Having problems with your Fagor LFA-013 Stainless Steel Built-in Dishwasher ?

Hi, my new FAGOR 2LF-013S has no problem fortunately, but i have questions. is it possible i connect the water hose to hot water mains ;if ok; does it lead to power consumption reduction, or any other changes in performances? thanks


Answers :

Some fagors have a built in water heater (not all) your manual should say so , even so I allways connect my machines to hot supply as yes it's less expensive to use domestic heater for water , the heater inside (if equipped) machine just boosts the temp for cleaner dishes
Repair Help & Product Troubleshooting for Fagor LFA-013 Stainless Steel Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Hi, my new FAGOR 2LF-013S has no problem fortunately, but i have questions. is it possible i connect the water hose to hot water mains ;if ok; does it lead to power consumption reduction, or any other changes in performances? thanks


Some fagors have a built in water heater (not all) your manual should say so , even so I allways connect my machines to hot supply as yes it's less expensive to use domestic heater for water , the heater inside (if equi ... Fagor LFA-013 Stainless Steel Built-in Dishwasher

FDB750RCC1 When I start the DW, the motor hums loud then soft then loud then soft...if I advance the dial some sections of the cycle nothing will be running and others the motor is on, but no water is getting into the unit. I just replaced the inlet valve and solenoid and that didn't change anything. I can see water in the recirculating pipe running up the unit, but it will just try to make it up and fall back down. Not sure how to proceed...my thoughts would lead me to the main motor, but


Can you hear the water solenoid click when it calls for water? If so, check that the water source valve is on and water comes out of the valve. Check the entry hose for kinks. Remove everything under the lower arm down to the deck keeping track ... Frigidaire 24 in. FDB750RCC Stainless Steel Built-in Dishwasher

No water is running to my dishwasher. I ran the diagnostic test sequence and that didn't fix the problem. Nothing else has changed and I checked the pipes leading to the dishwasher and everything seems fine


Check to make sure the overfill float in the bottom of the washer could move up and down freely. It is a small white disc float. If it is stuck in the up position your washer won't fill up. I hope this helps. ... Whirlpool DU1055XTS Built-in Dishwasher

Obtained this haier hdp18pa portable dishwasher, thought I would give it a try. The unit will not fill with water, turn the power on you can hear the motor or the pump running but no water comes in. THe 4 display lights flash and beep a series of times and then stop only to repeat the sound off in a every few second sequence. I have tried the remedies offered online, tilting the unit does not seem to work for me on this one. I changed out the water inlet valve but nothing changed and I got the s


HiYou need to clean the filter that is in the tube that gets water in the dishwasherin case you can not find it pls ask me to send you a diagram ... Haier HDP18PA Stainless Steel Free-Standing Dishwasher

The dishwasher fills with water to the level of the heating coil, when the wash clyce starts it pumps water but not enough to turn either spray bars. I have changed the chopper and wash impeller, cleaned the filters and float assy. Changed all the seals but it will not turn the sprayers. Help??


It sounds like a serious loss of pressure. I have a couple of question for you that will help me assist you.Can you get me the complete model number from the tag just inside the door?Does any water leak on the floo ... Kenmore 16632 Built-in Dishwasher

Hello, We have a Candy Diswater that is just arround 2 years old. When it starts it takes water and then you hear the washer going into loop. It tries to do something els but doesn't seem so. If you open the door you can see water inside but no progress or heating. If you also try to change the program it doesn't change as well. Before it got to this point sometimes we used to unplug the power and tunr it off and then ON and then it works. However, now this procedure is not working an


Quite possibly could be the timer and could also be the main control board as well. Sometimes unpluging it will help for short times but if a serious problem persists it will only be a temp fix... ... Dishwashers

Zanussi DW908 dishwasher will not fill with water, when filled manually completes cycle untill fill time again. when filled continues on until water needed again. Only cold supply to machine. Water coming to valve, removed valve and freed it up as it was stuck, water flows through the valve when disconected from the dishwasher at filler pipe which leads up the side of washing chamber. When all connected up water will not enter the dishwasher. I,m beaten as I cannot access this area without maj


\012\012Hi,\012Here\012is a tip that will help you to find out why water will not come into\012the dishwasher... Dishwasher Trouble ... Zanussi Dishwashers

I changed my water control valve, thinking my dishwasher was not getting water, however, if I put water in the basin, dishwasher pumps the water out, however, it sounds like the dishwasher stays stuck in the drain mode, pump just continues to run?


