset the machine and start a new cycle, it will perform an initial drain and the water level does go down. We checked the tri-filter and the valve pump thing, rinsed both. Checked the hose under the sink. We


... Miele Slimline G832SCi Built-in Dishwasher

Hello, I have a Neff Dishwasher S5453X1GB/74 and it's not draining the water out at the end of the cycle. I have unscrewed the filter and released the impeller. I have also cleared the waste pipe that runs to the sink waste and put loads of cleaner in the dishwasher. The pipes seem to be clear as water goes somewhere during the cycle but backs up at the end. A few times when I started a cycle the water did not spray out but I could here the drainer or motor? running. I jetted water through th


... Neff 24 in. S5453X1 Built-in Dishwasher

Kitchen Aid dishwasher Model# KUDP01FLSS. 2 problems #1 Won't run unless you press in on the door and hold it for a few minutes then it runs through cycle normally. Problem #2 It won't drain water out at the end of the cycle when I open the door there is water laying in the bottom of the tub. I have checked the drain hose for clogging and it appears normal. I am able to remove the hose from the disposal and suck the water out of the tub using a shop vac this indicates to me that the drain is ope


... Dishwashers

I have a Kenmore dishwasher, model 665.17019401 (serial number FS1002610). It goes through all cycles, drains out water, periodically, and dries the dishesat the end. But, when it ends, there is water at the bottom of the tub, at least 1 quart of water. I have to drain out the remaining water in the dishwasher. What is wrong?


Either the drain or screen is somewhat plugged, or a clog or jam in water pump. Many machines do leave just a little bit of water just so the sewer fumes don't come up. ... Kenmore Dishwashers

Water will not drain out of bottom of dishwasher.It will go through the whole cycle but will not drain. This is a Frigidaire model no.FDB510LCS3 Serial no.is:noth70219331.Pump hose was disconnected and drained completely,dishwasher was put through another cycle and still ended up with water puddled in the bottom!! Could this dishwasher be called a lemon??? Does the pump need replacing?? I have noticed on your website that many others are having the same problem.To me it appears that it may be sh


Check the input to the drain hose to make sure it is not blocked by something like a cherry pit.  That could cause the water to not drain fully. ... Frigidaire 24 in. FDB510LC Free-standing Dishwasher

I have model 363.14779100 that has a problem. When a drain cycle is at the end and the fresh water starts coming in, the draining won't stop therefor all clean water goes right back out the drain. I can open the door latch and reshut it and the cycle will complete but the same thing happens on the next drainout. Is there a switch that needs replacing??


... Kenmore Dishwashers

GE GSD4920Z dishwasher. Problem is that it does not drain completely at the end of the cycle--about an inch of water remains. After checking for clogs, etc, we followed a troubleshooting procedure which involves a hard reset (power off, then reset twice at beginning of cycle) and this procedure successfully drains the tub. However the next time that it's used on a normal cycle, water remains again. Suggestions?


Hi\015\012\015\012\015\012\015\012Thanks for using FixYa.\015\012Dishwasher not draining properly or not draining at all issues can arise due\015\012to different reasons. Usually, these issues are related to kinked hoses,\015\012knocked o ... GE 24 in. GSD4920Z Built-in Dishwasher

Holding water There is water in the bottom of the machine after the cycle is done. There is definitely draining going on throughout the cycle, but it's not draining completely at the end -and the water that is left is murky. Spoke to a friend who tells me it sounds like the dump valve, but in checking on line, that doesn't seem to be a part that even exists any more. Do I need to buy a new dishwasher? This was not in the budget this year... Thanks for any advice! Nancy


Are the dishes getting clean at the end of the cycle, if not then there could be foreign debris in the pump housing that can cause this, needs to be dismantled and cleaned out, if dishes are clean then the pump impeller will need to be replaced ... Whirlpool 24 in. DU1100XTP Built-in Dishwasher

When washing dishes, the washer drains okay at the end of the cycle. However, ir seems that for some reason in the mornings we are finding water in the bottom of the dishwasher--sometimes so much that some has leaked out to the floor. When the drain cycle is turned on, the water goes out okay? Any advice?


Sounds like a bad fill valve. ... Kenmore Dishwashers

Hi: I have reviewed the forums and tried to fix this issue. Have a Miele G2120 dishwasher that at the end of the cycle - the three (rinsing, drying and end) orange lights begin blinking in harmony. I have removed the triple filter, and two plastic parts to the impeller and made sure all was free of obstruction. I then pulled it out removed the drain hose from in-sinkerator; removed the water line and checked for obstruction. When it gets into this condition - the majority of water drain


Hi The issue seems to be with the float switch assembly that is bad and should be replaced. Float assembly is found inside the dishwasher's tub, on the bottom. The water that ... Miele Inspira Series Dishwasher w/ 6 Programs and 5 Temperatures - G2120 / G2120BL - Blac 24 in. Built-in Dishwasher

There is a pool of water at the bottom of the dishwasher that wont drain out. nothing seams to be clogged. This happens in every cycle. If I drain the water manually as much as possible at the end of a cycle it will be there again after the next one. Thank you for your help.


