Having problems with your EuroTech 24 in. EDW194E Built-in Dishwasher ?

Dishwasher is new and will not come on and run. Turn dishwasher on and set program, shut door and nothing happens.


Answers :

Repair Help & Product Troubleshooting for EuroTech 24 in. EDW194E Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Dishwasher is new and will not come on and run. Turn dishwasher on and set program, shut door and nothing happens.


... EuroTech 24 in. EDW194E Built-in Dishwasher

Belling BE601 I Recently came into posession of a Belling BE601 Dishwasher, no Manual as is second hand. The condition of the dishwasher is as good as new, but when the door is closed after setting the program, nothing happens, it will not start up. I have checked the door switch and it is working ok, any ideas ?


Reset the display to -.if there's a number there it's the length of time later it will start at.both the start and the program have to be selected together..........but you also have to reset it after the last program ... Dishwashers

I have a bosch SHU8815UC dishwasher. It was already installed when i moved into my apartment - so I'm unsure of the age. The dishwasher isn't functioning. When I open the door, the "Clean" light and the PowerScrub button are red. When i close the door, the light go off but nothing happens. One time I closed the door, it started to rev up but would shut off and beep three times after about 1 min. No water comes out. Any ideas? Thanks! June


... Dishwashers

I have a smeg dishwasher DI612CA9, when you set the program and shut the door after about 5 seconds it beeps 3 times and then does nothing, i emptied excess water from the bottom but has had no affect


... Smeg Dishwashers

Zanussi zdt6053 in built dishwasher not starting. When pressing the control panel on/off button the 65 deg normal wash light comes on. When pressing the program selection button nothing happens. When closing the door the machine does not start up. Is there a fault in the control panel circuit board? Would water pressure prevent the machine from operating?


... Zanussi 23 in. ZDi6053SX Built-in Dishwasher

I have a Whirlpool G2P DWI dishwasher and when I start the program the light comes on to say it's ready, but when I close the door nothing happens. I have tried turning it off and on again and also cleaned the filter but this hasn't done anything. Please help


HiThanks for using FixYa. To start with press and hold Air Dry for 5 seconds until the light turns off. If still the issue is not resolved then it means that the control has gone bad and needs to be replaced. Please do accept ... Dishwashers

I have just moved into a new house with an Asko Dishwasher. It is not working. I program it, the icon for the cycle I have chosen lights up in red, I press start, that lights up in red, the water runs in for about 30 seconds and then nothing more happens. This happens on every wash cycle that I attempt to use. It does not appear to be on time delay as that icon does not light up. Also I have left it for a number of hours after I have tried to start it and still nothing happens. I would appreciat


... Asko Dishwashers

I have a KitchenAid Model KUDP01FLBT5. After I push one of the clean buttons, and the start button and close it, nothing happens. The indicator lights for the buttons come on as you push them. When this first started, you would ahve to open and close the door and re-set the buttons (not sure if that button re-setting had anything to do with it) up to 20 or 30 times, and it would eventually come on. Now it won't anymore. Help!


Hi\015\012\015\012Thanks for using FixYa. To\015\012resolve this you will have to reset the console. Do this by closing the door\015\012and press these buttons in sequence...\015\012\015\012 ... KitchenAid 24 in. KUDP01FL Built-in Dishwasher

Hi there. I have a Matsui MF145 slimline dishwasher and having a problem. When I press the on/off button I would usually then press the program indicator button (usually the first indicator - pans) and close the door and the dishwasher would start. Currently i press the on/off button and try to press the program indicator button and the on/off button flashes and there is a continuos beeping sound....and nothing more happens. Do you know what the problem is?


