Having problems with your Electrolux 23 in. ESI602 Free-standing Dishwasher ?

Dish Washer, Electrolux Home Products, Model FDB2510LCC0, Serial NO: 7H34962223 Machine does not drain or add water. The machine has been worked for a couple of years. I checked the following: 1. Overfill Protector not stuck 2. Motor turns on and the machine cycles correctly 3. Since the machine has been running correctly the unit is hooked up correctly: hoses, garbage disposal, knockout plug. Again everything has worked and the motor does cycle and the machine will perform the different cycles


Answers :

Repair Help & Product Troubleshooting for Electrolux 23 in. ESI602 Free-standing Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Dish Washer, Electrolux Home Products, Model FDB2510LCC0, Serial NO: 7H34962223 Machine does not drain or add water. The machine has been worked for a couple of years. I checked the following: 1. Overfill Protector not stuck 2. Motor turns on and the machine cycles correctly 3. Since the machine has been running correctly the unit is hooked up correctly: hoses, garbage disposal, knockout plug. Again everything has worked and the motor does cycle and the machine will perform the different cycles


... Electrolux 23 in. ESI602 Free-standing Dishwasher

I have an older Maytag model #WU482. For some reason it will not drain and will only run using the economy mode. I can hear the timer ticking at all other cycles and it does click between cycles. I recently replaced the drain float and the machine had been working fine after. The motor is working and the belt is good. I think the kids were playing with the timer knob. Could this cause a problem with the timer motor? Or does this sound more like a pump out issue, impeller? I'm thinking its


First,inspect the drain float. Make sure it rides on the micro switch correctly or it will not take on water.Check the float micro switch for continuity. Check for power at the water valve when it calls for water. Remove the wire harness from the tim ... Maytag 24 in. PDB1420 Built-in Dishwasher

Problem with ASKO 1385 dishwasher. Unit has manual cycle knob, not electronic. Clock/timer seems to work normally but no water is pumped in and a motor runs continually throughout cycle, even during drying time. Motor continues to run continuously after end of cycle.


CHECK THAT THE WATER IS ON TO THE UNIT, AND IF VOLTAGE IS AT WATER INLET VALVE. IF VOLTAGE THEN WATER SHOULD BE COMING IN EITHER BAD INLET VALVE OF CLOGGED SCREEN IF THERE IS VOLTAGE TO VALVE. NO VOLTAGE THEN CONNECTIONS OR TIMER WOULD BE NEXT. ... Asko 1385 Dishwasher

My dishwasher SMS 448 works up to the point in the cycle when the dispenser is supposed to dislodge the Powerball detergent. It doesn't, and the machine stops. If I open the door and click the dispenser, the Powerball falls into the dishwasher unit itself. But when I close the door, the machine doesn't operate until I turn the knob a bit farther on in the cycle. Then, no water comes out, but the knob moves on in the cycle and the heating pipes heat up


... Bosch Dishwashers

Dear sir In an attempt to dislodge a blockage of my sewer line using Draino and a plunger some of the Drano ended up in the dishwasher and now the dishwasher will not run. My dishwasher is a SHU3036UC/U12. When starting the unit up it empties the unit but the cycle newer ends, in other words the timer does not advance to the next cycle, I have determined that the timer motor works by removing it from the unit and supplying it with power. One thought is, can the water level switch be stuck in


HiCheck this video and clean the drain pump assembly: ... Bosch SHU3036UC Dishwasher

Bosch sgs43eo2gb dishwasher. wash programme completes, water drains out, but machine goes on draining, forever, stuck at around 50 minutes on the facia clock. there is no leak on the machine and everything else has been cleaned and operates perfectly. ie,fills correctly,heats correctly and drains fully but won"t stop draining & refill. Cancel programme and reset and it works perfectly until end of wash cycle again, when it continues to drain even with the door open. There is no leak in the machi


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks for\015\012using FixYa. Please once again check that the hoses are not kinked or drain pump and filter ... Bosch 24 in. SGS43C12 Classixx Free-Standing Dishwasher

I have a maytag washer (model -dependable care) and when we start the wash the motor just hums, the water does not fill, if we move the timer switch to rinse the motor engages and the unit works entire the end of the cycle, this is the same for all cycles


Check your fill tubes remove the hoses and see if the filters are plugged, you are not hearing the motor humming. You are hearing the watervalve humming, the motor will not start until the tube is full of water. ... Maytag MDB6650A Built-in Dishwasher

