Having problems with your Electrolux Dishwashers ?

I have a frig/electrolux gallery series dishwasher: model GLD2445RFC0 serial # TH72896159. On the ceiling of the dishwasher is a gray plastic arm that snap onto a round gray disc that screws into the ceiling. It will not stay connected to the disc eventhough I snap it on with a round white plastic doughnut kind of cap. I have replaced the gray arm in the past because the orig. one fell and melted on the heat ring. This one has : 1546496 1546079 CAV 2 >PP+20TF written


Answers :

If you go to searspartsdirect.com and type in 154607802 for the part #, I'm pretty sure that's what you are looking for. I broke the exact same part and it's what my husband ordered as a replacement.
Repair Help & Product Troubleshooting for Electrolux Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have a frig/electrolux gallery series dishwasher: model GLD2445RFC0 serial # TH72896159. On the ceiling of the dishwasher is a gray plastic arm that snap onto a round gray disc that screws into the ceiling. It will not stay connected to the disc eventhough I snap it on with a round white plastic doughnut kind of cap. I have replaced the gray arm in the past because the orig. one fell and melted on the heat ring. This one has : 1546496 1546079 CAV 2 >PP+20TF written


If you go to searspartsdirect.com and type in 154607802 for the part #, I'm pretty sure that's what you are looking for. I broke the exact same part and it's what my husband ordered as a replacement. ... Electrolux Dishwashers

Hi I the white plastic insert that holds the left arm on the mamaroo swing has snapped top and bottom :( can I get replacement ones please? And where would I do this?? Thank you x


... Dishwashers

I want to remove the white plastic wheel that propels water into the circulating arms. It is held with one screw which I cannot seem to be able to loosen. This white plastic wheel has 2 small holes in the surface which are perhaps there for some special tool to hold the wheel stationary in order to loosen the screw holding this wheel in place. Underneath this gray plastic housing is the heating element. I want to remove it in order to clean accumulated deposits of gunk.


It's reverse threaded. ... LG 24 in. LDS 5811 Built-in Dishwasher

Dishwasher wasn't cleaning, tried cleaning the top spray arm but broke the hook that holds the top spray, looks like a 1/2inch gray plastic nut/bolt with a split prongs at the top. One prong broke so arm will not stay on. Where do i find this nut/bolt/hook. The LG customer service was of zero help.


Hi,\012That is not that hard to fix and you can easily buy the parts yourselfonline...Here is a tip that will help you with the online buying...How to Buy ... LG LDF6810 Built-in Dishwasher

My dishwasher spray arms were clogged with calcium buildup so I cleaned one and replaced the other. I also removed the fixed disc-shaped device underneath the lower spray arm and found the particle filter was clogged- so I cleaned it out. The dishwasher ran fine for a few times but then the filter clogged again, and again, and again. Now I need to make a routine of disassembling the parts to get at the filter every week because the filter no longer clears itself during the wash and/or emptying c


You may want to check your hot water tank. It may need drained and cleaned, Or you may have the rod in the tank disintegrating. Also check you water faucet areators to see if they have calcium pieces too. ... Maytag Dishwashers

A part fell into my top tray,gray,plastic,9 inches long w/ a 2 inch diameter circle in the center,looks like its an arm,spinning somewhere?....did it fall from the inside "top",side,bottom??? Don,t know where to attach back?What is it,where does it go,can it just snap back ???? Thanks for any help...MODEL FGHD 2433 KFO...Serial # [email protected]


Here is the exploded diagrams of your entire machine.\012Locate the patr and you should be able to figure out where it goes\012\012 ... Frigidaire FGHD2433KF Builtin Dishwasher

Poor washing The soap door opens but soap still in there after wash cycle. We got lower spray arm off and one plastic piece but can't get all the way to the pump. Pump appears to possibly be cracked so we suspect it needs replacing, but we can't get it out.


