Having problems with your Electrolux 18 in. ESL4114 Slim-Line Built-in Dishwasher ?

My dishwasher is not draining. About 10cm of water left in bottom and it seems stuck on a cycle?


Answers :

Repair Help & Product Troubleshooting for Electrolux 18 in. ESL4114 Slim-Line Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My dishwasher is not draining. About 10cm of water left in bottom and it seems stuck on a cycle?


... Electrolux 18 in. ESL4114 Slim-Line Built-in Dishwasher

Holding water There is water in the bottom of the machine after the cycle is done. There is definitely draining going on throughout the cycle, but it's not draining completely at the end -and the water that is left is murky. Spoke to a friend who tells me it sounds like the dump valve, but in checking on line, that doesn't seem to be a part that even exists any more. Do I need to buy a new dishwasher? This was not in the budget this year... Thanks for any advice! Nancy


Are the dishes getting clean at the end of the cycle, if not then there could be foreign debris in the pump housing that can cause this, needs to be dismantled and cleaned out, if dishes are clean then the pump impeller will need to be replaced ... Whirlpool 24 in. DU1100XTP Built-in Dishwasher

DISHWASHER WONT GO INTO WASH CYCLES,WHEN I PUSH START GOES CANCEL/DRAIN,CAN HERE PUMP RUNNING THEN IT WILL TURN OFF,THERE IS NO WATER IN THE BOTTOM,SEEMS LIKE STUCK IN DRAIN CYCLE


... Whirlpool GU2300XTS 24 in Builtin Dishwasher

Leaking dishwasher The dishwasher leaks a stream of water at the base -bottom left corner whenever it goes into the final rinse cycle. It does not leak when it is in the wash mode. This leak just seemed to develop suddenly. There was no build up -ie a small stream of water. I just noticed a big puddle on the floor one day after dishwasher had completed its cycle water leak in the left side ,bottom ,husband states a small drip,drip and we do not know what to do or replace. No water standing


I just had this same problem and it was caused by a small plastic seal on the bottom of the door. My friend owns an appliance store and he said this is a common problem for this model of dishwasher. The part was $68 and the labor was $60. I could ... Frigidaire 24 in. PLD2850 Built-in Dishwasher

I have a bosch dishwasher SHE43C06UC22 (non-LED version). It's stuck in the drain cycle and continues to run even when opening the door (it should stop, but it doesn't). As a test, I poured a large glass of water in the bottom of the dishwasher and it drained it into the sink as it should, but it continues to run in the drain mode with no water in it. I've heard I either have a float stuck or an emergency drain switch or leak somewhere causing the dishwasher to continue in the drain mode. Ho


Hello,\015\012\015\012Welcome to FixYa.\015\012\015\012This can be caused by either faulty door switch or indeed the float you mentioned.\015\012\015\012This is where to look for the switch and test it ... Dishwashers

My dishwasher will not drain after cycling. I have check the drain hose connected to the disposal. All is in good order the hose is not cinked and the air hole is unblocked. I have also checked the screen at the bottom of the dishwasher, there is no debris or blockage here either. I can run the dishwasher on normal, it cycles but I still have stagnat water left beneath the bottom rack. How do I check my pump to see if it is working or could it be a short of some kind? It is a Kenmore Quite


The problem is a solenoid under the unit. It is a small black cylinder that operates a valve to change from the wash cycle to the drain cycle. You can probably order a new one from Kenmore for pretty cheap. ... Kenmore 24 in. 15252 / 15254 / 15259 Built-in Dishwasher

My bottom dish washer was draining the water on the top dishwasher and there is always water left over on the top.I remove the pipes and put CLR to clean up drain.Start both dishwasher on rinse cycle ( 12 min cycle) then at 10 min.they start blinking with a No tap (may be water ) sign on it. I run the cycle again now a F1 sign coming with a tool sign.And both dishwasher going crazy ,it turn on by itself even I powered them off.


