Having problems with your Electrolux Dishwashers ?

Got dx303sk dishwasher heater not working a new one was fitted two months ago now stop heating any idea


Answers :

First of all check the continuity of the heaters as if the heaters are open there will be no heating. Now if the heaters are good then the fault is with the switching, so your focus now must be to see the area of fault of the program switching.
\012Check for loose wires, poor connection or faulty connectors.
\012Have the test of continuity with the power plug removed .
Repair Help & Product Troubleshooting for Electrolux Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Got dx303sk dishwasher heater not working a new one was fitted two months ago now stop heating any idea


First of all check the continuity of the heaters as if the heaters are open there will be no heating. Now if the heaters are good then the fault is with the switching, so your focus now must be to see the area of fault of the program switching. ... Electrolux Dishwashers

New SHE4AM16UC, professionally installed eight months ago. Worked fine with very light usage until now. Dishwasher starts normally but stops and signals "clean" after less than five minutes on any cycle. One inch of water in bottom that (I think) drains when a new cycle starts. Soap tablets are not ejected from compartment. Bosch authorized repairman says he now has two client dishwashers with identical symptoms and is asking Bosch support for ideas (he's changed pump, control unit, and float sw


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks\015\012for using FixYa. If the clean light flashes, pauses, and then repeats.\015\012When the dishwasher doesn't sense a water t ... Bosch SHE4AM16UC 24 in. Built-in Dishwasher

I have a Kenmore model 665. It is having an intermittent problem. It goes through the fill cycle, and then stops. Timer does not progress either. Then, at some random moment, it will come back on and finish the entire cycle. This could even be a day or two later. Sometimes it seems a nearby thump will set it off, other times no one is anywhere near it when it comes back on. This happened for a month or so off and on 6 months ago, and then it worked fine for 6 months. Now it's back to it.


Its possible its a door switch thats causing this or the main wire is loose..be careful as you do have 115 volts. i'd turn off power and check where power comes into d/.w and make sure the wire nuts are tight.. the next step is a little more difficul ... Dishwashers

Coleman mobile home furnace...Model number DGAA077BDTB...The furnace about a month ago started going out ( flash code- Combustion Air switch stuck closed)We replaced the thermostat on the wall and it stopped doing it and ran fine then last night it stopped again ( Combustion air switch failed to close) and when i got up the furnace was working and now for the past few hours it refuses to do anything...I am on a very very tight budget...and need some idea of what is wrong and do i need a professi


I had the same errror code on my coleman furnace (3 flashes combustion air switch failed to close) but at first didnt realize there was even a light that gave codes..Anyways long story short, after searching many forums one guy mentioned about the fu ... Dishwashers

Dishlex Global 300 Fills and then stops. faint electrical smell after a while . Checked heating element that I replaced 8 months ago, seems OK. It has 29X? ohms resistance and looks OK. (I am not sure of the reading on my meter but the element is not fused.) Pumps water in and out OK No blockage in pump or filters Water level looks to be low on filling, only part covers the heating element. I tried instruction book on changing water level using the "Eco" button no response as indicated in


You need to open the front cover and check the wiring for any burnt wire,this happen sometimes,if that does not solve then it't either pcb or electric motor causing this smell.You would be better off with a new one then. ... Dishwashers

Hi I have a Zanussi ZDF501 dishwasher that stopped heating up intermittently. It got worse and I fitted a new heater and all was ok for a few months. Then the intermittent failure started again. Note that I tested the old heater and it is actually OK without a short circuit so I don't think it was the problem adn can be re-used. Could it be the thermostat or heat sensor? I am concerned it might be the PCB since the failure was intermittent. Thanks Dave


In my case, although the solder joints on the relay looked poor, improving them didn't help. I had to replace the relay. Fortunately, Maplin stock a compatible one, JM67X for 1.99. See ... Zanussi Dishwashers

Dishwasher problem Hi We have a Whirlpool GU 2300, the machine has stopped and is the clean LED on the control panel is showing a 7 pulse sequence which I guess is a fault alarm. I have tried resetting, checked the door switch and looked at the pressure sensor at the drain pump outlet. I changed the heating element and fitted an uprated control card earlier this year. Any ideas?