Try to clean the unit, ofetn when the machine is dirty, some sensors are fooled thinking there's some problem. be sure there's no jam on mechanical parts. ... Dishwashers

Hi. I have a Danby DDW396W countertop dishwasher brand new yesterday. We unpacked it, installed it onto taps, loaded it with dishes, and turned it on. That's where everything went wrong. When you turn it on, the display shows P2 and when you press the program button to change it, nothing happens. When you push the start button, nothing happens. What am I doing wrong? I know I'm missing something simple, but what? Please help. Katherine


Hello there and thank you for choosing fixyaThe p-2 code is a wash cycle that is the normal cycle for this unit please see below.Press the program button until the desiredprogram code appears in the display window.The ... Danby Dishwashers

Good day after the power is turned on to my brand new kudc03fvss dishwasher, nothing happens. have made sure that the power supply is ok and that the door is properly closed. there is 115 volts at the circuit board inside but nothing happens. no lights, no response to switch etc. just dead. need some advice


You said your getting 115 volts and that is across the power wire and its neutral not a power and ground.. i had a case like this last week and when i got there the unit had power if tested from black to ground but not from black and the white neutra ... Dishwashers

I just bought this house with this dishwasher built in. I have pushed the door shut, pressed the heat dry button to lock the door and pressed the start button. Nothing happens. Now I can't even get the lights on front to turn off. The lock button flashes as though the door is open, but its not as far as I can tell. I have to press the latch in to open the door. I'd like to use it... any ideas. Its a Kenmore Elite model # 665 17052 402. Thank You


... Kenmore 24 in. 17052 / 17054 / 17059 Built-in Dishwasher

I have a Magtag dishwasher, model #MDB6650AWQ thats not running. I check the power supply all the way up to the door latch and it shows that there's power there. However the circuit panel not lighting up and nothing happens when you push the normal wash cycle or any of the other buttons. I believe the problems is electrical in the door latch handle. Is there any way to check the solenoids which are attached to the door handle before I order a new door latch.


I have the same problem with mine. It is 3 1/2 years old. The repair man was just here and said it is the control panel. It will cost $171.85 for the part and then $53.85 today for his visit and then a return visit when the part is in.\015\0 ... Maytag Dishwashers

There is a pool at the bootom of my dishwasher when the wash cycle is completed. When doing "Rinse Only", I could hear something come on immediately following the rinse but nothing seemed to happen. I pulled the Dishwasher out and the drain tube is set up so that it immediately goes upward a few feet before it eventualy goes back down to the drain. I noticed that there is water in the tube right next to the Dishwasher before it makes that climb. I'm wondering what all this means...


Http://frigidaireservicetips.com/pdfs/486_5.pdf\015\012\015\012\015\012\015\012 ... GE GLD5800L Dishwasher

Sears Kenmore dishwasher 665-15632000 dishwasher will not turn on. Little green lights never come on. Nothing happens--dead silence. How to fix or manual as to how to fix or how to take out dishwasher--remove front door, etc.


... Kenmore Dishwashers

Bosch shu8806 Hello, I aquired a shu8806 recently and it doesn't work. It has power and water. I push wash cycle, indicator light comes on, shut door and nothing happens.  So the door switch seemed like a good place to start. Since I am an electrician I thought I would give it a shot. When plugged in, the wire from the motor is 120V but when jumpered to the neutral(common on the door switch), motor doesn't operate. Although, I have heard the motor turn over momentarialy when trying to run unit e


The pump may be clogged, or the motor start capacitor may be bad or some units have a fill switch wired inline with the motor so it won't start unless the unit is full ... Bosch 23 in. SHU 8805 Built-in Dishwasher

My Bosch dishwasher is 8 years old and always worked well.. About a year or two ago the dishes started coming out dirtier than when they were put in, frequently encrusted with dirt and shredded dirt which looked like finelly shredded vegetable discards from the garbage disposal. The first set of repairmen sold me a new pump. The next people told me there was nothing wrong with it. The third repairman told me that I have to set the water heater on very High (for $98.00)


I do know this on most dishwashers water temp must be @ least 120 and not exced 150 degree`s before they will go into a complete wash cycle ... Dishwashers