Hi\015\012\015\012\015\012Thanks for using FixYa. F1\015\012error means that the flood switch has been activated. You'll need to reset it by poweri ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

Dish washer does not drain after the cycle is complete. The last few months when the dishwasher is done their would be a small amount of water left in the bottom. It didnt create any problems but would smell after a few days. So we would just run the drain cycle and it would empty. Well i got home to and the wife said the it was really full. The water was dirty and when you run the drain cycle it didnt drain. She said the dishes were clean. So i cleaned the vent, and filled the sink with


Check drain hose and drain pump.End of drain hose must be in same level with machine.Try it. ... KitchenAid KUDR01TJ Dishwasher

My 5 year old bosch dishwasher cycles to one minute and then cycles forever and ever with very soapy water in the bottom. After a very long time, the water is out of the dishwasher but soap residue is left on the dishes and the bottom ot the dishwasher.We are presently using only 1/2 teaspoon of detergent (Finish brand). I have had a repairman here to look at it, but he didn't seem confident that it was a timer issue and even though I have paid the exorbitant service call fee, I am not sure I wa


Hello,Welcome to FixYa.Based on your description ... Bosch 24 in. SHU66C05 Stainless Steel Built-in Dishwasher

Dishwasher leaking Our dishwasher all of a sudden started leaking. I've taken the front panel off the door and can see exactly where. It's not a hole or anything...it's at the front, left edge of the basin, the bottom left corner at the front. It seems that right after it fills with water, it starts to leak once water is moving around inside and washing cycle starts. It is as if big waves are being pushed to the front left corner and over the lip of the basin. I don't think the water level is to


Just an idea...if i'm understanding you correctly,could the door seal be creased there or folded over by use and age to permit this to happen? cause you said nothing is missing ... Whirlpool Gold 24 in. Built-In Dishwasher Dishwasher

Shu9925uc/14 bosch dishwasher leaves standing water in the bottom of the pump. The pump seems to be bad because it wont drain out the back hose. I have run the diswasher full cycle and put the drain hose into the sink to test. It wont drain at all now and I dont hear the pump. Perhaps unrelated: Pump seemed to stop working after the back hose disconnected itself from the back of the unit spilling water all over the floor. When I reconnected the unit to the wall the pump now seems to be disfunct


Hi Dishwasher not draining issue occurs due to kinked drain pipe, clogged drain filter or drain pump. Check the drain hose for any visible clogging, remove if present. If no visible lint is present then remove then turn off the dish ... Bosch SHU9925UC Built-in Dishwasher

My Frigidaire Dishwasher FDB1050RES2 gets stuck in a rinse cycle. The light on the front will be lit "clean" but the bottom of the washer is full of water. Opening the door does not turn off the "clean" light. For me to get it to run, I have to unplug it, plug it back in, push the start button until the ?washing? light comes on. I then push the start button once more and the dishwasher will begin to drain. I open the door as soon as I hear the water stop draining into the sink drain. This


By the descrition you are giving you will need to replace the main control board.Part number 154568401.you may also need to check the float switch.The part will run about 110.00 dollars from a local parts store ... Frigidaire 24 in. FDB1050RE Built-in Dishwasher

The dishwasher was not draining, I tried the baking soda & vinegar trick and it seemed to release the clog..now, it seems no water is being supplied to the machine during a wash cycle...it drains fine, no water and the rotating arms for the sprayer on the bottom of the tub don't seem to be moving..any help??


... Magic Chef 24 in. DU6550 Built-in Dishwasher

I have a whirlpool gold model GU1500 diswasher. When the rinse cycle ends the water pumps out into the garbage disposal like it should, but then water backs-up from somewhere into the bottom of the dishwasher. The overfill protection drain seems OK...the water doesn't overflow. It doesn't have a air gap on the sink. The drain hose goes directly from the dishwasher to the inlet on the garbage disposal. It appears to be properly installed per the installation instructions. The washer is about 4 ye


Seems you answered your own question here. You need to make an air gap in the drain hose - take as much slack as possible and make a curve (upside down U) under you sink as high as you can go. Make sure you clip ot to back of the cabinet to stabili ... Whirlpool 24 in. GU1500XTLS Stainless Steel Built-in Dishwasher

Bosch compact Logixx dishwasher (8401) will not start after it did turn on to start a cycle. Pump made laboured draining noises then seemed to cut out. Water remains in the bottom after last cycle.