I solved the reset by pressing the air dry and reset buttons 6 times in sequence, the whole panel array lit and I was then able to reset. I have had no problems since and have used it 6 times. I initially thought that the chipset had a volatile memor ... Dishwashers

8575637 Brand new dishwasher installed about a month ago. Its been used about 10 times and in the middle of a wash cycle, completely stopped with no power. Have checked the plug, outlets, breakers. Cannot get any of the buttons to light up, have checked to make sure it wasn't locked out - no power at all. Manual is not helpful. Any ideas?


... Whirlpool GU2400XTP Built-in Dishwasher

Dishwasher not working. Two weeks ago the heating cycle didn't switch itself off but appeared to correct itself. Now there is no water in the cycle... pump and heater working, just no water reaching the arms of the dishwasher. Any ideas why?


Sounds like a bad pump. If it drains the water and doesn't deliver at arms the pump is more than likely bad. First of all pull the water supply line off and see if there is build up from hard water on the in-line screen (if present), then If you are ... Whirlpool GU2400XTP Built-in Dishwasher

About a month ago, our dishwasher stopped working properly. It runs fine and the soap is being used, but the dishes are not being cleaned and especially on the top rack. I opened the dishwasher this morning while it was running and I noticed that the coil on the bottom was red (maybe heating water) but only about 1/16th of it. Could this be the problem?


Hi\015\012In a dishwasher you can see the water trickle upward to the upper nozzle in dishwasher...but if it does not have enough pressure,it will not function properly.tap the delivery tube that feeds this nozzle and you will see the water pre ... KitchenAid 24 in. KUDI02IRBS Stainless Steel Built-in Dishwasher

GHD hair straightener Hi my GHD hair straightener suddenly stopped working. The fuse and plug seems fine but there is a continuous beep when I put it on and it goes off on its own in sometime. The plates are not even heating up Can anyone help pls? I bought it only a month ago by ordering online from GHD official website Is there someone in Bombay who can repair it?


... Dishwashers

My dishwasher emits a dead animal smell immediately after filling. I have a 20-year-old KitchenAid KUDS220T3 dishwasher. The racks are a little corroded, but it still cleans dishes just fine. About two months ago, it started smelling like a dead animal immediately after the dishwasher fills with hot water, during the time the water is being heated, but before agitation begins. The smell appears to be coming from around the door. If I open the door, everything inside the dishwasher smells fine.


This vent that you are describing is to allow air to flow in for the heat/dry cycle. Some times little creatures want to "mark" their territory by "spraying". Spray some type of cleaner like ammonia into it and **** it out with vacuum a few times. Mo ... KitchenAid Dishwashers

I have a Frigidaire dishwasher, Model FDB15000LFCO. Serial No. TH74135326 purchased 10-19-07 from Lowes. The washer stopped working almost immediately. On December 5, 2007 the computer brain for the washer was replaced by Able Appliance Service, LLC, Swannanoa, NC (828) 296-1017. Four months ago my electric bill for three months was almost twice my average use for the time period. We stopped using the dishwasher for one month, and the bill returned to normal. Was one part in the dishwasher in


I think you have one 0 too many in the model no. should have been FDB1500LFCO. The user manual is available here.\015\012 ... Frigidaire Professional Series 24 in. Built-In Dishwasher Dishwasher

Kenmore 655.13222 k601 bought 5 months ago after


... Kenmore 24 in. 17032 Built-in Dishwasher

Over the past two years, the machine has occasionally stopped in mid cycle, while the pump continues to run, but the cycle stops advancing. Each time there has been water in the plastic pan under the pump, valves, and other mechanisms. The float switch has been tripped, stopping the cycle. Occasionally. but not always, the pump inlet has been partially obstructed by food waste. After bailing out the pan, the machine will run normally for weeks or months. There is no indication of a leak into th


Please post the exact make & model # so we can be more exact.\015\012THanks!! ... Dishwashers

