Having problems with your Electrolux Dishwashers ?

Dishlex global 310 - I've cleaned all filter components and removable parts but still it's like no high pressure water is getting through. How do I check to unblock the inflow at the bottom of the unit?


Answers :

When the Dishlex starts for the first time, there is a\015\012service mode set up. The service mode allows you to set a 'fill-time'\015\012for the water to reach the right level, depending on the water pressure\015\012and flow... So resetting the Dishlex\015\012is the first step. set the water level. If the water is too low,\015\012it will not rush, it will flash. When the water is too high, it will\015\012leak out of the rubber seal.Check that the inlet filter was not blocked and that the tap was turned fully on.\015\012Disconnected the power lead, inlet hose and drain hose and remov the\015\012dishwasher. Remov the bottom metal cover and check ther plastic\015\012box if full of sludge. Un clipp it and the flexible hose attached to it. Clean out the sludge and reassemble. disconnect the dishwasher - check for blockages in the input hose filter - remove the bottom of the dishwasher (two screws at the front) - look for the translucent plastic bucket thing attached to the side of the main assembly - unclip it from the main assembly and remove the white hose attached to it - flushe the gunk down the sink (you need a small brush or piece of wire to get it out.hope this will help
Repair Help & Product Troubleshooting for Electrolux Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Dishlex global 310 - I've cleaned all filter components and removable parts but still it's like no high pressure water is getting through. How do I check to unblock the inflow at the bottom of the unit?


When the Dishlex starts for the first time, there is a\015\012service mode set up. The service mode allows you to set a 'fill-time'\015\012for the water to reach the right level, depending on the water pressure\015\012and flow... So resetting the ... Electrolux Dishwashers

Ge profile dishwasher not draining Model no. pdw9280n20ss I checked the drain line at the garbage disposal. No blockage. Line is clear. The back flow loop is high and not kinked. Only a small trickle of water comes out of the disposal drain at the end of cycle. No forceful pressure of water like before. I removed the smaller grill drain area and cannot feel any objects down in there. I do not know how to remove the larger fine mesh grill on bottom. Any suggestions?


Did you ever figure out how to remove that large mesh bit? I am stuck at the same spot and would love a hint. ... GE 24 in. Profile PDW9880JSS Built-in Dishwasher

I have a KARCHER Model K 2401 which onstart up has normal water pressure rather than the high. I can usually get it to work by removing the tip, pressing the trigger and running some water through without the tip on. The i replace tip and it will usually retain the high pressure. If I stop depressing the trigger I have to go through these same steps. It is like it loses prime. It works well once I get it started putting out the high pressure.


... Karcher 2500 PSI Pressure Washer

I have a model PW 2200 gas pressure washer. It suddenly lost it's high pressure the other day after working fine for @10 minutes. It's getting plenty of water, but the engine doesn't seem to rev up to give it the high pressure. The operating instructions say to check the oil in the engine, and the PUMP before starting, but I haven't found any place to check for an oil level in the pump????Any ideas, I'm very confused.


... Pressure Washers

Hi have a Karcher 6.91 and I cant get any high water pressure. It has power, I have checked the o-rings, filter and lances but it does not build up high pressure. The water also appears to flow back


... Karcher Pressure Washers

Hi have a Karcher 6.91 and I cant get any high water pressure. It has power, I have checked the o-rings, filter and lances but it does not build up high pressure. The water also appears to flow back


... Pressure Washers

Hi ..I have an Excell gas pressure washer model no. Exwgv2121-3 with Faip 2100 psi 2 gpm vertical shaft pump..the problem is that there is water leaking from every weep hole at the bottom of the pump when running. Oddly enough,the pump still puts out significant pressure but less than it should due to the leaking water. What is the most likely cause of this?..is it the high pressure water seal(s)? If so,how do I repair it?


