Having problems with your Electrolux Frigidaire Professional Series 24 in. Built-In Dishwasher Dishwasher ?

Already replaced heating element, still not drying and not cleaning very well. Any suggestions would be very helpful. Thanks!


Answers :

If your system has hot air blow check the blower if you can locate in the machine.

For not cleaning, you have to check the inlet water pressure. Clean the strainer. Check all the the rubber parts that is getting attached, when you close the wash tray for the job.
Repair Help & Product Troubleshooting for Electrolux Frigidaire Professional Series 24 in. Built-In Dishwasher Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Already replaced heating element, still not drying and not cleaning very well. Any suggestions would be very helpful. Thanks!


If your system has hot air blow check the blower if you can locate in the machine.For not cleaning, you have to check the inlet water pressure. Clean the strainer. Check all the the rubber parts that is getting attached, when you close th ... Electrolux Frigidaire Professional Series 24 in. Built-In Dishwasher Dishwasher

Hi silverdragon, re the dishlex 302 not heating or drying Have replaced heating element but unfortunately still cold. If the control panel has not shorted which it hadn't before, do you have any suggestions. My hubby would rather wait before buying a new dishwasher, but I don't want to throw good money after bad. Is there anyone you can suggest who would be able to check out the circuit board to see if i have missed anything.


Hi\015\012\015\012Check the two thermostats located at the inside bottom front\015\012panel of the dishwasher, if any one of them goes bad it won't heat. Hope this\015\012helps...please post back for further assistance.\015\012\015\ ... Dishwashers

Blinking clean light on my Kenmore 665.17052400 7 times Did the "reboot" normal wash,heated dry sequence which made the machine work for a while. then it would go less times in between needing to be "rebooted", now it will not go through a cycle w/o the clean light blinking even following a reboot. what is my next step? I have heard that this means the microprocessor will need to be replaced. is it even worth it?


No its about a buck forty but im sure you could do it your self ... Dishwashers

Maytag MDB 8600 AWB dishwasher Wouldn''t start... just a Heated Dry light. Replaced (already broken) door handle with complete latch assembly. Still, Heated Dry flashes. Tried various suggested combos of 5 or 6 quick button pushes followed by Start. Only get a 50-=countdown that repeats endlessly. Sometimes alternates with the letter L. Once by luck I guess it went into Heavy Wash mode, or at least the diagnostic for it. Completed this fine, then back to the stubborn Heated Dry light.


... Maytag 24 in. MDB8600AW Jetclean II Built-in Dishwasher

We have a kenmore ultra wash dishwasher. i am unsure of the model number. i believe it was bought in 2001. the NO HEAT DRY button was blinking, so we replace some panel under the door. now the QUICK RINCE light is blinking. i tried the sequesce of WATER HEAT, NO HEAT DR, WATER HEAT, NO HEAT DRY, but that did not help. any other suggestions?? we have a family of 4, and it STINKS not having a dishwasher! litterally sometimes : )


... Kenmore 15129 Built-in Dishwasher

I have Whirlpool Quiet Partner III dishwasher, Model number GU2400XTPS3, Serial number FS1820245. I recently had the thermal fuse replaced by an authorized service repair person. My problem is that the dishwasher stops mid-cycle. I noticed that when I try to clean it in the normal cycle, the dishwasher stops with about 46 or 47 minutes remaining, and the green light flashes continuously. I have pressed the Normal and Heated Dry buttons, as well as the Sani Dry and HEated dry buttons to reset the


... Whirlpool GU2400XTP Built-in Dishwasher

I have Whirlpool Quiet Partner III dishwasher, Model number GU2400XTPS3, Serial number FS1820245. I recently had the thermal fuse replaced by an authorized service repair person. My problem is that the dishwasher stops mid-cycle. I noticed that when I try to clean it in the normal cycle, the dishwasher stops with about 46 or 47 minutes remaining, and the green light flashes continuously. I have pressed the Normal and Heated Dry buttons, as well as the Sani Dry and HEated dry buttons to res