... Bosch Dishwashers

Dishwasher The dishwasher detergent door opens during cycle but powdered soap remains in tray. At end of cycle glasses and dishes are wet. a little water is left undrained at bottom. This is a Frigidaire model FDB510LCS1. Checked upper and lower spray arms and they seem ok and pump seems to be working


I have seen this problem before on a couple of dishwashers.\015\012\015\012How are the dishes doing? Are they coming out clean, or do some of them "fail". \015\012\015\012If you rinse the dishes before putting them in the di ... Dishwashers

Bosch Dishwasher model : SHV4313GB/17 The machine won't switch off and the pump is still trying to drain water ( there is no water left in machine ) The cycle seems to have finished as it has made the beep sound as if it has finished. The dishwasher is still working even when you open the main door. Have tried to reset it but to no avail. Even after turning it off at the mains it still starts up again as if in mid cycle ! HELP PLEASE


I have a SHV. My sink drain backed up, and the water accumulating in the sink then migrated to the dishwasher, through the drain pipe, causing the dishwasher to fill up and, it turned out, overflow a little. When I turned on the dishwasher, the wat ... Dishwashers

When washing dishes, the washer drains okay at the end of the cycle. However, ir seems that for some reason in the mornings we are finding water in the bottom of the dishwasher--sometimes so much that some has leaked out to the floor. When the drain cycle is turned on, the water goes out okay? Any advice?


Sounds like a bad fill valve. ... Kenmore Dishwashers

Water will not drain out of the tub all the way and behind the front door bottom in the insulation seems to be wet. and the cycle seems to take a long time to run...thanks Dishwasher Model No. SHU9922UC/U12 goes through cycle properly but fails to drain completely.


Water does not drain from the dishwasher \015\012\015\012Check sink drain and ... Dishwashers

Subj: ge dishwasher mod/gsd3960looss - 1yr 4 mos old. problem: will not drain only used 6 times. last use after cycle done, water remained. had to hand drain. removed cover and checked drain area, no debris found. drain tube is connected to disposal by clear plastic tube; no clog in tube. the sink drains are clear and the disposal works normal. dishwasher drain seems to be stuck in closed position. this model has the touch pad controls. any solution????


... GE Dishwashers

Kenmore Dishwasher My dishwasher fills with water and then stops. I hear the cycle timer continue all the way through the cycle. I pulled the screen off the bottom inside of the dishwaher and stuck my hand in the diswasher drain. Originally I felt and cleared what appeared to be a torn up rubber band. I feel a thin straight metal pin that I can rotate and I believe it causes the pump to rotate as well. Once I do that the dishwasher will run normally thorough a complete cycle...BUT I have to


If you have either dry bearings in the motor or sticky grease buildup in the pump bearing/seal, it can cause the motor to stick rather than rotate on startup. More likely to be greasy crud buildup. \015\012\015\012The best you can do without disasse ... Kenmore 24 in. 15149 Built-in Dishwasher

Our dishwasher won't drain completely. I ran it through a regular cycle but it was left with water in the bottom.


Have you tried canceling the cycle? To cancel, turn the on/off switch to on, then press and hold for three seconds the two buttons labeled "Cancel Drain". Keep the door closed for the next minute so that the dishwasher can complete the cycle ... Bosch 24 in. SHE44C02UC / SHE44C06UC / SHE44C07UC Built-in Dishwasher

We have an Asko 1385 dishwasher. It drains via the same drain into which our kitchen sinks drain. We had a blockage there. When that was fixed we noticed that the dishwasher does not drain properly and does not fill at all yet it seems to go through its cycle. I am wondering if a float switch or some such is stuck but I cannot find one in the bottom of the tub!


It is a plastic circular float in the bottom of the tub.With an exact model # we can point you in the right direction.Thanks!! ... Asko 1385 Dishwasher

Jenn-air dishwasher JDB-5 (jdb1105awb) will not drain. Have repeatedly prompted drain cycle (start/cancel twice) there is what seems to be a pump noise for a minute or two, but no water flow noise and water level is the same in the bottom. The manual is sparce on trouble shooting and schematics. I suspect something is clogging the drain path. No changes to the drain hose routing. Machine has been installed for three years with no major issues. What is the recommended disassembly sequen


... Jenn-Air JDB6510 Built-in Dishwasher

I have a ADG450 about 7 years old, the problem is there is dirty water left at the bottom of the dishwasher after finishing the cycle and the dishes look as if they have had the final rinse in the dirty water. also i have tried the rinse cycle with no dishes and all the rinse water had not drained away. I have cleaned the iside of the washer and where the water goes to the pump. Any ideas


Check the pipe leading from the dishwasher to the outlet, maybe under sink. this needs to be raise up as water will flow back into washer. Had this problem myself, felt foolish when the repair man just tied it up and left. ! ... Whirlpool ADG450 Slim-Line Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.2720 seconds