Bosch Shu43C02UC dishwasher fills with water but the washing won't start. As the filling nears complete, a double clicking noise occurs to start the washing motor but nothing happens. The time continues to countdown but the machine is silent. When I open and close the door, the click click noise is heard but the machine is silent. I can cancel the cycle and drain the water but none of the washing or rinse cycles will activate but the timer works. The soap door even opens if the timer is left to


Have you checked the inlet water temperature is at the correct level for the dishwasher.\015\012\015\012Please provide the full model no. of your dishwasher -- Shu43C02UC /??\015\012\015\012I think the problem is linked to th ... Bosch 24 in. SHU43 Built-in Dishwasher

I have a fisher & Pakel dishwasher and it appears to have brown a fuse inside the machine which means it does not work at all and the problem occurred during the wash cycle. This means the seal (which is a top piece that's lifted and lowered by two motors. When the seal is in the lowered position it creates a complete seal but it also locks the drawer (single drawer dishwasher) so it cannot be pulled out. I repaired the dishwasher two years ago. One of the lifter motors didn't work. I replaced t


According to the service manual there is no problem in manually forcing open the drawer in the situation where the power has failed part way through the diswasher cycle.\015\012\015\012The problem is that once you force the lid open, you ... Fisher and Paykel Dishwashers

Bosch shu8806 Hello, I aquired a shu8806 recently and it doesn't work. It has power and water. I push wash cycle, indicator light comes on, shut door and nothing happens.  So the door switch seemed like a good place to start. Since I am an electrician I thought I would give it a shot. When plugged in, the wire from the motor is 120V but when jumpered to the neutral(common on the door switch), motor doesn't operate. Although, I have heard the motor turn over momentarialy when trying to run unit e


The pump may be clogged, or the motor start capacitor may be bad or some units have a fill switch wired inline with the motor so it won't start unless the unit is full ... Bosch 23 in. SHU 8805 Built-in Dishwasher

I have a hotpoint aquarius DF22, problem: machine not taking in water to commence the cycle, (this is intermittent and worked sometimes) the plumbing has been checked regularly and for a time would start after reconnection, the motor is fine the electrics have been checked by a qualified electrican who cannont source the problem, now the machine will not take in water at all, any suggestions please?


... Dishwashers

Half way through the wash cycle the motor seamed to still be working but no water was going through after i open the door mid cycle now i can start the machine but all the sounds are there but no water


U probably have a bad water valve under the dishwasher that is not opening properly if u have hard water that's probably what it is,it has lime scale in or on the valve ... Bosch Dishwashers

Normal wash cycle- tub fills (?), then comes a loud hummmm and nothing happens. I noticed water level didn't reach heater coil and added water until limiter switch clicked. Still just a loud hummmm. Machine was well into its regular cycle when this first occurred, but now, won't even get past initial fill. Pushing the "Cancel/drain" button activates motor and pump: they work fine.


You are an expert enough reading this. But with a terrible complicated dishwasher. First clear the waterlevel problem.\015\012Rest is a result. You do not need me, join us. Next time buy something more plain. ... Dishwashers

Ice maker cannot eject cubes. I took off the front cover and found several contact points for checking the motor, water valve, thermostat, mold heater. There is also a line voltage and neutral contact. Are these contacts live only during certain parts of the cycle? I suspect the heater isnt working to loosen the cubes so they cant be ejected. The motor sounds lilke its running but the ejector is not moving nor is the Gear on the front of the unit. Can someone give me a full description of this t


I usually replace icemakers as a unit. It sounds like the mold heater is out. The system cycles like this: Fill, freeze, mold heat, eject, and start over. The mold heater not working will prevent ejection. ... Kenmore 24 in. 17482 / 17484 / 17489 Built-in Dishwasher

Bosch SMS4012GB dishwasher. Refused to fill. Found tray full of water in base of unit. Mopped up water about 2 litres. Machine works but lower reservoir on the side of the machine with float switch overfills and overflow leaks about an eggcup full each cycle. What is causing the overflow please?


