Having problems with your Dewalt 3800 PSI Pressure Washer ?

Dewalt Pressure washer keeps shutting off for no reason. plenty of gas and oil, water running to it. starts fine and as soon as I start spraying it shuts down.


Answers :

Repair Help & Product Troubleshooting for Dewalt 3800 PSI Pressure Washer

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Dewalt Pressure washer keeps shutting off for no reason. plenty of gas and oil, water running to it. starts fine and as soon as I start spraying it shuts down.


... Dewalt 3800 PSI Pressure Washer

I have a Craftsman power washer model 580 752020. When I start it up, turn on the switch the electric motor runs fine until I either close the trigger to the spray nozzle or press the trigger for power spray. The electric motor just shuts down, if I take my finger off the pressure and let the water run with no presssure the motor runs fine. My question is this. Is the capasitator on the electric motor the probable cause and is there a way to check out the capasitator to see if it is malfuncti


I doubt that it has anything to do with the capacitor on the motor. i think you are having a problem with the actual Motor Drive circuitry. What is happening is when you close the switch, this tells the Motor to "Ramp Up" to pump the water out, what ... Craftsman Pressure Washers

My pressure washer is bogging out and shutting off. It will run fine for a bit then it starts sputtering and shuts off. I changed the oil right before this started happening and yesterday i changed the sparkplug and it seemed to be working fine until I used it today on the driveway.


SOUND LIKE FLOAT IS STICKING ... Dewalt 3800 PSI Pressure Washer

My pressure washer starts fine, shoots water OK. After running for 5-10 minutes cleaning siding I shut off machine. I go to start it again within a minute or two and the thing feels like it's just about seized. If i wait until the motor is completely cool, it will pull start freely and start right up. I think something is wrong with the pump, not the engine.


Your pressure washer may not have an ez-start valve installed from the factory. Without the ezstart valve, you will need to hold the trigger on the wand open to release the pressure to easily start your engine. This link will show you wh ... Briggs & Stratton Pressure Washers

When dishwasher is turned on to the cycle mode - it fills with water - heater heats water to the proper temp - pump starts - washer goes through it's complete cycle - even pumping out the wash water and the drying cycle,then shuts down. the problem is that it does not circulate the wash water thru. the spray heads-even though the circ,pump is running.Even though the unit is 8 yrs.old and hasn't run for 6 yrs,my wife&i do our dishes by hand. our unit is a GU1200XTKB0 Serial# FL4617501


The impeller on the wash pump is worn out or the disposer screen is obstructed. Disassemble as needed to investigate the cause. ... Whirlpool 24 in. GU1200XT Built-in Dishwasher

I have the two drawer model dish-drawer system. In the past the top seal leaked and since has been replaced with a new seal. Worked well for several years after but then the top drawer quit running. So we started to use the bottom drawer. That was fine for awhile althought it would pump waste water into the top drawer. Now neither drawer will work. The bottom drawer starts up and shuts down. I pulled the lower drawer and it is dry.


If your model has got an LCD display are you able to record what shows up on the display when the bottom drawer shuts down. If no display then are you able to note down the LEDs which are on inside the top of the drawer lid. It is likely there is no ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

PRESSURE WASHER RUNNING BUT NO WATER COMES OUT WHEN YOU PULL THE TRIGGER??? IT WORKED FINE WHEN I FIRST STARTED IT. I THEN SHUT IT OFF TO MOVE IT. WHEN I STARTED IT BACK UP, IT STOPPED WORKING.


The water admittance valve is stuck. The spring loaded valve lets more water into the pump when the pressure drops when you trigger the wand. Take the valve apart, clean the bore with crocus cloth on a dowel rod. Replace the O Rings and lube with ... Pressure Washers

Troy Bilt pressure washer model 020209 will not build pressure-have checked all screens and intake in pressure hose and garden hose from house to pump. water leaks at gun handle- took it apart and oiled piston- was ''grabby'' but now snappy but still leaks. Engine starts fine and runs fine. Please help.


A leaking gun will kill all the pressure. You may need to repair or replace the gun ... Briggs & Stratton Pressure Washers

The oil in my gc160 Honda pressure washer is getting water in it some how. Could it be something with the water pump gasket or what? And I can get it started but can't keep it running un less I keep spraying starter fluid in the carbar. Please help ?


... Karcher 2500 PSI Pressure Washer

I press start the water fills fine as soon as it start running i get a loud humming/ vibration and nothing happens?


Sounds like the motor is bad.after it fills the motor should start,has it been leaking under the bottom of d.w.rmove the bottom front panel and see if there's any water stains,usually the motor will leak before it finally dies. ... Frigidaire Dishwashers

NO PRessure i have a Honda gcv160 5.5 dt2400cs CRANKS RUNS FINE AS LONG AS TRIGGER IS pulled to let water trough it has no pressure soon as you let go pressure starts building then it kills the motor will not run unless you hold handel


Hi It sounds to me like your unloader valve is stuck, this is the thing that is meant to move up and down when pressing the trigger.Please remove the unloader valve assembly and check for damage. If no damage is found then grease and lubricate this p ... Honda Pressure Washer PSI 3000

Honda Trash Pump Model WT30X Stalling - 8hp engine runs for approx 5 seconds that shuts down, restarts after I hear a relay click ? oil is fine - so I do not believe that it is an oil pressure sensor. Are there any other sensors ? Does water have to be pumping through it??


