Having problems with your Electrolux Frigidaire Professional Series 24 in. Built-In Dishwasher Dishwasher ?

The power to my dish wash is on but no water it just want start cleaning


Answers :

Hi.... you have a bad control board

Thanks
Repair Help & Product Troubleshooting for Electrolux Frigidaire Professional Series 24 in. Built-In Dishwasher Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

The power to my dish wash is on but no water it just want start cleaning


Hi.... you have a bad control boardThanks ... Electrolux Frigidaire Professional Series 24 in. Built-In Dishwasher Dishwasher

Westinghouse Virtuoso 922 dishwasher. Wash cycle completes, but water does not drain out. If I let the cycle continue, after a delay the rinse cycle starts, but of course no clean water is pumped in so the dishes are "rinsed" in the dirty wash water. The wash cycle itself is successful with water pumping all around the washer if I open the door mid-cycle. I have removed and cleaned all filters which were correctly fitted so I am confident there is no foreign matter inside pump. When the water sh


... Dishwashers

Upon selecting a wash cycle and closing the door the machine starts normally (heating water stage) but never clicks to allow water in and wash the dishes. Fails to advance to the wash cycle and just runs without doing dishes. There was water in the bottom after the last wash, filters are clean?


... Bosch SHV46C03 Built-in Dishwasher

Miel dishwasher G865 Was not cleaning dishes properly so I put some Power 1 which is similer to CLR, started a wash cycle then partly into it I switch it to rinse. Now it still the same and the water does not drain comepletely.


Sorry to read about your problem, I hope this helps you out.you may have a clogged pump, or a defective pump.I suggest you contact a service company.I tried to help you. Please help me and Rate/Vote on my response. ... Miele 24 in. G865 Built-in Dishwasher

I have a single draw Fisher and Paykel dishwasher. I stupidly put washing up liquid in the dishwasher which resulted in a F1 problem. Water started leaking under the draw and onto my floor. I turned the dishwasher off at the power point and have cleaned up the leak. Have I damaged my dish washer? How do I fix it?


Ok , F1 means your flood switch has activated, which is underneath the drawer. now they show the F1 fault because of 2 reasons.1st there is still water underneath drawer causing switch to activate. 2nd your activator board which has the flood switch ... Fisher and Paykel 23 in. DD-603 Built-in Dishwasher

I have the Whirlpool Quiet Partner 1 the wash cycle starts and about 20 Min.'s into it the clean light starts flashing or the the start light, one or the other each time and it wont dry the dish's anymore we have already replaced the panel once and it has always popped when it is filling with water or changing cycles. HELP!!!! I hate washing dish's and I am beginning to hate all Whirlpool Appliances.


If the clean light blinks 7 times thats you heating circuit. Test the heater with an ohm meeting to see if it has open. If so order the heater kit and it comes with the control board. ... Whirlpool GU2400XTP Built-in Dishwasher

KitchenAid KUDL03IVWHO Machine seems to stop after the initial water fill. There is power to the machine, the door latch circuity is working, all the buttons on the control pad light up. After selecting any of the wash cycles and pressing start, the washing light illuminates and the machine fills normally to the point where the fill valve stops the inflow of water. At this point the machine stalls, it does not start the cleaning process. I can press cancel and the machine drains normally. I e


Hi,\015\012\015\012You have got to the correct resolution. This is a circuit or most commonly called the board problem. Please find the bellow mentioned link which will help you to get one compatible for your washer.\015\012\0 ... Dishwashers

Inglis MOD#IPU58460 Dishes not cleaned properly...thought that enough water was not being filled into tub because more water added manually and washes great! I checked inlet water valve operation and lines for possible lime buildup and timed "fill" time. All was good and time right to spec! Water level after fill is just to bottom of mesh screens. Under further trouble shooting I held door open slightly while holding door switch closed to observe wash cycle and found as pump starts water shoots


The sprayer arm may be clogged with debris.Here's a step-by-step troubleshooting guide. ... Dishwashers

Maytag Model MDB7160AWW S/N 10337613WQ Symptons: Fills with water OK, shuts off water OK, does not start any cycle, or drain. After a power off/power on reset, problem remains. Flashes CLEAN & LIGHT WASH. My understanding is this is an error condition for low motor current, which makes sense as the motor never starts. I know both door switches are good (I checked them with a DVM) and both engage when the door is closed. Tripping the water float switch opens the valve and water fills the tub