Before you suspect the pump and motor assy, do you hang the silverware basket on the front side of the lower rack or if not did one of the holders for the rack fall off and you replaced it? I have found that id the basket is hung on the rack that tal ... Whirlpool 24 in. GU1500XT - Multiple Color Built-in Dishwasher

Hi, switch underneath our miele g646sc washing machine burnt out. It is situated in a round case, with a polystyrene disc above it. The whole of this plastic case, abour 3" dianeter is clipped under the main body of the machine. Do you know what this one does so that we can try and rectify any problem that has caused the burnout, and any idea of part number or where we can see an exploded part drawing? Thanks! Steve


It is usualy caused by dampness from water in the waterproof tray. the switch is for flood protection.a miele service agent would be your best bet ... Miele 24 in. G646SC Plus Free-Standing Dishwasher

My dishwasher's top rotating sprayer keeps coming loose. The screw and plastic bearing fall out and I think that it has stripped out the end where it seats into the top of the washer. Any ideas on how to anchor this in? Adhesive? A larger screw? The plastic bearing is Part No. 568 and the screw is Part No. 569. If I replace the conduit arm (Part No. 585), will that give it a new, clean spot to screw in too? How difficult is it to replace this arm?


\012Hi,\012That is not that hard to fix and you can easily buy the parts yourself online...Here is a tip that will help you with the online buying...How to Buy ... Dishwashers

Sears dishwasher 665.15882000 part #8268296 fell off and I can't find the "screw" that holds it in place...probably went down the drain. Now dishes do not "dry" on air dry. The part that matches the number for replacement parts does not look at all like the one that fell off. The one I have is round and the replacement one showing looks like some funky ninja weapon. Will this work on my machine? How easy is it to replace this part?


... Dishwashers

The top spray arm of my Frigidare model FBD4315LFC0 Aqua Surge dishwasher fell off. Their appears to be a missing part. I've been searching online for a schematic and can't find one thorough enough to use. The parts I have are: 1. The top sprayer arm (the one in the top of the tub) 2. The two piece plastic keeper ring that appears to fit into the top of the spray arm. 3. A small white grommet looking item that fit inside the keeper nut. 4. The keeper nut that screws directly onto the wate


Hello there:hey sorry i keep getting disconnected i will be back on really soon i need to find out what is going on i hope these things that i have discussed with you is helping you out the parts are not as hard as they look once yo ... Frigidaire 24 in. FDB435RFR Built-in Dishwasher

WATER SRAYER ARM BROKE OFF.HAS A SCREW TO TAKE OFF ARM, ALL I NEED IS ONE ARM TO REPLACE THE SPRAYER ON BOTTOM, DON'T NEED THE WHOLE UNIT..WHERE CAN I PURCHASE ONE?


\012Hi,\012That is not that hard to fix and you can easily buy the parts yourself online...Here is a tip that will help you with the online buying...How to Buy ... Jet Tech Systems Dishwashers

SHE6AF06UC/03 upper wash arm came off. Have arm (d'uh) and round piece that goes thru it. Seems to be another piece that connects arm assembly to top of unit as that round piece can't snap into what is still there. Need exploded view diagram to determine what piece is missing ('cause can't find any other 'other' pieces in the unit). thx


Hello,\015\012\015\012Welcome to FixYa.\015\012\015\012If you follow this link below and save the file and then open it,( pdf about 5mb in size ) refer to page 21 it will illustrate how the upper arm ... Bosch Dishwashers

The spray arm, above the top rack, keeps unscrewing during the wash cycle. Just the arm comes off leaving a round plastic part attached to the top. This can be unscrewed and inside is a white 'washer'. The arm can be clipped back but comes off again in the next wash. The plastic 'washer' has to be turned over to allow re-attachment. Is a washer missing from inside?


Could the arm be mounted upside down and rotating the wrong way? Just an idea... Some of these can fit either way and the retainer will fit either side of the arm. ... Frigidaire 24 in. PLD2850 Built-in Dishwasher

Maytag Dishwasher circa 2002 - Defective Plastic rollers The plastic rollers that slide the arms of the dish rack keep breaking. I have had this dishwasher for 6yrs now and go through 1 a year. This defect is really annoying for two reasons one; the cost - $50 each - X's 6 years = $300. Secondly, the inconvenience of having a delapitated dish rack that crashes sideways - with the weight on only one side. Presently, I'm about to order my 6th one. I'd like to know if you are aware of this d


... Dishwashers

Plastic Pieces We purchased our ASKO 1385 dishwasher 7-8 years ago. Over the years, I have found "small square, thin, pieces of gray plastic" inside. Where are these coming from? Also, we have replaced the drain pump 2 years ago and looks like we'll be replaced the main pump within the next few days as no water is going through. We are looking at paying big $$$ for that pump. Almost half as much as purchasing a new dishwasher. Is this a common problem?


