Having problems with your EdgeStar Dishwashers ?

I just recived my portable dishwasher today and I had problems with it starting. I got it run after awhile. Now I can not get it to run again the power light comes on but the cycle will not start


Answers :

Repair Help & Product Troubleshooting for EdgeStar Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I just recived my portable dishwasher today and I had problems with it starting. I got it run after awhile. Now I can not get it to run again the power light comes on but the cycle will not start


... EdgeStar Dishwashers

My Miele G641 displays the Salt PC light even after filling it with salt. I have to cycle the main power switch 3 or 4 times before the Start light will come on. Then when I press the Start button it momentarily pumps out water and then stops. Sometimes the Start light stays on and I can get it to give the pump another brief spurt, but often the Salt/PC light comes on again and the Start light goes out. I then have to re-set the power switch. How do I tell if the logic board is fried?


Hi.This is not a PC, when logic board is fried the machine does not start at all rather than doing weird thing.The logic board is not fried, in the worst case the salt sensor is jammed. Try first pouring a couple of litres of hot wa ... Miele 24 in. Novotronic G641 Plus Built-In Dishwasher

I have a Frigidaire FDB956rbc0 model. When the start/cancel button is pushed nothing happens. There is power and other buttons cause lights above what is pressed come on. Delay wash works but when it starts the washing light flashes. I have run a test on the cycles by pushing start/cancel and power dry button during power failure mode. all cycle run properly. Any thoughts?


... Frigidaire Dishwashers

Maytag Dishwasher Model MDB4100AWQ When I start the Light Wash Cycle: Washer fills with water, heater comes on (I checked it with a volt meter--120 volts), timer runs, motor never runs, before the timer gets to "rinse" the heating delay light on the door comes on and the timer stops. The heater is still on (120volts) nothing further happens it just boils away on the water in the washer. Note: If I manually forward the timer to "rinse" the motor will kick in and run but does not pump out w


Most common d/w power is 120 volts, check for 120 volts with a  ... Dishwashers

My Frigidaire Dishwasher FDB1050RES2 gets stuck in a rinse cycle. The light on the front will be lit "clean" but the bottom of the washer is full of water. Opening the door does not turn off the "clean" light. For me to get it to run, I have to unplug it, plug it back in, push the start button until the ?washing? light comes on. I then push the start button once more and the dishwasher will begin to drain. I open the door as soon as I hear the water stop draining into the sink drain. This


By the descrition you are giving you will need to replace the main control board.Part number 154568401.you may also need to check the float switch.The part will run about 110.00 dollars from a local parts store ... Frigidaire 24 in. FDB1050RE Built-in Dishwasher

My Dishwasher starts, then stops after 30secs and won't continue draining. Everytime I turn it back on it comes up on the steam cycle and won't go to any other cycle, drains for 30secs and stops again. Power light is flashing. Have tried holding power button down for 10secs with no effect. Filter is clean, pipes are straight-no kinks. How do I get it to start working again? It is a whirlpool dishwasher, ADP5550.


... Dishwashers

Model KUDS30FXSSO, Unit attempts to start. Blue light on the front of the door comes on indicating the cycle is starting. Pump runs a few seconds as normal. Then the maching sounds like it trying to start the next step three or four times. The blue light goes out. The washing cycle then switches to cancel/drain, ( I opened the door to see which control lights were on.) runs the drain pump then stops. The green light on the front panel does not come on indicating the cycle was completed.


... KitchenAid 24 in. KUDP01FL Built-in Dishwasher

I own a KUDS01FLSS3 KitchenAid dishwasher. The lights on the control panel do not come on and a cycle can not be started. There is about an inch of water in the bottom of the dishwasher basin and it looks like the previous cycle did not complete. I have checked the wall outlet that the washer is plugged into and the washer is receiving power from the wall. And ideas? My next thought was to take the door off and check the power supply running to the door panel and control panel.