Took these from a previous page, because this is what is happening to our lab Miele Platinum G892/G892 SC. Can you tell me what the problem is and how to fix it? Thanks. intake /drain light is flashing,full water- Guest Feb 26, 2009- I have same problem - open the door and there is water at the bottom of the dishwasher - when I restart program, the water drains out fine. Also, I have great water pressure coming into the dishwasher, filters are clean, etc. I am suspecting it is a circula


If there is verified power at the pump motor - your timer is defective.Thanks For using Fixya!! ... Dishwashers

The Dishwasher PLD2850RDC2 will not start. The CL flashes, the type of cycle pressed on the key pad does respond, but nothing happens when START is pressed. Steps taken: -Door is clicked shut -Power breaker has been turned off and back on -All dishwasher moving parts have been moved by hand to ensure no obstructions are in the way. Best guess is the key pad is just non responsive. I hope there is an easy solution. Thank you.


... Frigidaire 24 in. PLD2850 Built-in Dishwasher

Dishwasher is Amana ADB 2500 AWB. Door handle broke. Installed a new Latch Assy. (many buttons were pushed during process) Now .. door latches good. But when start is pushed, nothing happens. (all the cycles and options will light up) Is there a reset button? Could I have connected a wire incorrectly?


... Dishwashers

New World DW60 dishwasher not working originally had E4 fault Power comes into the PCB the switches and led's light up but nothing happens. After about 5 mins there is a short beep. Does not show any error codes, New World sent a replacement PCB which made no difference except now have no error code. Circ pump, inlet valve, heater, drain pump checked independantly all worked.


I f you have warranty on this please call them, you have a defective\015\012D/W.Unless there is no charge for repairs ,don't spend a dollar on what\015\012is going to be a on going problem ahead.To explain how to fix this is\015\012what the manufactu ... Dishwashers

Maytag Dishwasher Model MDB4100AWQ When I start the Light Wash Cycle: Washer fills with water, heater comes on (I checked it with a volt meter--120 volts), timer runs, motor never runs, before the timer gets to "rinse" the heating delay light on the door comes on and the timer stops. The heater is still on (120volts) nothing further happens it just boils away on the water in the washer. Note: If I manually forward the timer to "rinse" the motor will kick in and run but does not pump out w


Most common d/w power is 120 volts, check for 120 volts with a  ... Dishwashers

The power is going to the dishwasher. The on off buttons work. No error codes. The salt light is lite (has been for 5 years) but now I get zero response when shutting the door (after selecting any of the 6 run options). There is no noise, no water, nothing happens. How do I repair this dishwasher so that it will run again?


Door switch failure. This will shut down all other start options. Inspect and possible replacement. See if you can activate it with something with door open. Give it a good close look... ... Dishwashers

Frigidaire Dishwasher Hi, I have installed a new model GLD2250RDC0 Frigidaire dishwasher and it will not start. Power and water supply is connected. When I push the cycle button for Normal the light comes on but when I push Start nothing happens except the "hi-temp wash" and "no heat dry" lights flash. I assume this is some kind of troubleshooting code but the manual does not cover this and I am in Honduras so service is non existent. Any ideas? By the way, I was a builder in the States for 25 y


... Frigidaire 24 in. GLD2162RDC Stainless Steel Built-in Dishwasher

Indesit d63 dishwasher, door locked shut. took top off+got to latch, the plastic catch wouldn't pull out of the latch. undid it all, all seems unbroken but cannot seem to arrange the latch so that it will allow the plastic catch to come out when levered. also not sure if the handle is supposed to click the switch to another position, or just tweak the switch as it opens the door. is a new latch supplied with the switch ?


Check with whoever you order the latch from, usually parts are individual for electrical parts and never assume that the screw or washer will come with new one, save every piece. ... Indesit 24 in. D63 Free-standing Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.2115 seconds