Yes, I have the same problem and it is the upper bearing rack, not the pump impeller. The new bearing kit is $30.00 (another is available for $123.00-the same!!). ... Asko 1385 Dishwasher

Top arm does not turn in most of gibson amana an frigidaire this is done by ball in bottom of pump .it is clean.spray arm are clean .bottom arm move all the time.timer works it hesitates every so often and so ball will move an water should go up to upper arm but doesnt.common problem on these units but dont know how to cure?change ball.didnt work..on one unit changed pump cure problem for 4 months then returned....also does anyone know were u can buy the plastic they used to sell for dishwashers


Can yo give me the make and model number sol I can look at the service manual for you? ... Dishwashers

I am trying to install a new Maytag MDBH945AWB Dishwasher and have to run the drain hose under the machine in order to get it to the sink. Each time I try to use the hose that comes with the machine it snaps in two and breaks. I have tried to look for a replacement hose that would stand up to the abuse but all I can find is the original. Is there a replacement I can get that is more flexible than the one that comes with it? At this point I am rather embarrased about going back to Home Depot


Hi...home depot sells clear PVC hoses, They come in various lengths up to 100 ft. You can use hose clamps to connect it to the T-fitting. ... Dishwashers

Maytag My Maytag dishwasher is leaking from the bottom. It is a mdbh940aww. it was never used before. It was wrapped in the plastic wrap when I bought the house in 2005. Now the old one just went and I want to put this one in. It fit nicely, works great but leaks all over the floor. It is level and I check most of the parts. I put a mirror underneath and it looks like the rubber thing isnt looking too good. Do I replace this? If so how?


I also had a mdbh940aww that leaked from underneath. You need to check out where the water is leaking from. Unscrew and remove the bottom front panel so you can view under the dishwasher. Start up the dishwasher and using a flashlight see where th ... Dishwashers

I have a HJA8630 dishwasher from Howdens. The small grey plastic clip which stops the metal runner at the top from falling out has snapped. it is the one at the rear of the machine not the front one. I need to know where to get this spare part please!!


... Dishwashers

The upper spray arm keeps falling off. If I order a new one, will I get both the arm and the piece that it snaps onto which is fastened to the inside top ?


... GE 24 in. GSD5120 Built-in Dishwasher

About a 3 year old maytag stainless steel inside dishwasher, not cleaning, often soap resdue on dishes or silverware, I use fresh new cascade, checked to see if washer fills with hot water, seems to up to the bottom of the door when I open durning cycle, arms go around, no obvious plugging of the screens, no junk in the foot chopper propeller, no paper or plastic or food in the jets of the arms. Motor went out on it 9 month ago and I had it replaced by appliance repair station here in Missoul


Water must be 130 Deg F to wash properly. ... Maytag Dishwashers

Miele dishwasher G2870 scm. There is an F14 fault. I have cleaned the arms removed the waste basket from the bottom of the dishwasher and removed the two parts one with the large metal ball to expose the plastic wheel clog. There does not appear to be a blockage. I also removed the top arm and cleaned that out. I don't know what other inlets to check as the guide does not tell me exactly what an F14 fault is but explains F11,12,13. Can you help?


F14 on your model of dishwasher is indicating a blockage, poor water\015\012pressure or could be a fault with the pump pressure level switch or\015\012circulation pump.Filter and non return valve is cleaned of any blockages and if the fau ... Dishwashers

Component failure Actually a Kuppersbusch IGV 645.2 Dishwasher There is a plastic conduit which takes water from the base of the machine to the upper spray arm. This now comes adrift from its connection at the base (behind the lower spray arm) on every cycle, resulting in poor or incomplete washing. It can be replaced easily and seems firmly inserted when done but is always adrift again by the end of the next cycle. Anyone any ideas?


Put a bead of silicone on the tube connection and let it set up good before running. If the tube is in good shape and only comes loose this should be an easy fix. ... Whirlpool GU2400XTP Built-in Dishwasher

How do i put the lower spray arm back together? I had to replace the top screw part and it seems to stand up to high. I have a small white plastic ring, a larger white split ring and the arm itself. I have tried every configuration to put this back together but it is not right - the new "screw" part number is the same as the original.


... KitchenAid 24 in. KUDS25SH Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1162 seconds