Servtek06 writes:\015\012check connections @ control board/module. May be Control Board/Module. ... KitchenAid 24 in. KUDI01FLSS Stainless Steel Built-in Dishwasher

I have a Whirlpool Gold Quit Partner III, model GU1100XTLB1. When I run the normal cycle it functions well until near the end. At that time the unit stops and the pots&pans indicator light blinks. If I hold the cancel button in the unit drains then refills and the light starts to link again. I don't know how to reset this unit because I only have air dry. If I leave the power off for a day I can get the unit to reset. If not, it just fills back up with water and the pots&pans starts blinking aga


... Whirlpool Gold 24 in. Built-In Dishwasher Dishwasher

Our ESD310 has a message of OP on the screen. It will come on and run on its own if the door is shut, counting down from 2. When I can get it to turn on and start a cycle it runs a bit, skips a bunch of time, runs a little more, and then skips time again counting down from 2. The high temp wash button will light up on it's own while running. The cancel button does not work. It acts as if it has a short, makes funny noises, and I'm afraid it's going to catch on fire.


... Haier ESD310 24 in. Dishwasher

Asko D3530 water inlet fault code, water valve is on, water comes in but after water comes in for a couple of minutes we get a (inlet water fault code) check power at circulating pump no 120v unit will not run reset system it will drain and start cycle again with same result


Hello,\015\012\015\012It is common for these valves to "appear" to be ok, meaning they begin to allow water into the unit, but then one of the two coils or plungers inside fail, or are clogged with mineral deposit from the water or other ... Asko 24 in. D3530FI Built-in Dishwasher

I have a Kitchenaid KUDIO1DL white dishwasher which is a few years old now but has worked great since I bought it. Today it has the lean light flashing and will not turn on. there is power, and the drain button seems to work, but I can not get the cycles to come on. When I press the start button, I just get two dash lines and then the unit turns off. Thanks


... KitchenAid 24 in. KUDI01DL - Multiple Color Built-in Dishwasher

Pots/pan light blinks alternately with the normal wash button. Sometimes the cycle will start and then the lights come on. Once they start blinking, the cycle stops and I can't get it to start again. Unplugging it for a few days has worked a few times. But it just keeps getting more frequent. If it does start up, it heats fine and washes perfectly.


... Whirlpool DU1055XTSQ Built-in Dishwasher

When i push the start button,it doesn't light up and start. The normal cycle and the other cycles lights work but it won't start. If i push hi-temp wash and heated dry several times, all lights will come on but when i try to run it through a cycle, it won't start.


I would replace the key pad it sounds like since everything else works.. so you hit the normal wash and start the dishwasher sits there for a min or two and turns off.. Its not recognising the start button ... Dishwashers

Bosch Dishwasher Cycles will not stop running. They keep starting over. Help please!! Our 2 year old dishwasher will not stop running. It gets to the end of the cycle and starts over again. Plus, the cycles seem to have gotten longer. We called the Bosch repair number and they want $150 in cash to come out and look at it. Then they will come out and fix it!!!! Unbelievable!!!


Carry out a reset.\015\012This should reset the board back to factory settings,\015\012Deep Diver ... Bosch 24 in. SHU5305UC Built-in Dishwasher

Our AEG Favorit 50620 dishwasher won't start. When I push the power button, the power light comes on, but none of the other lights. Pushing the function buttons has no effect. The door is fully closed, and it was working perfectly before. I have tried turning it off and on, unplugging it etc. Nothing works. Interestingly, if you push more than one function button at the same time, some of the function lights come on, but then when you try to start the cycle it still won't work. Help!


... AEG 24 in. Favorit 40650 Free-Standing Dishwasher

My Kenmore Dishwasher 587.1523 won't start. It is getting power, and the lights come on as normal when the Start button is pressed, but the lights turn off after a few seconds.