An electric switch activated by air pressure. This device detects air pressure exerted on it through a flexible tube connecting it to part of a water tub. \015\012When activated, this switch then opens an e ... Dishwashers

My Siemens SL84A305UC/21 dishwasher will not drain. I've checked the drain and it is clear. I can hear the motor hum during the drain cycle. It will fill and wash OK, but not drain. Does this machine have a solenoid for draining and if so how do I check it? How do I check the pump to ensure it is functioning correctly? I've tried to remove the plastic bottom of the machine to see what is inside and to troubleshoot the components, but it seems almost impossible to remove. What is the trick? What


... Siemens 24 in. SL84A305UC Built-in Dishwasher

Dishwasher Water is not going through upper and lower spray arms. Checked overfill protector switch, inlet valve, inlet valve screen, pump blades move freely, Pumb motor is working , Water enters into machine but does not go throught spray arms. Water heats up, Machine will go through all cycles but without water going through spray arms. 650 / 690 series gldb656jso


... Dishwashers

My Siemens SL84A305UC/26 dishwasher will not drain. I've checked the drain and it is clear. I can hear the motor hum during the drain cycle. It will fill and wash OK, but not drain. Does this machine have a solenoid for draining and if so how do I check it? How do I check the pump to ensure it is functioning correctly? I've tried to remove the plastic bottom of the machine to see what is inside and to troubleshoot the components, but it seems almost impossible to remove. What is the trick? What


... Siemens 24 in. SL84A305UC Built-in Dishwasher

Looking for info on our churches dishwasher - Toledo Kitchen Machines. Model # TDA27. I can describe it as a single cycle dishwasher. Wondering what type of detergent to use and if there is a manual available. There is a small seal leak between the motor and the pump, other than that everything works. ( this has not been used in 10+ years).I am now in charge of bldg maintenance and am trying to get everything in working order. Any help is appreciated. I am guessing the circa is mid to late 60's


Dishwasher Repair Guide: How To Fix a Dishwasher - ACME HOW TO.com\015\012\015\012\015\012\015\012 ... Dishwashers

Hobart commercial under the counter diswasher LXIC Model Number 130016. DELIME light comes on every day at startup. Machine will immediatly run (in DELIME mode I think) for about 5-10 min and then get E4 error. We unplug power to the unit let it set, replug it back in after 3-4 cycles of this, it will eventually work perfect for the entire day. I have replaced the Sensor that is on bottom front of the unit in the water trough. ( I replace the sensor to the right if you are looking at the un


Q have your run a descaler . to rid the machine of its deposits . in order for the machine to run properly the parts and pump / screens must be clean . / descaling for deliming . dishwasher and icemakers is comm ... Hobart LXIC-6 Dishwasher

I have a BAUMATIC BDW8 which has started beeping when you close the door to start the cycle. You can hear a motor running but no water is being pumped in. When you re open the door half the lights are flashing. This is an intermittent fault, the machine will still work ok on occasion.


Thanks for your question!I'm sorry that you haven't received an answer yet.The response rate on FixYa FREE questions is usually over 80%, but sometimes questions go un-answered when:1. the question is unclear, incomplete ... Baumatic 23 in. BDW8 Built-in Dishwasher

Noticed dishes on top shelf not entirely clean. Ran machine empty and opened many times during wash. Noticed that Lower Spray Arm works as expected, but Middle Spray Arm turns only 1/8 or less, then Lower Arm spins again. Schematic with Use and Care manual just says pump motor switches from one to the other in certain cycles, but I don't see this happening. Looked for obstructions to water flow and pressure seems normal. Is control for this function part of the pump, or in the control panel?


Something could be in that checkball, see page 5 ... Frigidaire 24 in. GLDB653A Built-in Dishwasher

I have a whirlpool du1055xtsq3 dishwasher that is partially working. Cycle buttons light up but start button does not. I've tried resetting by pushing sani-rinse and heated dry alternately. Control panel lit up and heard motor running but no water. Your help is appreciated. Unit only 2yrs old. Thanks!


... Whirlpool Dishwashers

Normal cycle light blinking, won't turn on MDB7609AWW1. Was told it was micro computer. Replaced it....same problem..Put old micro computer back in.. wife secured all wires and banged the machine and it started working tfor a few Days.. stopped with same old symptoms..I'm sure guru is correct and it is the touchpad, but his facing appears to be glued on,I don't wan't to ruin the front of the console , and I've not been able to find a touchpad part on the schematic or online. Help???


... Maytag MDB7609AW Builtin Dishwasher

Frigidair model FDB520rHB2 Bought this brand new dishwasher and had it professionally installed. The unit seems to cycle fine, but after it's done, there is always a pile of detergent on the machine floor from where it dropped out of the dispenser. Plus the dishes are somewhat clean, but not all the way. I've tried all the trouble shooting that I could come across, but nothing seems to work. We have tried liquid, tablet and powder detergent with all the same results. Any ideas? Thanks


... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1084 seconds