Having problems with your Electrolux Dishwashers ?

I'm replacing the detergent dispenser in a dishlex global 300 have a ELTEK 100418 DISPENSER to replace the existing does it suit and also which pin is the 240 volt and which is the 50 Hz


Answers :

Repair Help & Product Troubleshooting for Electrolux Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I'm replacing the detergent dispenser in a dishlex global 300 have a ELTEK 100418 DISPENSER to replace the existing does it suit and also which pin is the 240 volt and which is the 50 Hz


... Electrolux Dishwashers

After a power surge the dishwasher does not work at all. It just beeps constantly. There are no lights on the touch pad at all. The only thing that stops it from beeping is to remove the 2 pin black and white wires. I replaced the control module. Nothing changes. Do I need to replace the touch pad? What about the 3 digit clock? These parts together cost 145 dollars. I do not want to buy these parts and put them in to find out that did not fix the issue. I also unplugged the


... GE 24 in. Profile PDW9880JSS Built-in Dishwasher

ARISTON LSI 45/50 UK ALL COLD CYCLES ARE PERFECT ON HOT CYCLES IT GOES THROUGH ALL THE STAGES BUT NEVER ENDS THE CYCLES AND ALSO I THINK THE ELEMENT TEMPERATURE IS NOT BEING SENSED TO ALLOW HOT WASHES TO CONTINUE AND FINISH I ALREADY REPAIRED THE INITIAL FAULT WHICH WAS A RED 2 PIN CONNECTOR WITH A WHITE SOCKET GOING IN TO IT BOTH WITH 2 RED WIRES ON WHICH WAS VERY BADLY BURNED / CORRODED I REPLACED THIS WITH A 15 AMP CONNECTOR BLOCK BUT NOW I HAVE THE HOT WATER CYCLE FAULT


I tried to look up your model dishwasher ( aristion lsi 24/50uk ) by whirplool / can not find in data base / also you stated that all cold cycles work/ most d/w only use hot and there is no cold cycles . so there is always time to ... Whirlpool Gold 24 in. Built-In Dishwasher Dishwasher

I am replacing a frigidaire dishwasher washmotor. Everyone and videos tell me how to replace the motor. In the instructions in the box they say replace the sump bottom also. Why would i have to replace the sump also and not just the new motor?


Hello, chris\012 \012 I was trying to help\012 you out here. I was going back to some customers that asked questions \012in the past and it appeared that no one answered them, so I thought I \012would take some ... Amana ADB1400AWB Dishwashers

I have a kudso1flss6 dishwasher with the clean light flashing 7 times. Can I replace just the control unit or do I have to replace the heating element also? I also need to know how to replace the part or parts. Help!


Depress cancel button. Turn off power WHILE STILLL HOLDING DOWN cancel button, turn power back on. Viola! ... KitchenAid 24 in. KUDI01FLSS Stainless Steel Built-in Dishwasher

I have a Kenmore Dishwasher Model #665.168790000 and the water fills just fine and empties fine when cancelling cycle but when pressing any wash cycle the pump/motor just makes a loud humming noise and does nothing. I took apoart the lower assemblies to clean everything out but the problem hasn't gone away. Do I need to replace the motor or the whole motor assembly (also contains impeller kit)??? Also, I don't think I need to replace the whole sump & motor assembly do I???


... Kenmore Dishwashers

The lower shelf/drawer in the dishwasher has rusting pieces mostly at joins and also has upright pieces breaking off. Also a couple of small pieces have broken off the top shelf/drawer. I need to replace both shelves/drawers. how do i order replacement parts and at what cost. pat


Hi,\015\012\015\012you'd have to start by providing a make and model & serial number. Check out repairclinic.com, amresupply.com or searspartsdirect.com to name a few, but there are many more on-line appliance part vendors if you do a search with you ... Asko D1876 Dishwasher

I have a Dishlex Global 450 dishwasher and have a faulty seal to replace. The original door seal had a foot on each side and the replacement I received has 45 degree cuts and no foot. Also the bottom seal replacement appears to be a screw-in type where the original was slipped behind a fold in the door. I have been assured by the supplier that I have received the correct replacement parts. Could you confirm the these parts are in fact correct and if they are which way should the seal lip an


Hello Tony. I am as concerned as you are that this is not the correct replacement part. The key to getting the right part is the model number which is on your machine, if you know where to look. Do this, go to this link to properly locate your mod ... Dishwashers

Dishwasher racks are falling apart from rust. I would like to replace them, but am confused as to what parts to buy. Also, do you know where to buy them? When I searched for replacements, it seems like by the time I finish buying all the replacement parts, I should just replace the entire dishwasher!