... Pressure Washers

I have a LG Dishwasher LD 14AW3 it fills and runs for about 30 min. It then appears that when it tries to rinse it cannot get water and flashes "1E". I disconnected the unit and when I moved it out of its position water was leaking from the bottom of the unit. after cleaning out the inside filter & the hard water filter I re-connected and found it worked. I ran a dishwasher cleaner through it at high temp. After a few loads the problem has come back. It is now located in MY garage waiting for me


Found a leaking component that was causing the foam float located and attached to the inlet valve to shut down the water inlet and the water inlet Solenoid was also sticking. I found out this simply by tapping it while it was trying to get water for ... LG Dishwashers

Hello, I have a Kitchen Aid dishwasher, model KUDS30IVWH3. The dishes have not been getting as clean lately, the bottom is decent but the top rack is not getting very clean. Also, when I open the door after the cycle is done, there's a bunch of detergent at the bottom of the door and on the floor of the dishwasher, like it isn't getting sprayed all over or something. Don't know if I have to check the water intake valve or if maybe the sprayers could be partially clogged.


... KitchenAid Dishwashers

I have a Karcher K3.48M electric pressure washer which used to shut off when you weren't using the cleaning wand. This no longer happens and there is alot of water running out of the bottom of the unit. (This didn't used ot be the case) I expect a leak somewhere inside the unit, but I'm wondering even more if there is a pressure switch which has failed that cased the leak. In other words, if I find and repair the leak and there is a failed pressure switch, it will likely only break again. I can'


Hi you will have a 8 digit number on a silver plate on the machine with a number like 1.141-470.0\015\012Then go to www.karcher.com then on the left click on Europe, then you ... Karcher PSI Electric Pressure Washer

Hotpoint hda 3420 dishwaher. when turning, on the motor hums and doesn't kick in like usual. manual says caused by non use. "must keep the seal moist" put water in the unit, thinking it might get the seal moist. bottom filled and unit has not worked for days. assuming it's this seal: where is it? how do i get at it? what is replacement difiiculty? how much is the part? thanx ron [email protected] or [email protected]


Hi,Before thinking about replacement... pour a couple of cups of water in the dishwasher and let them soak the seal for overnight...Then if it don't go give the motor a spin...just to make sure it will go...if that don't work ... Dishwashers

My SB908WL Westinghouse dishwasher is tripping the switch when it goes to pump out the water. What are the likely problems and solutions please! If anyone has some expertise that would be great. (I have recently checked the soldering on the main panel and touched one point up, the rest are fine it seems). The element is working as there is hot water in the unit. We have small kids so maybe something is jammed in there? How do I get access to check. All input helpful. Thanks!


... Dishwashers

The top rack isn't getting clean. Could this be a pressure problem our an internal problem? It's not whishing like it used to. The water isn't reaching into the glasses. I think the only water getting to the top rack is what is sprayed onto the bottom rack dishes.


My husband told me to call a repair man rather then going through FixYa.Please take me off your mailing. Thank You ... Whirlpool Dishwashers

How to diagnose? My Kenmore won't run. First it was flashing the clean light 7 times, so I figured out how to reset ("High Temp Scrub"/"Air Dry"/"High Temp Scrub"/"Air Dry"), but when I try to run a wash, it sounds like it's not getting water into the tub. When I checked it several minutes later, it was in "Cancel" mode, making a sound like it was draining (or trying to drain), then the clean light started flashing 7 times again. Clearly, the machine has something wrong but I don't know where to


Once this code goes off, it is not going to run. The module has picked up ths issue as you said. I would check the sensor first. You can make sure it is getting current by testing the circuit. ... Kenmore Dishwashers

Our Kitchen Air KUDIo1Ilbl6 DW is 6 years old. The dishes are no longer getting clean. It sounds different in the washer. I question the pressure is high enough inside the unit. I ran vinegar through the unit, did not seem to matter. The temp is 140 the pressure from our well is the smae as when we installed about 55 psi. I checked te screen it seems to be clean. Any thoughts


Hi\015\012\015\012If you are observing that the dishes are not clean, then you'll need to follow certain steps to be sure where exactly the issue. First thing to check for is the detergent cup and spray arms. Check if the dishwasher's sp ... KitchenAid 24 in. KUDI01ILBS Stainless Steel Built-in Dishwasher