... Dishwashers

I have a Bosch Dishwasher Model # SHU43C that is not washing properly. Some dishes are not being cleaned if we don't pre-scrub or rinse. There are no error codes on the panel. During the cycle I hear the pump motor starting and stopping repeatedly on about 1 second intervals. I suspect it may be starved for inlet water. I checked the inlet water line and it is clear. We use well water that occassionally has some iron sediment in it and it plugged the inlet water screen for our washing mach


Hi,\015\012It is very possible that the screen is plugged...most inlet valves have a screen just like your washer does. I would at least remove the hose/pipe and check the flow...and check for a screen. \015\012Also the solenoid can get j ... Bosch 24 in. SHU43 Built-in Dishwasher

My ge dishwasher fills with water just fine,cycle starts, but soon after, starts draining some of the water while washing. It then seems like there is not enough water in there to get the dishes clean. Why is it doing this?


... GE PDW8680NSS Built-in Dishwasher

I have frigidaire dishwasher,starts cycle,can hear water entering dishwasher,checked level of water,does not get to 1",machine starts washing by the sound of motor, but dishes are not clean,water drains machine turns of,cycle complete.what do you think.


Depending on your dishwasher, it fills either by a timer or by a water probe or float. I will assume its a timer as a probe or float wouldnt exhibit this behaviour. I would say you have a restriction in your water supply line. Check your valves, an ... Frigidaire Dishwashers

Dishes not clean after running. Dishes and glasses have a white residue on them after drying. Water is turned on and seems to ok. When I open the washer after the wash cycle starts there are several inches of water in the washer and the jets seem to be functioning. Thanks for your advise.


Hi If you are noticing that the dishes are not clean, then there are a few things to check for. Check the soap powder if it's kept in a dry environment. Also try replacing the powder with something like a gel or liqu ... Bosch SHU9925UC Built-in Dishwasher

Model number 66515632000 Kenmore Ultra wash with quite guard about 8 years old Washer stopped near end of rinse cylce, dishes look clean, water in washer did not drain and looks clean. All attempts to restart washer, or hit drain etc result in attempt to start and then it stops. sounds like trying to start a car with a very weak battery.


Unfortunately it sounds like you have one of two possibilities. A) You have something like a piece of glass or food ect. that has worked its way down into your pump and is tying up the impeller or pump as its trying to start. -To op ... Dishwashers

Bosch diswasher less than 1 yr old SHE4Apo6UC/05. At start of wash, tub fills with water then cycle goes from ACTIVE to CLEAN within a couple of minutes. Dishes don't get cleaned and water doesn't drain from tub.


I have the same problem. ... Dishwashers

My Whirlpool ADG 6340 built in dish washer seems to start ok, fills with water and I believe it starts the wash cycle but after about ten munutes it stops and all the water will not drain away. I have cleaned all filters and hoses but still the same results. Any suggestions welcome.


... Dishwashers

Ultra Wash Hi, When I got up this morning, I noticed the dishes were still dirty and dry??  The soap dispenser had popped open but that was about it.  I had some work done on it because it wasn't cleaning the dishes properly about a year ago and they replaced the motor.  While cleaning the kitchen last night, I heard it come on, but now that I think about it, I never actually heard the water start sloshing around. I don't have the owner's manual - I bought this house 3 years ago and I think the


Sounds like your not getting water to it. Turn on and let run for a few minutes then open door and check to see if you have water in it. If not check to be sure water to it is turned on. Check float in front corner of dishwasher to see if mo ... Kenmore 24 in. 15689 Built-in Dishwasher

Hi, The machine will not complete a cycle. I think it may have started when the power was turned off at the mains during a cycle. Symptoms are : - You can turn machine on, select a program, press start button, close door, machine appears to begin cycle as normal, water seems to load, then 2 minutes later drains, and 1 minute or so after that the machine beeps 3 times to indicate cycle is finished. Dishwasher tablet door never opens, dishes not cleaned. Have tried : - cleaning filters; - turn


It is likely the dishwasher is locked in some diagnostic program.\015\012If you provide the dishwasher model no. then I can try to find out the keys you need to press to get it out from it. ... Whirlpool Dishwashers