Hi,\015\012\015\012There is a simple explanation for this - water is leaking into the bottom of your dishwasher under the washing compartment. This has caused the float to rise and trip the switch which activates the Aqua-Stop / anti-floo ... Bosch SHU9915UC Dishwasher

My dishwasher AEG favorit 525 worked perfectly but has been out of action for over a year. yesterday when I tried to use it, the on button is on continuously and no water is pumped into the machine. yes the water is on. the program button is also rotating as the programs change but no water comes in and I am not sure whether it will pump water out as I have not yet got there. please help.


Hi\015\012\015\012The issue seems to with the pressure switch that is bad and\015\012so won't allow the water to flow inside the unit. You can take it apart to\015\012check this. Hope this helps...please post back for further assistance. ... Dishwashers

Model # gsd3320c04bb. I am getting water to the inlet valve. I tried changing the inlet valve but still no water goes thru it. I am getting 22 V AC at the connector when operating. The only water that is circulating in the dishwasher is the water that is remaining in the pump system. Any ideas as to what is preventing the inlet valve from operating?


Sounds like you need to replace the mixing valve which is where your incoming water lines connect to the back of the washer. ... GE 24 in. GSD3320 Built-in Dishwasher

My dishwasher was moved for kitchen rennovations. When hooked back up again it would not fill up. It will run through a cycle but no water enters. If I squeeze the rubber hose that leads from the electronic valve to the tub it gets hot indicating that I am forcing hot water through the line. If I pour water into the tub it will wash the dishes but at the final 6 minute point it will go no further, I assume because it is not getting rinse water.


Hello,\015\012Make sure that a wire did not get bumped off of the soleniod valve. It sits usually on the bottom front left hand corner of the dishwasher.\015\012If the wires are both on the valve then the valve may need ot be replaced... ... Dishwashers

Hi :) We have a Bosch slimline dishwasher type SRS56A02 GB/08 - it doesn't draw in water - the timer counts down but nothing happens. We checked these pages and cleaned the filters on the inlet water line but no change :( I saw that it might be the inlet water valve - is this easy to get to - do we need to take off panels? if so, is there a manual available please? Over the past week or so it had got noiser - it was at its quietest while the water was draining out of the machine.


... Dishwashers

Dishwasher does not fill with water when started. Problem began slowly with dishes not rinsing completely. Overfill float appears to work properly. Water fills pipe leading to fill solenoid but does n


I am almost certain that your problem is the fill solenoid.If it does not work, there will be no water entering your machine.I would either remove it and test it or just replace it at this point.Tim ... Dishwashers

Water not flowing into dishwasher. I've taken door off, detached 1 lead to the solinoid. It shows 987 ohms resistance, can feel AC hum when 110v put into the coil - but no water flows (water attached). Where do I go from here?


Hello,\015\012\015\012Welcome to FixYa.\015\012\015\012Based on your post and the findings of the valve resistance of 987ohms, ( normal is 1Kohms ) it sounds well within acceptable range, however the valve can sti ... Bosch 24 in. SMU70 Built-in Dishwasher

Dishwasher is 16 months old. Recently, it won't get tea stains from spoons or cups and there is a white film on plastics. I have run unit once with vinegar. I tried using less detergent and no change (Cascade Complete). (Neighbors using same detergnet on different machine with no problems so it's not the water.) I always select High water temp and air dry on normanl wash. My hunch is that the motor is going bad and therefore it is not pushing the water with enough force.


Hello, there are a few thinks to check on the dishwasher. Circulation, drainage - no backflow back into tub, and water temp. If all three are good, then you have hard water. \015\0121. circulation - These MDB models are very good with water circul ... Maytag MDBH985AWB / MDBH985AWS 24 in. Built-in Dishwasher

Hello, I had a problem with my Bosch dishwasher not washing properly. I have fixed burnt out wires, replaced the water inlet valve, AND tested with a new control module. Nothing is helping. When I start the cycle, it completes the initial drain and water does flow into the unit for about a minute, maybe a minute and a half. I can hear the clicking of cycle changes but it is not washing. Eventually it will drain the inch or so of water in the bottom, but it never washes. Any help???


