Having problems with your Electrolux EIDW6105GB 24 in Builtin Dishwasher ?

I have an electrolux dishwasher Model # EIDW6105GS1 that for the second time has stopped working and all the lights at the top control panel are flashing...what might this mean? I removed the panel down below the door and it appeared to be a drainage problem. The first time it happend was about 1.5 yr after purchase...(No more warrenty and no extended warrenty)...I drained the water in the pan below and it worked once again. After about a month I am having the same problem.


Answers :

Repair Help & Product Troubleshooting for Electrolux EIDW6105GB 24 in Builtin Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have an electrolux dishwasher Model # EIDW6105GS1 that for the second time has stopped working and all the lights at the top control panel are flashing...what might this mean? I removed the panel down below the door and it appeared to be a drainage problem. The first time it happend was about 1.5 yr after purchase...(No more warrenty and no extended warrenty)...I drained the water in the pan below and it worked once again. After about a month I am having the same problem.


... Electrolux EIDW6105GB 24 in Builtin Dishwasher

Control panel inoperable - 2nd time this has happened. First time repairman said "it was fried" because the panel is just under the countertop - of course this is how it is designed to be. Now it has happened again. My dishwasher is GE PRofile and is now 4 yrs. old. I have tried shutting off power and the controls still do not respond to touch.


Is it operable when the door is close? I'm having a similar problem. The console panel on the top of the door appears to be not working. No lights. No buttons will respond. However when the door is shut, I can squeeze a finger to the start button and ... GE 24 in. Profile PDW9280JSS Built-in Dishwasher

I own a 3800 psi pressure washer since two weeks. For the second time now the tip of the extended nozzle is leaking and makes it unusable. I have already replaced it the first time but today it happened again. This would be the third tip that needs to be replaced in two weeks.


Sounds like that wand or tip under engineered OR INCORRECT WASHER TYPE ... Pressure Washers

Mod# mdb7601aww.... When I press cycle key, say heavy duty, then close door the 2H light flashes. I press the start button and the unit will not start. I have shut it down electricly and get the same results. what can be the problem? The front panel with the start/delay buttons or the inside control panel? I like to figure this on out the first time because each of those parts are $100+.


... Maytag Dishwashers

Elite 665.13933K010 The touch panel is inactive. There appears to be no power to it. It has done this before twice...the first time I bumped the top of the door and the lights came on and it worked. Second time, I took it out of the cabinet, turned it upside down and examined everything looking for a loose wire or blown fuse. When I put it back together it worked. Any idea what is happening?


... Kenmore 24 in. 17482 / 17484 / 17489 Built-in Dishwasher

After installing the new Kenmore model 665.13293k I tried to run a short cycle. Nothing happened and the selector lights timed out. Checked water supply and filter screen - OK. Panel lights so power is on. I don't hear any sound from the electronic water valve when door is first closed.


... Dishwashers

Kenmore elite dishwasher stopped in middle of cycle with water still inside. Checked breaker. Replace the hole control panel, door latch from a used kenmore elite. Work for half a cycle and quit with water still inside just like the first time.


Here's your solution (free PDF) - Kenmore Elite Dishwasher Manual ... Kenmore 24 in. 16352 / 16354 / 16359 Built-in Dishwasher

Maytag HDB8600AWW Dishwasher had been making noise (thought might be water valve, like previous DW), eventually stopped draining water, water now in bottom, I've let sit for couple weeks, looked inside, water was gone, I tried running again, it filled with water, but heard humming control panel noises for first time, then shuts itself off. Also, my handle needs replaced. Please let me know as soon as possible. Thanks in advance. David Weaver


Hi David\015\012\015\012The hum and all the noise that you have mentioned in your post states that the issue is with the pump and motor assembly. Please check the drain hose and try to clean the drain pump filter for any clogs, obstructions. Af ... Dishwashers

I have a 3 year old GLD6200 that gets used once per week While running it this morning I heard a sizzling sound, i turned around just in time to see the control panel flicker and go dark. This was followed by a little smoke & a very distinct motor-burning smell. My first though it that it's toast - suggestions?? In searching for info on line I must admit I am dismayed at the number of negative comments about product quality & customer service after a break-down. Hope thats the exception and not