... Whirlpool 24 in. ADG7540 Built-in Dishwasher

Kenmore ultra wash quiet guard dishwasher, the pots and pans and the normal wash button are blinking. The start and cancel and smart wash out tons have a faint light glowing. Thoughts? I tried the sequence of pressing heated dry, normal wash, heated dry, normal wash and that did nothing. I've flipped the breaker too. I was in process of taking it apart to clean filter, thinking that would help, but lost my manual and now I can't get that off to flea either:(. Sig


... Kenmore 24 in. 15689 Built-in Dishwasher

I have a Whirlpool DU1048 that started out with a blinking clean light. I reset the dishwasher by pressing the heated dry and normal buttons twice. That worked the clean light stopped blinking. The problem now is the dishwasher seem to be stuck in the wash cycle. I finally have to turn it off after over an hour washing. Is this possibly a heating element problem? is that user replaceable?


... Dishwashers

Cloudy Dishes My dishes have just recently started turning cloudy with white fllm. This has never happened before and the dishwasher is approximately two years old. There is no issues with hard water, and have used Jet Dry, have tried cleaning it with bleach and vinegar, and have used soap and no soap. Please give me suggestions as to why this would start occurring now. I took off the inside panel and it was full of all kinds of gunk which I since cleaned out. I would like to know how to avoid t


There is a new product out that filters the water going into your dishwasher. the film or cloudy white look is caused by hard water. this filter eliminates the problem and is very affordable. you can get it at dishwasherfilter.com. i was amazed how c ... Dishwashers

I have verified power to the Kenmore 15951 unit, but controls appear as if no power. I have tried hitting hi temp, heat dry, high temp, heat dry sequence like my reapir man suggested, to no avail. Not aware of any reset buttons. I have cleaned out the filter as well. Not sure where to go from here.....Rick


... Kenmore Dishwashers

Bosch dishwasher shx46b02uc has stopped drying. Per online comments, they seem to point to either a corroded wire or a bad heating element. We've replaced the heating element and all the wires looks fine. All other functions work - just not the heat. Open to suggestions.


Hello,Welcome to FixYa.Based on your description ... Bosch 24 in. SHU66C02 / SHU66C06 Built-in Dishwasher

My Hotpoint FDW60p complets its cycle but the 'Delicate' light flahes on completion and there is no heat during the cycle. I have replaced the heating element but it just the same. I also clean out some 'gunge' from the Air Break situated in the LH side panel but still no change. Any Suggestions? Stuart


Hello there Here is the diagram we talked about ... Hotpoint 24 in. FDW60 Free-standing Dishwasher

Dishwasher would not work and clean light would blink seven times. Asked an expert and they said to hit saniwash and heated dry two times. This work for a couple of times but now the dishwasher acts like there is no electrical power goimg to it. I tested the power with a voltmeter and there is power going to the circuit board.


Normally this happens when the dishwasher electronic control does not detect a water temperature increase during the main wash cycle. The issue could be in the heater element, the thermostat or the wiring that is connected to those or on the electro ... Dishwashers

Kenmore Ultra Wash Model 665.15801891 (Serial FJ3403697). This is in the USA. Unit will not run. Two lights are lit on the display panel and do not go off - 'Drying' and the #2 on 'Delay Hours'.rn I have turned off the power at the breaker box hoping it would reset. Once power is turned back on the Lock light comes on. I can clear that by pressing 'No Heat Dry' for 4 seconds but then the 2 lights mentioned above come on and do not go off. Any suggestions? Can you tell how old the unit is by t


Plase confirm if your model has the same front panel as the one shown in this manual.\015\012In that case try this sequence to reset the dis ... Kenmore 15899 Built-in Dishwasher

The inside of the dishwasher used to sparkle & clean the dishes very good, now the dishes look dirty & inside looks dull with a white film. I have tried cleaning filters & taking arms offs to check for blockage, making sure the Jet Dry dispenser is properly filled, the hose going to the dishwasher does not appear to be kinked, how would I check inside the dishwasher to see if it's kinked there? Do you have any other suggestions? please help!!!!