Dishwasher: Kenmore ultra wash sensor quiet guard plus. I'm in a rental so I don't have the manual or model number. A few days ago it just wouldn't start the wash cycle. When you press normal wash then start the no heat dry and lock lights flash every other second or so but nothing happens. I can hit the cancel button and it will make sounds like its trying to drain, and after about 5 minutes stops. I've done the heated wash/ no heat dry sequence to try to reset but no luck. Also tried turn


... Kenmore Dishwashers

Recently replaced the control board for Electrolux EIDW6105GW1; after nearly a month of working w/o any problems this evening the machine made it through the wash cycle and then stopped working (all lights on wash cycle door menu are flashing). Took kick plate off bottom to check control board and the leak dectector is lit. I can see no leaks in front and am reluctant to do anything else with this POS. I spent nearly $1000 on this 18 months ago and have already sunk over $300 into a new contr


... Electrolux EIDW6105GW 24 in. Built-in Dishwasher

ASKO D3121 dishwasher has stopped heating the water and drying dishes properly. There is np physical heating element inside the dishwasher tub..?? any ideas ??


Hi\015\012\015\012Please check this link to know how a dishwasher work…\015\012\015\012http://www.explainthatstuff.com/dishwashers.html ... Dishwashers

I have a Kenmore Elite dishwasher with electronic controls. When I set the controls press the start pad and close the door it will not start. The light on the start pad just continues to blink. This happened about six months ago and the Sears serviceman pressed two of the control pads simultaneously and this reset the controls. Everything worked after he did this. What are the two control pads that you press to reset the controls?


This is difficult to find out. Try different combinations. Otherwise get the information from the SEARS serviceman. ... Dishwashers

My Bosch SHU9925UC dishwasher will not stop cycling and come to an end. I also noticed that a couple of weeks ago it stopped beeping to signal the end of the wash. Can anyone help me please? Thanks for any ideas.


Go check this link it will help you http://www.applianceaid.com/boschDW.html#run\015\012\015\012Hope that helps......... ... Dishwashers

I purchased a Bosch dishwasher and had it installed into my new kitchen. It is plumbed and it does not work, a reapair man said it needs a new motherboard. My issue is that Bosch can't seem to supply central Wi. with this part. The repair place put the order in two and onehalf months ago and still cannot give me a date about when the part will be in. I have owned this dishwasher for five months and have not been able to use it once!


... Bosch Dishwashers

I have an 8 year-old Kenmore 665.16912 dishwasher. Worked fine until two days ago. Then it stopped working altogether: nothing lights up on the front panel. I have checked the 120 in the electrical box, the door switch is working, the thermal fuse is working and there is 120 volts at the white and black connections to the timer control board. I bought a new timer control board for $120 and that did not fix the problem. What else could be causing the unit to completely stop working?


If all are really good then the only thing it con be is the display (8269205) $25.00 part, if it's bad dishwasher wont run ... Kenmore 16912 Built-in Dishwasher

The glass xpress light on my Whirlpool GU 2400, Quiet Partner III, is flashing. I tried alternating the sani rinse and heated dry buttons, and alternating hi-temp wash and heated dry---nothing changed. None of the option buttons light up when they are pushed. and the time remaining stays on -- (two dashes), the dashes don't move. Any other ideas?? PLEASE


... Whirlpool GU2400XTP Built-in Dishwasher

I purchased a diswasher (Hotpoint)about 1-1.5 years ago. It's model # is HDA3400G02CC and its SS# is TH887451Y. I don't think I registered it. No Matter, Two days ago, my garbage disposal stopped working. I checked the outlet. It had power. The switch to the Disposal was next to the outlet. I assumed that the switch was wired from the outlet. It wasn't. Bottom line, the switch nut was loose. I tightened it and problem solved. When I turned on the dishwasher, nothing happened. It acts like


I purchased your service (telephone support) and the dishwasher expert contacted me. We discussed the issue, he made recommendations. I followed his advise and solved the problem. Before I could recontact him, he called to follow up on my progress. ... GE Dishwashers

My zanussi dishwasher zsf4123s stopped getting hot,i bought a new heating element but still does not heat up,though im not sure if i fitted it correctly


... Zanussi ZT485 Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0852 seconds