... Dishwashers

I have a Whirlpool Gu180 ESJQ with a blinking green start light. If I clear this light (hold the start button for 5 second to place it in the end of cycle) then I can get it to start another wash cycle. However, the next wash cycle ends with a blinking start button again and the dishes aren't dry. I had an appliance service man come to check it out and he could not detect any problem! Now I have a leak!


... Whirlpool Gold 24 in. Built-In Dishwasher Dishwasher

Bosch shu8806 Hello, I aquired a shu8806 recently and it doesn't work. It has power and water. I push wash cycle, indicator light comes on, shut door and nothing happens.  So the door switch seemed like a good place to start. Since I am an electrician I thought I would give it a shot. When plugged in, the wire from the motor is 120V but when jumpered to the neutral(common on the door switch), motor doesn't operate. Although, I have heard the motor turn over momentarialy when trying to run unit e


The pump may be clogged, or the motor start capacitor may be bad or some units have a fill switch wired inline with the motor so it won't start unless the unit is full ... Bosch 23 in. SHU 8805 Built-in Dishwasher

My Kenmore Dishwasher 587.1523 won't start. It is getting power, and the lights come on as normal when the Start button is pressed, but the lights turn off after a few seconds.


... Kenmore Dishwashers

Hobart commercial under the counter diswasher LXIC Model Number 130016. DELIME light comes on every day at startup. Machine will immediatly run (in DELIME mode I think) for about 5-10 min and then get E4 error. We unplug power to the unit let it set, replug it back in after 3-4 cycles of this, it will eventually work perfect for the entire day. I have replaced the Sensor that is on bottom front of the unit in the water trough. ( I replace the sensor to the right if you are looking at the un


Q have your run a descaler . to rid the machine of its deposits . in order for the machine to run properly the parts and pump / screens must be clean . / descaling for deliming . dishwasher and icemakers is comm ... Hobart LXIC-6 Dishwasher

I tried the steps listed at this website for the same issue I am having. http://www.fixya.com/support/t273954-kenmore_elite_dishwasher The steps worked to get the dishwasher to "reset" with all the lights coming on. The problem I am having now is that after the "reset" the dishwasher starts to run a small cycle for about 5 minutes. Upon opening the washer, nothing has happened inside (no water, no visible movement of parts, no soap container opening). Upon closing the dishwasher and trying


I think think the water fill is ok and the drain is ok as it uses a seperate drain motor . but what is not working is the main wash motor . so no water is moving and the wash arms are not going around and the lights ... Kenmore 24 in. 17482 / 17484 / 17489 Built-in Dishwasher

All the programme cycle lights come when any programme is selected. I have opened and cleaned the filters, drain pump and non-return valve. I have switched power off at the mains. I have also depressed the off switch for 5 secs as recommended on the Miele website and then re-started the machine. Still get the same error. Any suggestions would be gratefully received.


Hi\015\012\015\012Try and reset the dishwasher by following this sequence---\015\012\015\012Turn the power off to the machine.\015\012Press and hold button 2 and 3 together while turning the dishwasher on. The salt and i ... Dishwashers

Dishwasher I have had above integrated dishwasher which is intermittently tripping the mains fuse. Power is getting to dishwasher and the washing cycles work until a certain point (not the same time) where a loud bang can be heard and the main fuse is tripped. Reset the main fuse and power still gets to the dishwasher and it works again. It has just started to trip the fuse when its not running any cycle (just when power is getting to it). I've checked the fuse on the spur and it looks ok. I hav


Its quite common for the interferance filter to fail on these models its situated in the base of the dishwasher connected to the mains block usually when they fail you can see black dust around it, ... Neff 24 in. S5456 Built-in Dishwasher

After a power outage, that occured while the dishwasher was running, the lights come on and there is a high pitched noise. Then all the lights go off and the motor sounds like it is starting. However there is no water and the heating elemant comes on. The lights on the front; china/crystal, normal wash, clean and heated dry, all come on as if the computer is confused and trying to run them all simultaneously.


Sounds like the board was fried from a power surge ... GE Tritonr XL GSD6260JCC Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.2006 seconds