Hi, \012I have an older dishwasher also and recently mywife also complained about it not cleaning right... so me being the man I amtried in vain to clean the things... Bought new spray arms online and installedthem in minutes...now the thing works li ... Bosch 23 in. SHU33A Built-In Dishwasher

I have an E3 error message on m SMEG STX1 dishwasher. I've cleaned all pipes so am fairly sure that the heating element needs to be replaced. How do I access the heating element to test it? If there is a procedure for taking apart I would be very grateful indeed. Type 10031 model no 1471588673


Hi.E3 means that there is a problem with the heating system. The problem is either heating element or thermostat. The heating element in SMEG dishwashers is usually located underneath the appliance (in some model is at one side or at the ... Smeg 24 in. STX1-1 Free-standing Dishwasher

I have the Whirlpool DU 1100 dishwasher and the clean light kept blinking. I did the heated dry, normal combination and got it to run through the diagnostic check and sure enough it cleared the lights and appeared ready to run. When I would start it up again it would run the water and then get to the soad wash cycle and stop. No more lights it just stopped. I have been through the diagnostic process 3 times and still same problem. HELP


... Whirlpool Dishwashers

I have a Kenmore 665.1373 Ultra Wash dishwasher that will not work. In the past few weeks, it stopped mid-cycle, the the clean light began to flash. Sears sent out a technician who told us that the latch was not catching. He adjusted it, did something with a computer and the dishwasher worked for a couple of days. This time, it would not start a cycle, it would only show heated dry if you pushed the smart wash button and nothing if you press start. It looks like some of the lights are continuous


... Kenmore 24 in. 17482 / 17484 / 17489 Built-in Dishwasher

My accusense light keeps coming on and blinks continuously. I tried the heat-dry, normal sequence and it would reset to 2 minutes. After the 2 minutes cycle, the accusensor blinking would begin again. Then I tried holding the heat-dry button in for 5-seconds. This looked like it worked so we set a normal cycle without heat-dry. Äll looked good, but a few minutes in, the normal light was off, the accusensor was blinking again and the heated-dry was on again! Is the unit possessed? Other id


... Whirlpool GU2400XTP Built-in Dishwasher

"Runaway Dishwasher" Brand new model#FDB520RHS2 Frigedaire was installed today. It was on normal wash and did 8 washes and rinses. It wouldn't switch to the heat cycle. I hit the cancel button after 2 and half hours of washing and rinsing. The water emptied. I then opened the door and let it air dry...I am upset that it did this crazy thing. Do I have a lemon? What would you suggest???


Ask for warranty repair or replacement. ... Frigidaire PLD4375RFC Dishwasher

Our LG Model LDF6810ST Dishwasher (2 years old) does not heat water any more. Dishes do not get clean and do not get dry. I do not get an error code. I assume I need to replace the control board OR heater assembly. How do I determine how to solve the problem?


It cleans poorly ------\015\012\015\012\015\012\015\012\015\012Water-inlet valve\015\012\015\012Most cleaning problems are caused by the dishwasher not getting enough wash water, so the water-inlet valve is often to bl ... Dishwashers

Hello, Firstly, thank you for what you do, you help so many people and I know it takes time. I have a Bosch SHE44C06-UC Dishwasher. I fixed the E1 (Heating Circuit) error. First, before I found the writeup about the solder joint, I bougut a new heater and replaced it, ithe part included the element, flow switch and high temp sesor soall are new, then I fixed the solder and E1 went away and the cycle finsihes and the dishes are clean and dry. Still I check the error codes and still have


... Dishwashers

My wife opened door during cycle. When she closed door it would no longer run. Looking at problems and recomendations on similar models, I replaced the board. Did not fix the problem. I have checked the fuse and the door switches for continuity and all seem ok. The only lights on the panel that come on are: under cycle- Pots & Pans, Light. Under Options - Heated dry. No other lights work and the dishwasher does not operate.


Hi,\015\012\015\012First off, sorry to hear that you replaced the control board for nothing..in hindsight. So if I understand what you're saying is this, You cannot select any cycles and the unit won't start...because the start button is ... Dishwashers

F&P dishdrawer problem: I don't think the heater is working to heat water and dry, as dishes not very clean now and quite wet when cycle finished. The lights don't work anymore so have not had a fault code. How do you replace the heater element? Thank you.


First, open the door and look into \015\012 the tub and locate the heating element (if it is covered, remove \015\012 the lower dish rack and cover). The heating element has two terminals \015\012 which ex ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1512 seconds