Hi,\015\012\015\012Welcome to Fixya.\015\012\015\012Can you hear the wash motor humming ? I`ve got a "pdf" I can send you regarding this if you want to contact me at ... Bosch SHU9925UC Built-in Dishwasher

I've got a hotpoint bf168 dishwasher,been working fine until y'day when nothing washed, realised there was no water coming into it. Change water inlet pipe but still nothing, I can hear water going thru the pipe but then just seems to empty itself. Any ideas guys .


Hmmm.... could be the controler. or a stuck valve... have you tried to reset it? turn off power and turn it back on... ... Hotpoint 23 in. BFI68 Built-in Dishwasher

Can you change the temp of the water coming in the dishwasher? Other than the temp from the hot water line. The temp to the sink is very hot but when you open the dish washer the water just seems very warm. I didn't know is there a temp setting for the dishwasher?


THE WATER LINE TO THE DISHWASHER SHOULD BE FROM SAME HOT WATER LINE TO THE SINK. RUN THE HOT WATER IN THE SINK UNTIL HOT THEN TURN ON DISK WASHER AND CHECK THAT THE TEMP IS CLOSE TO SAME TEMP. HAVE SEEN COLD WATER LINE USED. YOU SHOULD BE ABLE TO SEE ... Samsung DMR78AHS Builtin Dishwasher

It does not seem that my dishwasher arms are putting out enough water pressure. the top arm does not spin at all the water just spits out of them. my water pressure has not changed in the house and it does this with nothing loaded in it.


Sounds like the water pump is clogged,remove hose and **** out with shop vac,thanks-mike ... Kenmore Dishwashers

My Whirlpool Gold Series 980 dishwater no longer fills up with enough water to drive the washing arms, so the dishes do not come out clean. I cleaned the filter on the water intake valve (which was really clogged) and it still did the same thing. Replaced the inlet valve and still no change. The water does not reach the level of the overfill float switch, so that’s not it. Its been working fine for 4-5 years, what else could it be? Thank you.


I hve provided u with all details .read it carefully .it has all the resolutions for all possibilities ... Whirlpool Dishwashers

Ok, after a year, I've figured out the problem. I changed a bunch of parts, but never until now figured out that what it is doing is, water is running out the hole behind the door, where the overflow dripguard sits, if the front three panels are on. when those panels are on, water, just before position 6, pours down that plastic dripguard piece, into the big tray. eventually the tray overflows. when you take off the panels, then water just pours onto the floor. if you open the DW, the basin is t


It could be as simple as the float switch inside the wash tub. Usually they are located just inside the bottom front edge of the dishwasher. Some of these are loose and others are enclosed inside another cover. \015\012\015\012You may hav ... Asko Dishwashers

Dishlex Global 300 Fills and then stops. faint electrical smell after a while . Checked heating element that I replaced 8 months ago, seems OK. It has 29X? ohms resistance and looks OK. (I am not sure of the reading on my meter but the element is not fused.) Pumps water in and out OK No blockage in pump or filters Water level looks to be low on filling, only part covers the heating element. I tried instruction book on changing water level using the "Eco" button no response as indicated in


You need to open the front cover and check the wiring for any burnt wire,this happen sometimes,if that does not solve then it't either pcb or electric motor causing this smell.You would be better off with a new one then. ... Dishwashers

Top arm is not getting enough water to rotate. The bottom arm is working good. Could this be caused by hard water deposits in the tube leading up to the top water funnel?


Yes it could but more likely the jets in the upper arm are clogged ... also often on older machines the pump wears to the point of not providing enough force for both arms .. even more likely there is usually a plastic screen surrounding the pump in ... Dishwashers

Kitchen Aid model KUDS01FLSS3, water gets pumped into bottom of dishwasher but when the cycle needs to change to shoot the water over the dishes nothing happens. When the cancel button is pushed all the water will drain.I have cleaned out the bottom drain compartment that was jammed with calcium build up and guck. Would this be a pump /motor problem or electrical circuit board problem?


... KitchenAid Dishwashers

KitchenAid KUDP01DLBS2 dishwasher. Runs for a very long time on any cycle; time does not seem to advance. (takes 2.5 hours or more for normal cycle. "sensing soak", "water heating" lights on for a long time, even though it appears that water is not being heated. Checked incoming water temp, is hot. Did not do this when new, something has changed. Typical cycle was 1 hr 10 min. before.


Sounds like the heater inside the dishwasher is not working. The machine is trying to get the water up to a preset temperature, probably in the neighborhood of 140 degrees. That is one of the things that it is sensing.After the machine fi ... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1009 seconds