Having problems with your Electrolux Dishwashers ?

I have dishwasher (Electrolux) model ewdw6505gs. How do i clear a code of 01? I fixed the disposal clog and the dishwasher automatically drained the water in the bottom. I just can figure out how to clear the error code.


Answers :

I should inform you that that is a "leak detection error".\015\012You should check some of those hose clamps, they may not be tightened properly.\015\012
\015\012Regards
Repair Help & Product Troubleshooting for Electrolux Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have dishwasher (Electrolux) model ewdw6505gs. How do i clear a code of 01? I fixed the disposal clog and the dishwasher automatically drained the water in the bottom. I just can figure out how to clear the error code.


I should inform you that that is a "leak detection error".\015\012You should check some of those hose clamps, they may not be tightened properly.\015\012\015\012Regards ... Electrolux Dishwashers

My asko d3250 thinks the drain hose is blocked. but when i pour water in the dishwasher to see if the water is being drained, the dishwasher is draining properly. Yet the dishwasher after it has drained the water, will shutoff and start flashing the Large Pot icon (drain hose is blocked error code). Is there a sensor that is faulty?


Yes, it sounds like it is to me. I'm not able to pull your model up on my data base,if I could I would be able to tell you where it is located. I would assume that it's located either inside the pump or close to it. Sorry I couldn't be more help. ... Asko Dishwashers

AEG OKO_FAVORIT 6281i dishwasher - error code 20 (Siphon blocked). Out of the blue after 6 years of reliable once-a-day family use, my AEG OKO_FAVORIT 6281i dishwasher started OK but about 3 minutes into the cycle began flashing error code 20. At which point there was a litre or two of cloudy water sitting at the bottom of the machine. Since then I've tried redirecting the drain hose into a bucket, after disconnecting it from the kitchen drain. Same symptom, and no outflow except what was al


... AEG 23 in. Favorit 50750Vi Built-in Dishwasher

We just installed a Fisher & Paykel DD603 dishwasher. Intially it would not drain correctly. And, proceeded to flood the bottom and set off the F1 error code. I dried out the bottom to get the F1 code to stop, which it did. After adjusting the leveling the dishwasher drained both drawers correctly, once. A few minutes after the rinse cycle had finished and the drawers were empty of water the F1 code started again. Now it will not go away unless I unplug the machine. I dried out the bottom very w


HI. The original code(f1) is in reference to a overfill condition. This may be a clogged drainage Assembly. This condition will usually cause the control sector to short out if not corr ... Dishwashers

A feew weeks ago Smeg STA6047 dishwasher stopped in the beginning of the programme after approx. ten minutes, and gave the error code E9. There had been clearly water in the machine, but maybe not enough and the detergent box was not open. However, when technician came by two weeks after, the dishwasher worked and he said it was in order. But only after being used only once, the same problem reappeared. First the washer gave the error code E8, on the second try E9. And now it does not start at a


As you know E9 is linked to the water inlet problem. \015\012\015\012There are two scenarios here - 1) Are you using the Aqua-Stop safety system? If this is trigerring then it can shut the inlet water. The reason it can trigger is if the ... Smeg Dishwashers

Hi there, The error code 'strong and economy light flicker fleetly' is showing. the manual says that this means too much inlet water. We have drained the machine, cleaned waste pipe and tried to operate with a reduced flow from the inlet pipe but it's still not working. I filled the base of the dishwasher with water to see if it drains properly. It seems to be draining, but also leaking out of the base as well..? Any ideas?.


Hi The issue seems to be with the float switch assembly that is bad and should be replaced. Float assembly is found inside the dishwasher's tub, on the bottom. The water that ... Baumatic Dishwashers

Our dishwasher beeps twice when the start button is pressed but then doesn't do anything and there is no other noise from anywhere (eg, motor/pump). There are no error codes displayed and the display appears normal (ie lights up and shows time for program completion etc). When the problem first occurred the machine was full of dirty water. We have turned the dishwasher off and on at the wall, checked/cleaned all filters, drained the dirty water and still nothing happens (it doesn't even fill


... LG 24 in. LD-12BS6 Stainless Steel Free-standing Dishwasher

Dishwasher not draining E25 error code (Bosch exxcel) . I have cleaned filters & removed pump inspection cover to check / clean debris I have also checked the waste water pipe is not kinked, it runs for 1hr 15 mins last time and then cut out with the error code displayed.


Gr8 stuff klaudi & Nypmh - rocking it back 45% worked a treat. Bloody BonzaShell XX ... Bosch Dishwashers

Our kitchen drain clogged recently and water drained back into our VUD141 dishwasher. A plumber cleared the drain, and turned on the DW - which pumped out the standing water. But now, we have no water flowing into the dishwasher. The drain pumps, the heater works, but there's no water supply. The plumber who cleared the drain said he didn't DO dishwashers, and I cannot locate the owner's manual since we prepared for a move.


Hi\015\012\015\012 \015\012\015\012When the dishwasher won't fill and the water supply is on,\015\012then the issue is with the water inlet valve which is either clogged or\015\012blocked, you can try to clean it. If this wont so ... Viking 24 in. Professional Series VUD141 (Ultra-Premium) Built-in Dishwasher

I have a Bosch Dishwasher Model # SHU43C that is not washing properly. Some dishes are not being cleaned if we don't pre-scrub or rinse. There are no error codes on the panel. During the cycle I hear the pump motor starting and stopping repeatedly on about 1 second intervals. I suspect it may be starved for inlet water. I checked the inlet water line and it is clear. We use well water that occassionally has some iron sediment in it and it plugged the inlet water screen for our washing mach


Hi,\015\012It is very possible that the screen is plugged...most inlet valves have a screen just like your washer does. I would at least remove the hose/pipe and check the flow...and check for a screen. \015\012Also the solenoid can get j ... Bosch 24 in. SHU43 Built-in Dishwasher

Dishwasher starts to fill then goes to drain drains all waters shuts down and all lights flash displays error code 12 drain valuve.