Bosch Exxcel model number SGS46E12GB had the check water light on a week ago, checked supply and cleaned filters, all good. light still on, got upset and slammed the door, light off. since then the unit will either wash stuff, or not. didn't seem the arms were spraying very well when I opened the door, so I bypassed the door switch tonight and put it through a pre rinse cycle. (I ran it with the bottom filters removed) upshot is the pressure of water was really poor. also, when I first turned


... Bosch 24 in. SGS47E02 Exxcel Free-standing Dishwasher

Pressure Once I have the powerwasher started and going (water to it before starting) i can't get it to go to full pressure it will prime up like it's going to go to full pressure give me just a shot of full pressure then go back down to probably half pressure and remain there then prime again for a second then back a coninues cycle! Maybe there's a seal or something somewhere I should look at. Hose and pressure from house is good, the seal whee the hose attaches to the bottom of the washer is ne


This is usually a problem with the "dump valve" defective in not being able to hold the pressure but only able to release it prematurely as it should only do so when to much pressur is built up inline. Only recommend qualified pump tech. But check pu ... Coleman Pressure Washers

My Karcher 411A seems to have lost pressure. Behaviour is this, when you press the water release on the spray gun you get 100% pressure for like 10 seconds and then it seems to dwindle down to 30-40% of its total pressure. When the pressure cuts down I can hear more noise coming from the gun sprayer aswell. So not sure if the problem is in the gun or the main pump unit ?


Sounds more like a clog on the intake side. Check the filter and the hose on that side. ... Pressure Washers

My Haier dishwasher is leaking badly from the bottom of the unit. I took the back off and checked the connections; all are tight. It looks like the water is dripping from the inside of the unit near the front right corner of the unit. Any recommendations?


... Haier 17 in. HDT18PA Built-In Dishwasher

Excell vr2500 pressure washer ,no pressure, took off high pressure hose at bottom of washer , get water flow, but flow does not change when engine is running full throttle


Check the water filter ---high pressurehose must have bbackpressure to develop pressure so disconecting it wont acheive ,much ,if you have agood water supply ,oil in the pump--- adjust pressure by srewing the brass fitting that the pressure hose atta ... Pressure Washers

Hobart LXIC under counter comerical dishwasher. Delime lled keeps comeing on every time power up. Checked sensors on bottom in the water drain area senser on right (there are 2 next to each other on this unit I think other is water temp) the wire had wire burn completely off. I reconnected the wire and started to burn up the wire again. Question: 1) Is this sensor for the Delime sensor? 2) does it sond like the sensor is shorted to you? or sending wrong voltage to sensor? 3) If no


... Hobart 24 in. LXIC-5 Built-in Dishwasher

Meile G894SC the bottom rack does not clean bowls seems like it's not getting enough water to spin the nozzle. How do I check to make sure it is clear and the pump is passing water to all three nozzles?


... Miele Touchtronic G892 Built-in Dishwasher

Hi have a Karcher 6.91 and I cant get any water pressure. I have checked the o-rings, filter and lances but it does not build up high pressure.


... Pressure Washers

I have a Whirlpool Gold Quiet Partner III that is 8 years old and recently stopped cleaning top rack dishes. I remember finding a mylar like piece in the bottom of the tub and threw it away thinking it came off of something we washed (I know, bad thinking.) The mylar piece measured roughly 3-4inx2in and was folded in half. Anyways....the upper arm does not spin and the detergent doesnt get fully dispensed so dishes dont get fully cleaned. I am guessing not enough water pressure to upper arm. Wou


I'm having a similar issue. Are you sure the arm isn't moving at all?\015\012\015\012Generally what I'm finding is either you have a clog or the pump motor is bad.\015\012Hear is the service manual.\015\012 ... Dishwashers

I have a Comet BXD 2525 G pressure washer pump which is giving me some problem. (Maybe) I hook the water up to pump and the pressure hose up to the pump, turn on the water and the water sprays out of the water connection at the pump. I check the hose to see if it was clog ok and the next was a the water connection ok. It's like the water is not going int the pump. When i start the pressure up the water come out of gun but no pump running like it should. The next thing i was going to look at i


The water inlet needs a gasket like all hose connections. If its gone the pump may be starving for water. ... Comet Pressure Washers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.2093 seconds