The racks are like 200 dollars a piece,replace the dish washer. ... Dishwashers

Dishwasher 66513752K601 keeps blowing the thermal fuse. (Bi-Metal W10258275). I have replace the Thermal fuse several times. After i replace the fuse for some reason after a few months or less it will blow it out again. I have also replace the front panel assembly after it stopped working correctly. I would like to know how to test the dishwasher to find out the root cause of the fuse issue. I don't want to be replacing the fuse every time and don't have the $$ to buy a new dishwasher. Everythin


... Dishwashers

I have no heat my hot water coming in is as warm as it gets and on dry it will not heat up. Is there a fuse or circut breaker for the element or do I need to replace it. Also if I could ask how hard is it to replace. Thank You Very Much Dino


Just call me on +263912639492, thta's easy.thank you.\012\012Dr. Kelson ... LG 24 in. LDF 7811 Stainless Steel Built-in Dishwasher

Whirlpool - Quit Partner I - DU1048XTP: Start at the beginning - Dishwasher would go through most of it's wash cycle and stop and the 'Start/Resume' LED would start flashing. Would press 'Start/Resume' and wash cycle would start again and run non-stop. Would have to hit 'Cancel/Drain' to stop. Called local service tech and he said board would need to be replaced. First board he brought failed right away, second board was installed. Tech also replaced latch handle assembly because it was missing


Have you asked the technician if the water temperature is OK.\015\012\015\012Run it again and after 30 minutes cancel and see if water temperature is warm or not. If not warm enough, then likely causes are heater is faulty or if you are u ... Whirlpool Dishwashers

I got this dishwasher from a friend that had mice chew the hoses and i was told that it worked perfect before the mice chewed it. I replaced the drain and fill hoses plus the power cord. when i put everything back together and power on I get F1 on the top drawer and the rotor rotates and the heater plate turns on. The botton drawer does nothing with no display. I checked all the wires with a meter and found good continuity thru every pin. I replaced the main filter board. I even switched the


Did the F1 error in the top drawer disappear after you replaced the mains filter board? ... Fisher and Paykel 24 in. DD603H W Built-in Dishwasher

My dishwasher is leaking from front bottom left side when on. have checked the door seal and it is worn about 3" up on left. there is also a rubber seal on the door itself running along the bottom. can this also be replaced and if so where can i get one?


Hi,\015\012Yes, they can both be replaced...this tip will also tell you how to purchase them...\015\012\015\012Here is a tip that I wrote about dishwashers and them leaking. ... Indesit 24 in. IDL500 Built-In Dishwasher

My KitchenAid KUDS01FLSS0 won't turn on when the "Start" button is pushed. Several months ago it began requiring multiple pushes to get it to start. All the cycle lights on the control panel work when pushed - except the "Start" button. Online & repair parts person suggested I replace the: - Tail Cable Ribbon; did not fix problem, then - - Electronic Control Board (interface) which also did not fix it. Should I replace the Electronic Control Board that is actually the part with the buttons


... KitchenAid Dishwashers

Dishwasher starts and runs to 2nd rinse cycle, when pump starts to pump water out, all lights on front display flash along with key pab lights blinking. you can turn off and restart, but is does the same. Diswasher will also try to start when in off mode. Replaced circuit board and it does to same. Did I get a bad circuit board or is there another problem. Also when I try water service test, I get a Rinse aid fault.


U REPLACED THE CIRCUIT BOARD IN THE DOOR, THE ONE BEHIND THE CONTROL BUTTONS? THAT IS THE TIMER, IT IS KNOWN AS THE CCU OR CENTRAL CONTROL UNIT, THAT IS WHAT CONTROLS ALL TIMED FUNCTIONS, SO THAT REALLY IS THE ONLY PART THAT CAN CAUSE THIS PROBLEM ... Frigidaire 24 in. FDB1050REC Stainless Steel Built-in Dishwasher

No sanitizer Hi, I've got a 501HT that's acting up, it is not taking up any sanitizer, is it the pump or could the line be clogged? Also, I've noticed the detergent line has never been installed, isn't there a pump for that aswell and shouldn't that be operational. The previous owner never mentioned it? Lastly, I had a service guy out this spring to do some repairs and told me that one of the coils on the booster tank was shot and should be replaced. Should I replace all of the coils or just the