Hi\015\012\015\012Error code F12 means a shorted connection or wiring on keypad. Turn off & unplug the dishwasher for 2-3 minutes and check the error doesn't appear. If this doesn't resolve the issue then you'll need to disassemble the ke ... Electrolux EIDW6105GW 24 in. Built-in Dishwasher

Standing water in bottom of dishwasher--get F2 error code. It works if I drain all the water before cycle by using a turkey baster


Sounds like the drain pump on this unit is bad //you may luck out and tear into it and remove some debri from the impellar but they are made mostly of plastic these days and normally go bad... disconnect the drain hose from its termination point usua ... Asko Dishwashers

Bosch Exxcel Dishwasher (Enr SMS53E12GB/01 FD 9002) bought in July 2010. Error code 15 and "Check Water Supply" light on at same time. Have checked in-line filter in tap connection and all clear, water pressure OK, no kinks/twists in supply hose. Any help would be greatly appreciated - I'll have to call Customer Service in the end as it's outside of my problem-solving ability, but would like to check whether there's a known reset or fix I can try before I call.


... Bosch 24 in. SGS47E02 Exxcel Free-standing Dishwasher

D1756 Dishwasher has an error message of "F2" and won't allow you to clear the wash menu. I have drained all of the water out from the bottom of the dishwasher and checked the discharge hose for blockages, but problem remains. Is there a re-set mechanism that I need to re-start the washer? Thank you Regards Howard


... Asko Dishwashers

Hi I have a GE Dishwasher model gsd2200g -03 and I am getting C1 & C2 error codes but it seems to be working fine. I disconnected the drain hose and the water appears to be draining properly


Hello there: if you have installed a new garbage disposal make sure the knock out has been removed if removed then check the drain valve in the pump hope this helps you out sincerely D.Jones ... GE Profile PDW9880NSS Stainless Steel Dishwasher

Towards end of dishwashing cycle error code comes up and consitently beeps, can not turn off by machine buttons or reset. We have to reset by power plug. Water is left in bottom of macine, dishwashing powder is left on most things. Rinse button then works, it then drains the machine no problem. So I dont think it is the pump.


No response ... Dishwashers

ASKO D1976 model. We have a F2 error message. Water has now been drained but we are unable to remove error code or have dishwasher return to normal cycle


Display shows an error code. Do the following:1. Unplug washer or disconnect power for one minute. 2. Plug in washer or reconnect power. 3. Re-select the cycle and press Start.NOTE: If the error remains on the disp ... Dishwashers

Bosch dishwasher model shx36l fails to stop pumping. The drain was clogged. I cleared the drain. Dishasher backed up, water overflowed. Clog has been fixed. Dishwasher will not stop trying to pump water out. There is NO water inside dishwasher. I wish to run another load however unit fails to respond. Pump is operating even when front door to doshwasher is open. Turning the power button to OFF is the only remedy to stop drain pump from operating. How to fix?


... Bosch Integra® 500 SHX46A0 Dishwasher

Samsung Dishwasher can drain, but gives "drain error"


Sounds like it could be those same water level sensors you worked on before. Only now its telling the thing that there is water still standing in the unit. Try cleaning those sensors again and I know this sounds obvious but check all your conections. ... Samsung DMT400RHS Builtin Dishwasher

Diplomat dishwasher error code F4? not draining water away?


... Dishwashers

Error code e6 on stoves dishwasher 600dwt. doesnt run all the way through. it has water in it and it drains.


... Stoves 27 in. DW60 Built-in Dishwasher

Asko 1555 Dishwasher will not drain. Bottom of kick panel pan will fill with water triping the float switch?, leaving an error code. Is it safe to assume that the out pump needs replacing. I had the kick panel off and smacked the motor housing a few times and it ran for a few loads, but is now again stopped working.


It might be the pump, or it might be an obstruction elsewhere. If you have an air gap on your sink/counter top, open it and check for debris. If it is clear, unscrew the main filter basket. There is a black plug on the left side of the bottom well ... Dishwashers

Getting error code 0E on LD-14AW3 model dishwasher after 2 minutes. Checked drain hose and water seems to be coming out but won'y go any further in cycle Also makes a loud humming noise when running.


To little info, but looks like pipe is much to low. Not getting the opportunity to fill up properly.Raise it higher.(Im asuming that you can hear the drain pump run and water is being pumped out as wall. ... Dishwashers

Dishwasher is not draining properly - standing water in the bottom of the machine Error code 04


... Electrolux EIDW6405HT Builtin Dishwasher

LG LDF8812ST dishwasher not washing: reports LE error code. Fills and drains ok. Impeller is clear, removed inside housing - no obstructions. Synchronous motor works. Tested main motor - appears to be good. Motor is not locked, looks to be in excellent condition. No shorts to ground, continuity across three main pins - not sure what the other 4 are for. My guess would be the PCB, but not sure how to test this. How do I determine if the PCB is bad?


... LG LDF9810ST Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.2020 seconds