... GE 24 in. GLD6200L Built-in Dishwasher

GE GSD6610GOOB not cycling properly. Our dishwasher is about 6 years old and has been nothing but trouble the past year or so. We've already paid too much money repairing it the first time, (it simply stopped working - the control panel was totally dead) and don't want to pay anymore. Current problem - the machine starts up and fills with water and it sounds like it's running OK, then it will just stop, sometimes for a couple of minutes sometimes longer. Then it will start up again - and


... GE 24 in. GSD6600G Built-In Dishwasher

Craftsman model 580.752020 electric pressure washer. First time I used it worked for about three minutes then the motor stopped. I cannot get it to start again. Plugged into a 15 amp gfi circuit which did not trip. The light on the plug is red as per instructions. Unit is beyond warrenty. What to do?


Turn off water and machine electrics.remove high pressure hose from front of machine, this may be tight if there is still pressure in the system.turn on water, when water comes out of machine hose outlet turn on machine. does the ma ... Electric Pressure Washers

Have a whirlpool gold dishwasher.The problem is that the clean lite on the control panel flashes not allowing the unit to work.I installed a new disposal and forgot to remove the plug for the dishwasher drain hose.When the flood happened I opened the door in order to stop the dishwasher.Now the unit will not work.The lite flashes 7 time ,then it pauses and flashes 7 times etc.Is there a reset procedure to run in order to get the unit to work or do I need to buy a new control panel?


HI,Can you please give the make and the model no. so that i can give you the manual.Waiting for your reply ... Dishwashers

First time it happen I notice that it started before it should with the timer, so started it without timer and it worked. Now its not going though circle again. Changing the program, and trying again, which did work first time but now it is not working.


1) you must test the timer is stuck with the contacts, you can try to clean it, tight loose wires, test wires open or break. Or doesnot replace complete TIMER. The timer contacts if you see the diagram is determinant control all operation machine of ... Hotpoint-Ariston LFT 228A 23 in Builtin Dishwasher

I have a mi-t-m pressure washer in the ca-series.The problem is the motor shuts down at times with out any reason. The first time I used it was on a house with a well supplied water. It worked fine,brought it home where I used it with no problem. It was used twice that first year. I then winterized it.The second year brought it out to the same house,I was using it for about a half hour when it just shut off with out any notice. I noticed there was back pressure in the engine when I tried to rest


Mi-t-m pressure washers have a Low Oil shutdown feature that turns off the motor, this is often causing similar problems on this kind of appliance.Have oil checked, if oil is fine , then the sensor that controls oil pressure and activate ... Pressure Washers

My Whirlpool GU2400XTP dishwasher keeps blowing the fuse. It sat up for 6months because the control panel went out and I couldn't afford to get a new one. Finally replaced the panel and the thermal fuse blew during the first wash cycle. I tried to put a 15AMP fuse in it's place to check it out before I bought a new thermal fuse and it too blew during the first cycle. Any ideas?


Are you replacing the wires along with the fuse? It is important to change the wires too as they are usually the cause for the fuse blowing. Be sure and get the fuse kit that includes the wires. \015\012\015\012Is your water too hot? Hot ... Whirlpool GU2400XTP Built-in Dishwasher

We have started experiencing a problem with our Kenmore Elite 655.15982 dishwasher. Each time we close the door, NoHeatDry lid would go on immediately. It would stay as is of would go flashing. If you touch any button, LockOn lid would go on. Then no other buttons would respond. And often both NoHeatDry and LockOn indicators would be flashing... We tried turning machine for an extended time on the fuse, etc. At times it would work for some time and then cycle get stuck again at the same p


These errors are due to a faulty control board and needs to be replaced. If its still underranty get it fixed before it expires as it is a costly repair to replace. ... Dishwashers

My dishwasher is brand new Model FDB1502RGS0. I used it for the first time today. It seemed to be cleaning for a very long time. It was up to 2 hours and I had to leave so I turned it off. How long should it take. That seems like an awfully long time. I kept waiting for the drying mode to start and it sounded like it kept filling up and emptying. Does this sound right? Please advise asap.