Hello\015\012If you have a 501HT you shouldn't need a sanitizer because the machine sanitizes using hot water. The final rinse temperature should reach 82 C to kill all germs. The chemical pump's element tubes may be worn out. This would preven ... Moyer Diebel 24 in. 501HT Built-in Dishwasher

We replaced our flooring a few years back with ceramic flooring which our floor approx. 3/4 inch. We now want to replace our dishwasher but find that the opening is now 335/8 and the standard height of a dishwasher is 34 inches . We also have a granite countertop. The tile floor does not extend underneath the current dishwasher. how can we install the new dishwasher???


Hi,Rather than Going for Different Adjustments,you could Buy a Dishwasher with Small Height. Bosch have so many Dishwasher's that could Actually Fit within those Dimensions without any problem.Even Hotpoint and Hoover have Mod ... Dishwashers

We have a Maytag dishwasher, MDC4000AWX. Both dish racks are rusted, broken and falling apart in places. How much is it for replacements of these dish racks. Also, so you have any used dish racks in excellent condition. We do not want to replace the dishwasher because it works perfectly. We are just VERY disappointed this this rust problem. What can we do?


The only way to get new racks is to buy them here at link below. Parts #1 and #3\015\012\015\012 ... Dishwashers

The waste pipe on my hotpoint dishwasher is connected to a spigot. I now want to buy a Bosch replacement but all models have a waste pipe which is too small in diameter to fit the existing spigot. A smaller spigot does not seem to exist and there is no room to install a stand pipe. Can you suggest a solution? Thanks


Do you have a garbage disposal? It is usually easier to drain through the garbage disposal. There is a fitting for this on all disposals. Be sure to remove the knock out plug first. ... Dishwashers

We have a Haier dishwasher and the capacitor burned out. The mahcines are sold at Argos and Comet but I can't source a replacment part which seems kind of crazy. It is out of Warranty and comet can't help. The capacitor is 5uv and has 2 pins. There are generic alternatives with 4 pins. Comets spare part place doesn't sell the capacitors separately and don't know if they come as part of a wider unit. Can anyone help I understand these parts cost about £6 and don't want the expense of a new


... Haier Dishwashers

Plastic Pieces We purchased our ASKO 1385 dishwasher 7-8 years ago. Over the years, I have found "small square, thin, pieces of gray plastic" inside. Where are these coming from? Also, we have replaced the drain pump 2 years ago and looks like we'll be replaced the main pump within the next few days as no water is going through. We are looking at paying big $$$ for that pump. Almost half as much as purchasing a new dishwasher. Is this a common problem?


Yes, I have the same problem and it is the upper bearing rack, not the pump impeller. The new bearing kit is $30.00 (another is available for $123.00-the same!!). ... Asko 1385 Dishwasher

My dishwasher makes a banging sound, I've checked the arm & even when the washers is empty it still makes that sound. NOW I've ALSO got a sound like a "clothes washer in spin cycle mode" also in the wash mode of my dishwasher. Do I need a service call or should I just replace it since it seems to be falling apart....it's only 2 yrs with min use


Hi,This is quite a common problem. I would be able to help you, if you could provide few more details. When did you hear the banging noise i.e when filling, start of the cycle, mid cycle or it is always there?Thanks!! ... GE 24 in. Profile PDW7800 Built-in Dishwasher

My SHE43 Bosch DW will not pump the water out after the last cycle. The service guy said the Door latch was broken and replaced it. but the problem still exist. He now say that the water lines are freezing up because the DW is on an outside wall. The Thermador DW that was replaced never had this problem during the 15 years it was located in the same place. Could this be a bad design? Help!!!


I\015\012\015\012\015\012\015\012 the water doesn't drain from your dishwasher, check these:Drain line/air gap ... Bosch 24 in. SHU66C02 / SHU66C06 Built-in Dishwasher

It doesn't work at all no lights anywhere. I ordered and replaced new switches, and replaced the control board. The circuit breaker is on, and if I put one of the little meters that just tells if you have either 120 or 220 volts accross the two white wired connections on the board, 110 lights up. The float seeks to move freely.


If you have no lights at all and you have power to the circuit double check that the circuit board is connected properly first since you replaced that. On some models there is a safety circuit installed that disconnects power in the event it detects ... Kenmore 24 in. 15932 Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0888 seconds