I have a Fisher & Paykel 913T soft touch dishwasher. On all types of washes when the wash cycle starts there is no 230 volts on the element & after 5 minutes the wash cycle finishes & then goes onto to the next cycle. None of the wash or rinse cycles heat the water but on the dry cycle their is 230 volts onto the element & dries the dishes OK. Is my problem the power supply PCB or could it be the Controller PCB? Does the 230 volts to the element on dry cycle come from the same cicuit on the po


Have you considered the possibility the water temperature sensor may be faulty.\015\012\015\012If the controller is getting false water temp reading then it may never turn the heater on.\015\012\015\012Generally with FP dishwa ... Dishwashers

I have a Bosch dishwasher model #SHU3032UC/U12 It is not pulling water from the water pipe to wash the dishes the motor wants to go thru cycles. It starts to pull the water by the sounds from the sink but no water gets into the dishwasher.


Hello. When no water is entering the dishwasher, there are two parts to check. \015\012Water-inlet valve\015\012\015\012\015\012\015\012\015\012\015\012\015\012\015\012The water-inlet valve lets water enter the machine. If this ... Bosch Dishwashers

GE TRITON dish washer. Utensils are stained after wash. I tried all that suggested solutions like cleaning with white vinegar, make sure hot water flows before it starts. I donot think we have hard water problem and also tried Jet dry rinsing. Nothing is working still i see utensils soap stains and not completely rinsed. I am desperately looking for an answer. I am thinking of is there a way i can test whether the middle tower is really opening up to spray water or not. It might be something els


Hi,The scum, film and white\012residue problems have started since the reduction of\012phosphates in dishwasher detergents.Here is a tip that\012will help you to solve the problem of films, residue, and scu ... Maytag Dishwasher

My bottom dish washer was draining the water on the top dishwasher and there is always water left over on the top.I remove the pipes and put CLR to clean up drain.Start both dishwasher on rinse cycle ( 12 min cycle) then at 10 min.they start blinking with a No tap (may be water ) sign on it. I run the cycle again now a F1 sign coming with a tool sign.And both dishwasher going crazy ,it turn on by itself even I powered them off.


Hi\015\012\015\012\015\012Thanks for using FixYa. F1\015\012error means that the flood switch has been activated. You'll need to reset it by poweri ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

The dishes are not clean when we run the wash cycle. It looks like the water flow from the top sprayer is NOT working. The door, when we open it, has undesolved soap stuck in globs on the top of the door. The top dishes are not clean and some of the botom dishes are not clean. We've run some clear washes to see if we can find the problem. The water flow looks suspect. Is it in the electronics or in the water mechanics. I called the repair guy who ususally comes out and says buy a new one! The re


Hi, \012I have an older dishwasher also and recently my wife alsocomplained about it not cleaning right... so me being the man I am tried invain to clean the things... Bought new spray arms online and installed them inminutes...now the thing works li ... LG 24 in. LDS 5811 Built-in Dishwasher

Our GE Profile (Quiet Power 6) dishwasher is having trouble cleaning our dishes. The top shelf rarely gets cleaned and the bottom is questionable. It used to work fine. We always use Cascade powder detergent on a normal wash cycle. We have hard water. Any advice would be appreciated. I took apart the washer looking for an obstruction but none existed.


The obstruction can be external to the unit. Check the drain at EACH connection working backward from the sink connection all the way to the motor pump outlet hole. Do not forget to dis-assemble the Air-Gap (if installed) and to check the inside of ... GE 24 in. Profile PDW9880JSS Built-in Dishwasher

When my dishwasher completes its cycle, there is powdered detergent left in the dispenser and the dishes aren't as clean as they use to be. This started happening after I ran a HI TEMP WASH with a SANI RINSE cycle. I'm thinking that either the detergent dispenser door is opening late or the water is not getting hot enough. To check the dispenser door, I left the door open and just poured powder into the dispenser compartment. This did not improve the cleaning.


Hi\015\012 \015\012Dishwashers use Bi-Metal strip to allow the dispenser to open/close. This strip when heat up causes the soap door spring to open up the dispenser. If this strip is not heated doesn't allo ... Kenmore 16372 / 16374 / 16379 Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.2164 seconds