... Viking Dishwashers

Draining problem Water left in dishwasher after end of cycle. Have a disposer, don't have a drain air gap that I can see. Tried to do a cancel/drain, showed 2 minutes ended and water still there. Disposal works fine. What is really interesting is that there is only two of us and at most we've only used the dishwasher thirty times since we had it. Of course- service plan ran out last year (July 07) Please help me. My name is Donna


There is a flapper in the drain hose just where the hose attaches to the pump assembly it has been know to get dislodged and cause a partial drain. With towels underneath hose remove drain hose and stick you finger in and see if it is free moving. ... Kenmore 24 in. 16539 Built-in Dishwasher

The dishwasher does not appear to be draining properly any more. There is soap residue on the door after it runs. Also ther s a small pool of water by the food drain after the cycle ends. The glasses all have a residue on them after the washing cycle ends


Hi,The scum, film and white\012residue problems have started since the reduction of\012phosphates in dishwasher detergents.Here is a tip that\012will help you to solve the problem of films, residue, and scu ... Asko 24 in. D3121XL Free-standing Dishwasher

Hello , we have a blanco BFDWC65 dishwasher supplied to us by our builder , The dishwaser fills with water ok then once in cycle it starts (with all operating lights ) then stops , it continues to start then stop for the rest of the cycle , Quiet some time later it finished and then drained the water ok , now it struggles to get to the end of the cycle. have checked all filters , water pressure and for clogged hoses , everything is ok in that department. Any help would be apprieciated


I would suspect the control board in this type of behaviour. As the machine is new I advise no interference, but to open a claim under warranty. You would have all the warranty papers for this unit, or should have received them from your builder. The ... Dishwashers

Kitchenaid KUDP01FL : Hi, machine will start to fill (on heavy), and then will not engage into the wash cycle. Have to press cancel to drain water. All other settings ( china/rinse/ normal wash) when button is pressed and door closes will "click". No water fills into machine. Have to press cancel to end cycle. Can it be a bad connection being i tryed trial and error and banged on inside of door to maybe "fix" it. NOW, heavy cycle does not fill with water, just a "click" noise. Thanks for


... KitchenAid 24 in. KUDP01FL Built-in Dishwasher

Bosch SGS5312GB/12 Dishwasher I had a control board. Worked fine except didn't heat the water. Got it repaired (new PCB). Now the only thing it does is drain. Clicks every 20 secs and carries on draining. Got a new board. Does everything (including heat the water) except it does not drain before, between, or at the end of cycles. It does drain when while filling, and if the flood detection rod is raised manually (also drains if the inlet pipe beyond the pressure sensor is blocked - found


... Bosch Dishwashers

I have a built-in Bosch dishwasher SHU 4302 UC. It no longer drains the water out at the end of all the cycles. I have tried everything mentioned in the booklet (make sure water is hot, use the jet-dry stuff, make sure outflow hose doesn't allow water back in). I have to siphon out at least a good bucketful of water. (Also, only the regular wash cycle works, which is fine with me.)


The problem is a solenoid on the bottom of the unit. It is a small black cylinder next to the pump. It operates the valve that changes to the drain cycle. You can probably order one from Bosch ... Bosch 24 in. SHU43 Built-in Dishwasher

Ge profile dishwasher not draining Model no. pdw9280n20ss I checked the drain line at the garbage disposal. No blockage. Line is clear. The back flow loop is high and not kinked. Only a small trickle of water comes out of the disposal drain at the end of cycle. No forceful pressure of water like before. I removed the smaller grill drain area and cannot feel any objects down in there. I do not know how to remove the larger fine mesh grill on bottom. Any suggestions?


Did you ever figure out how to remove that large mesh bit? I am stuck at the same spot and would love a hint. ... GE 24 in. Profile PDW9880JSS Built-in Dishwasher

My trusty Bosch s510 Dishwasher which has been going strong for about 17 years (at least) has just decided not to empty itself. I noticed the bottom was full of water after a wash. I emptied all the water out by hand and presuming there is a blockage in the drain tried using a plunger to unblock it. I have since put it through another cycle and half way through water started leaking out of the front. At the end of the cycle the bottom of the dishwasher was again full of hot 'soapy' water. If th


Same problem, so went out and bought a new bosch. Problem with the S510 was cured by lubricating the pump out motor bearings with a squirt of WD 40. If you don't know which pump, follow outlet hose to pump outlet.Les ... Bosch Dishwashers

At the end of the cycle the water is not draining out of the tub. I vac'ed out the water, removed the filters and checked for debris but found non.


Check drain hose first.If you do not find any blockage, then you will need to access the pump, remove pump hose and look for blockage in there.If there is no blockage at all, then either the water level switch, a faulty pump ( ... Bosch SHV46C03 Built-in Dishwasher

My DFS1500 S Beko dishwasher won't end the final cycle, the pump is working normally it drains the water, but it doesn't stop, I have to turn it off or it will not stop by itself, it sounds like its draining water except there is no water in it.The dishes are salty and white.


... Beko Dishwashers

I have a De Dietrich DV640JE1 built in 45cm Dishwasher, working fine for over 3 years. After replacing the connection under the sink to fix a leak it has stopped working. But I dont think this is related. I run a cycle and it fills water in the bottom of the machine, it drains it out in the end but the 2 arms are not rotating and no water comes out. I checked the arms and they are not blocked. A faint clunking sound can be heard at some part of the cycle. I did also run a cycle with the dr


Hello Benny,\015\012\015\012It's highly unlikely that replacing the connection under the sink is related to this problem.\015\012\015\012From the symptoms you describe, it's almost certain that the circulation pump motor has f ... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1186 seconds