Having problems with your Dewalt Pressure Washers ?

The pressure will build and slowly go dowe.the

\015 The pressure will build and slowly go down.the trigger can be released& it will do the same again the pressure will be good and slowly go down again. if you leave the trigger off too long the motor will die out.\015

Answers :

Clean out the nozzle.
Repair Help & Product Troubleshooting for Dewalt Pressure Washers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

The pressure will build and slowly go dowe.the


Clean out the nozzle. ... Dewalt Pressure Washers

My karcher 3100 professional pressure washer build pressure at random, when I take the nozzle of the gun the pump works when the nozzle is on the pump wont build pressure or if I hold the gun in an on possition after 5-7 min it build up the pressure, what is wrong?


... Karcher Pressure Washers

I have a troybilt pressure washer when i crank it up it builds pressure when i engange the pressure it takes about 5 seconds and pressure goes away if i let off the trigger it will build pressure again it only has about 20 hours of use on it (i did run a acid solution through it for my driveway wonder if that ate up a seal)


Unloader valve is the most likely suspect here.\015\012Remove and clean with penetrating oil then reinstall.\015\012\015\012Also add some LIGHT oil into your supply hose via a small funnel. 3-in-1 household oil or power steer ... Pressure Washers

My Karcher K3.450 won't build up any pressure - it oscillates on and off. It starts to build pressure, then the pressure drops, and it repeats the cycle over and over at a 2 or 3 second interval.


I fixed mine works good easy too watch my video step by step i put it on youtube ... Karcher K3.450 1800psi Electric Pressure Washer - -

I have a McCulloch FH160B power washer and it no longer builds up pressure. I haven't used this very much at all. I tore it apart and cleaned everything I could find. When i pull the trigger for the spray nozzle, I get line water pressure. When I release the trigger, the power washer sounds like it starts to build up pressure. When this was working correctly, the pump would shut off when the trigger was released. Any suggestions?


... McCulloch Pressure Washers

The Pressure Builds up the machine can't be maintained on, unless the spray gun is pressed. The pressure build up so much that it blew out a unloadervalve bolt.


... Pressure Washers

I have a Generac pressure washer, model #01450-0, with a Honda 5hp motor. The motor runs fine, but the pressure hose pulsates as if the pump is intermittently making pressure, and the pressure out of the sprayer is about half of what it should be. A friend suggested replacing the seals in the unloader. I bought an unloader kit, replaced everything and it still runs the same. It will build a small amount of pressure, spray for a few seconds, then the pressure dropps to almost nothing. Any help ap


Take a small diameter wire and poke thru the discharge hole of the spray head to clean out.\015\012Second time in 6 months that I had the same problem. The problem is alway in the spray head. ... Pressure Washers

How do I fix a pressure washer that will not build up pressure quickly and when it does reach high pressure, the pressure quickly drops to a lower pressure (more typical of the pressure found in a garden hose)


It can be the inlet filter where your garden hose connects is clogged, so check that first. Also make sure that the hose is connected tightly and not pulling in air both at the inlet and outlet. Remove the spay nozzle and use a pin to make sure it is ... Karcher G3025OH Pressure Washer

My Karcher K3.48M pressure washer remains in the low pressure mode even when I return the pressure nozzle to the high pressure position. How can this be corrected. The pump seems to build up the pressure because when I release the handle the pump motor stops. This is a fairly new pump which was purchased in the latter part of last year(2010). Could this have been caused by the detergent I have been using which is an automotive shampoo? Please help I love this washer and for the times that I u


... Karcher PSI Electric Pressure Washer

Pressure washer won't build pressure


The problem sounds like its in the handle.. trigger mechinism ... Honda Pressure Washers

2550psi Troy bilt with Briggs engine. Pressure washer runs ok and builds pressure. But, when the nozzle lever is depressed the pressure is strong and then drops to a much lower pressure and a fine spray.


... Briggs & Stratton Briggs Stratton 2550 Psigaspressure Washer

Pressure issues My pressure washer builds pressure and has a powerful first burst and then no pressure


Sounds like the pump is damaged; most likely from freezing. Needs anti-freeze if stored in cold temps. Repair or replacement of pump may be close to replacement cost. ... Troy-Bilt 020528 Gas Pressure Washer

Coleman powermate2000 pressure washer can't build up pressure


... Coleman Pressure Washers

Pressure won't build pressure


... Pressure Washers

Troy bilt pressure washer will not build or reach high pressure


Check the non-return valves in the pump block. if these are damaged or dirty you pressure will be greatly reduced. they are located behind the 3 lage brass hexagonal caps.\015\012\015\012I hope this helps ... Karcher 2500 PSI Pressure Washer

Pull my pump first startsthe pressure is good as soon as i pull the trigger the pressure is gone as long as i hold trigger just faucet flow let go of it pressure builds up until i pull trgger , no pre


... Annovi Reverberi RMW2.5G25D

Wgvb2122 pressure washer builds pressure until you pull trigger, then no pressure. Replaced seal kit on plungers, same thing! Replaced unloaded assembly, same thing! Every thing seems to be as it should be and clean. Any ideas before I shoot this machine?


... Pressure Washers

Troy Bilt pressure washer model 020209 will not build pressure-have checked all screens and intake in pressure hose and garden hose from house to pump. water leaks at gun handle- took it apart and oiled piston- was ''grabby'' but now snappy but still leaks. Engine starts fine and runs fine. Please help.


A leaking gun will kill all the pressure. You may need to repair or replace the gun ... Briggs & Stratton Pressure Washers

My karcher K2.98 pressure washer does not build up pressure. I checked hose and inlets and cleaned filter. Motor running fine, but no pressure.


... Karcher Pressure Washers

I have an Excell 2500 psi with Briggs & Stratton 6.5 HP engine that starts, builds pressure and maintains high pressure as long as the hose is not connected. But as as soon as I connect the hose, it loses all pressure. Is it the pump?


... Pressure Washers

Hi- I have a Simoniz S1600 pressure washer and usually when I first turn it on, the motor turns on to build up pressure. Now the motor won't kick in no matter what I do. Water still comes out of the gun as a small stream but there is no pressure. There are no reset buttons on the exterior of the machine. Thanks!


... Pressure Washers

NO PRessure i have a Honda gcv160 5.5 dt2400cs CRANKS RUNS FINE AS LONG AS TRIGGER IS pulled to let water trough it has no pressure soon as you let go pressure starts building then it kills the motor will not run unless you hold handel


Hi It sounds to me like your unloader valve is stuck, this is the thing that is meant to move up and down when pressing the trigger.Please remove the unloader valve assembly and check for damage. If no damage is found then grease and lubricate this p ... Honda Pressure Washer PSI 3000

No pressure i have a karcher g 2600 vh i wasnt getting pressure and i found that my spill valve was faulty it was actually broken i bought a new one installed it and im still not getting much better pressure ive taken the pump apart and checked for build ups blew thru the valves wirh the compressor and there appear to be no blockages


... Karcher G 2600 VH Gas Pressure Washer

My pressure washer won't build up any pressure. it will run water when you pull the trigger, but it is the same pressure as if the unit if not running


I'll assume you have an electric rather than a gas powered unit. First check the button on the plug to be sure the GFCI hasn't popped and be sure the outlet has power. With the water faucet turned fully on and the power switch on squeeze and ho ... Pressure Washers

Hi- I have a Simoniz S1600 pressure washer. Usually when I start it, the motor kicks in to build up pressure. Now it won't kick in no matter what I do. A small stream of water will come out but there is no pressure. There are no reset buttons on the exterior of the machine. Thanks so much.


... Black & Decker Pressure Washers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0691 seconds