Most DW today take a minimum of 90 minutes. Run the hot water from the\015\012sink until it gets hot, then start the DW, this will shorted the first\015\012wash cycle. It is not uncommon for the DW to run 2hrs or more based\015\012upon the water temp ... Dishwashers

My touch pad has failed for the 3rd time. The first two times a technician installed a new one. This time I have ordered the part and am installing it myself and it didn't solve the problem.


... Haier ESD402 Stainless Steel 24 in Builtin Dishwasher

We have run our dish washer several times, however, the dishes are not getting cleaned. We first ran it on "normal wash." The second and third time we ran it on "pots and pans." Not only are the dishes not getting cleaned, but the soap is hardly getting dissolved. We use liquid dish soap too. I noticed this last time, at the end of the wash, the soap was getting built up on the front-right (when facing the machine) and had turned into a solid clump; almost like plaster. I don't have a manual so


First idea goto your local home depot they make a product called AFFRESH for front load washing machines and dishwashers run this tablet inside your dishwasher with no dishes on the inside on the hotest setting this usually takes out all build up wit ... Dishwashers

Have a new GE Profile dishwasher. The LED time display started at 62 the first time we used the machine. It keeps going up and is now at 108. Is it broken and how do we reset the time back to something more reasonable. We typically pre-wash the dishes anyway and it shouldn't have to take that long to clean....thanks!


Have you tried to turn the mains power to dishwasher off and back on again.\015\012\015\012It also possible the inlet water temperature is not at the recommended temperature so it is compensating for heating it to the desired temperature. ... GE 24 in. Profile PDW9280JSS Built-in Dishwasher

I have a Whirlpool Quiet Partner 3. It sat up for a few months because the control panel went out and it took a while to save up and order a new one. Now it blew the thermal fuse. I put a 15amp automotive fuse in it to try it, and it runs until it fills up and blows the fuse again. I am trying to figure out how to test the motor and the heating element to see if they are shorted. My local repair shop told me that they want to replace my new panel with their panel first, and that after that


A 15amp automotive fuse is rated for a 12VDC system in an automobile, not a 125VAC houshold electrical system in an appliance. I don't think your automotive fuse can handle the start current being drawn by the main wash pump as the dishwasher starts ... Dishwashers

Control Panel won't let me hit the start button. The dishwasher is a little over a year old and is used at most once a week. The blue light on the bottom right of the dishwasher seems to no longer light up. The control panel will let me select the wash, but the start button and time indicator does not light up. Not sure if this a real defect and if just a simple exchange of the front control panel will fix the problem? Already tried resetting the circuit breaker and that did not help. Than


... Dacor Epicure ED24 Stainless Steel Builtin Dishwasher

I have just moved into a home with the DS-603i and used it for the first time. I put it on the first load and seemed to go for way to long. so i opened it up and t washed the first load ok, but continued to make noises. It would make these noises even when draw opened. Turn on & off at power and it doesn't change the noises. The light on inside indicates rince, which i think is a F1 error code according to the manual online. Any tips on how to fix this?


The F1 error code indicated a leak problem. The noise that you hear is from the pump motor. There is a leak due to the top lid not sealed properly, so the water is shooting out during the wash cycle. It did not seal tightly because there are 2 actuat ... Fisher and Paykel 24 in. DS-603 Built-in Dishwasher

I just recently purchased a new fridgidare dishwasher and have tried it four times. the first three times i tried using a tablet and it didn't dissolve at all. this last time i used liquid and it all was piled up by the drain in the front left corner...is there something that i'm doing wrong? or is it a problem with the dishwasher...


Your water is not entering the dishwasher. Could be a kink in your water supply hose or the water supply is not fully on. Perhaps during installation the wires came loose from the water valve underneath.Check these things and report back. ... Frigidaire Dishwashers

Engine will not start,almost sounds like it is backfireing out of the carburater ,I cleaned out the old gass and put new in, cleaned gas lines,blew out carb with air two times, it ran for about 10 seconds the first time, and nothing the second time,----------What !


Pour a large amount of carb cleaner into the gas tank\015\012With choke on full, pull cord often to work carb cleaner into carb and then let it sit for a day or four.\015\012Your carb is dirty for sure.\015\012The venturi and jets a ... Honda Pressure Washer PSI 3000
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0659 seconds