Their is an oil level sensor that lasts around 3 months of use. unplugging it would solve your problem But replacing it is a night mare. and if your oil runs out It's all over. if not the oil sensor, and your spark is constant Check your fuel system ... Honda 8 HP Engine

Dishwasher malfunction MOST OF THE TIME it shuts itself down before fully filling with water - SOMETIMES it doesn't shut down until the minute the wash pump starts - SOMETIMES it washes for 10 or 20 minutes before shutting down - SOMETIMES it will even run a whole cycle, BUT it doesn't open the soap dispenser door - tried doing a diagnostic run but after it turned on all the lights on the panel it started to fill with water and shut itself down......... HELP


Follow this steps and fix it. God bless youFloat Switch\012\012\012The float switch may be hung up and this can cause the dishwasher to be stuck in a cycle. Check the ... Dishwashers

I have a F&P Model DD602I. I had a repairman out to change out hoses that were bad and now I have this problem: When I just run the bottom unit, it works fine, but a bunch of water ends up in the top unit that I have to drain out. If I just run the top unit, water collects in that unit causing a default. Now if I run both units together and I start the top unit about 3 seconds after starting the bottom unit, both units work fine! When I look at the hoses under the sink, they loop down quite a bi


Try to isolate the drain hose of the top drawer by disconnecting from the U hose. Run the bottom drawer. \015\012\015\012Similarly isolate bottom drawer and then run top drawer.\015\012\015\012See if problem is linked to back ... Fisher and Paykel 24 in. DD-602 Built-in Dishwasher

I have a Honda GC160 5 horsepower power washer with 2400 psi. When its cold it is easy to start but after it has been running for a while the only way to start it is to have the water shooting out of the wand. Once it is hot and running if i stop the stream of water (release the trigger on the wand) then the machine shuts off. It seems like the only way to keep it running is to constantly have water running through the wand. Please help


... Pressure Washers

Rkv 3.5G35 Pump is overheating so badly the plastic sight glass is melting. There was plenty of water and pump was running good until "back end" started overheating. Oil level was fine but it is now really black


... Annovi Reverberi RMV2.5G27D Pressure Washer Pump

I have a generac 2200 psi pressure washer. It starts and runs fine as long as I have the trigger pulled to spray water. When i let off the trigger it kills the engine. What could this be and how can I fix it? Model number is 01040-2


... Briggs & Stratton Briggs Stratton Pro Style Pressure Washer Gun Generac

Troy Built pressure washer starts up fine and idles nice. Start spraying and everything is fine for about 30sec to 1min then the engine just shuts off. Seems like pressure is building up and choking the engine out. If I dont spray it will idle all day long. I have cleaned the unloader area, still shuts off. I have the pump off the machine, what should I do? Model number 020208 Troy Built. Rev # 01


... Pressure Washers

Troy- Bilt pressure washer #020209 , 7.25 Briggs & Stratton, AR water pump #SJV 3G27-1. Boggs down an cuts off acts as if motor is getting tight with wand in use or not. After shut down its easily starts up an repeats itself. Removed pump motor runs fine.


... Briggs & Stratton Power Products 1539 Pressure Washer

Sears pressure washer mod#580-751781 7.8 hp /2500 psi / 3gpm Starts fine and runs for 15 seconds then shuts off. Changed out gas and oil still no improvement.


... Craftsman 2500 PSI Briggs Stratton Powered Pressure Washer

Gx240 honda engine starts fine, but coughs and sputters with heavy exhaust; then it runs smoothly for 2 to 3 seconds and then shuts itself off. I checked and there is plenty of gas and the correct amount of oil in the engine.


Sounds like it could do with a cleanout of the carburettor. Also check for dirt/rust in fuel tank that could be restricting fuel flow to carby. ... Honda 8 HP Engine

My troy built 2200 pressure washer was running fine but then shut off instantly I then noticed it had low oil I filled it but now it won't start


Pressure washer takes oil in two places:Pump oil is 20-30 weight SAE non detergent and comes half way up/ do not fill more than 1/2 way ... Briggs & Stratton Pressure Washers

New honda pressure washer maybe had it 2 years and only has about 3 hours on it, I was using it yesterday and it started fine and after running for about 10 min it shut down like i turned the kill switch, it has oil and gas but seems to have lost compression. It is a Honda overhead cam GCV 160, pressure washer is a Troy Built model


... Pressure Washers

Briggs and Stratton Troy Bilt gas pressure washer one year old. I can get water thru pressure washer and bleed the air, water comes out the hose just fine until I start the pump. Then, I lose all water flow. Pump runs fine but when it's running, no water goes through.


... Briggs & Stratton Prosumer 20324 Gas Pressure Washer

I have a Bosch SHU66C02. I opened the door to stop it from running temporarily, while it was sitting not running, it leaked all of the water out of the bottom right corner of the door, and when I went to start it later it just hummed but the timer didn't go down for over an hour. I tried to put more water in but as soon as I started I could hear the water added to drain. I turned the breaker in the fuze box off to it and let it sit for over an hour, but when I restarted, the timer was still at


... Bosch 24 in. SHU66C02 / SHU66C06 Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1910 seconds