Having problems with your Fagor LFA-019 SS Stainless Steel Dishwasher ?

The display reads f08

\015 The mechine attempts to run a program only to stop a few seconds later it will then display f08 .Have tried emptying the drain filter but to no avail.\015

Answers :

Repair Help & Product Troubleshooting for Fagor LFA-019 SS Stainless Steel Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Fault PP It pumps and pumps with a gradual flow of incoming water but doesn't get anywhere. The top display reads 188 with salt and the other warning light on (sorry, I only know the danish word - afspaendingsmiddel), the front display reads iPP (the i is raised).


A leak which has activated the flood safety in the base, you can check this by pulling the machine onto a towel and tipping the whole unit forward ie raise the back of the machine off the floor so it is pivoted on the front feet at approx 45 ... Bosch Dishwashers

My Hotpoint aquarius FDW75 dishwasher will not fill with water and when turned on the display reads H2O and then displays the code AO6


... Dishwashers

Display reading 188min with snowflake symbol on display on top of door


... Siemens 24 in. SE25A266 ExtraKlasse Free-standing Dishwasher

I have a Thermador dishwasher # dwhd650gfp with displayed error code 2, I verified oily residue on dishes and caked up grease on sump trap filter. This unit is 14 months old. I first reckognized that the dishes were not drying completely after cycle, then noticed the cold grease accumulation in drain area, then saw "E02" displayed on message board. I have read through some blogs that this issue could be a defective heater assembly, shorted or open circuit at the connection at the control pan


Hello,Welcome to FixYa. \015\012\015\012You would've been correct in your suspicion , of Bosch built dishwashers prior to this more recent revisions ... Dishwashers

Suddenly, an error message appeared on the display of my Frigidaire gallery series dishwasher, model number GLD3450RDS0. On advice from Electrolux customer service, we cut off the power supply for one minute. When we turned the power back on, the display read PF (for power failure), but then it went completely black. Any advice?


... Frigidaire Dishwashers

I have a Bosch SHU43C05UC diswasher. Last night, I put it on before going to bed as usual. I was awakened a couple of hours later to a loud grinding sound (like a pump being run dry), and found the noise coming from the dishwasher. The display read "0" time remaining, so I opened the door and the dishes seemed clean, so I left it shut off. Tonight I have been trying to troubleshoot the problem. The dishwasher will turn on, but it will not seem to fill with water. I have verified that the


Ok well before you can do anything you must obtain a service manual, link below.\015\012\015\012http://allrepairmanuals.com/bosch ... Dishwashers

Display reads f2 - Asko 1385 Dishwasher


Hello,Welcome to FixYa.Based on your description It is likely nothing very serious.The "F2" with Asko dishwash ... Asko 1385 Dishwasher

I have a Bosch (SHU5302UC/U12). The washer often takes 2 or more hours to run. Sometimes it gets stuck for a long time part way through (e.g. just sits at "43"). Other times, it gets stuck at 1 and won't stop on its own. The latest thing is 2 dots have appeared on the display that I've never seen before. For example, instead of "43", it reads "4.3." Eventually it gets to "C.L." but does not stop running. Also, its been making very strange noises during part of the wash cycle.


... Bosch 24 in. SHU43 Built-in Dishwasher

I have a Kitchenaid dishwasher #KUDK01LBS6.The unit will not run. The ''Clean Light'' indicator on the display panel blinks off and on. I have read that a ''Fault Code'' is needed to solve this problem, can you provide me with one? Thanks! e-mail [email protected]


... KitchenAid Dishwashers

My asko dishwasher(1504) keeps running sometimes, The time will run down to 1 min on the disply and stay there and run on and on until I turn it off. Prior to this another problem occured, when the washer does shut off on it's own, the display will read F1(Falt in the heater), I am wondering if one problem has to do with another. The heater problem I can deal with but not the continueous running.


F1 doesn't mean that it's always the heating element itself, often it \015\012can be the control board relay that has shorted and isn't sending power \015\012to the element. If the element is the faulty part, you'd be looking at \015\012about $250 f ... Dishwashers

Kenmore dishwasher model 1681590 reading E2 on display Help No owners manual and it just quit


... Kenmore 24 in. 17482 / 17484 / 17489 Built-in Dishwasher

My Bosch dishwasher is making a loud noise and the displays is reading 2H?


... Bosch SHU5315UC Dishwasher

Maytag dishwasher mdb7601aww program not working right. Lights on display not lighting. Push button and it reads 2 hour delay. Cannot get it to run without delay. Thanks, Bill


... Maytag Dishwashers

My Frigidaire dishwasher keeps showing the Er uo codo on the display. It used to would finish a load even though it would stop for a while when the error message came up, but now it will not run at all when the error message comes up. I read on this site that the Er uo has to do with the vent. I pulled the dishwasher out and removed the vent. I turned the dishwasher on and the vent opened and closed about three times when the cycle started, then it stopped and the error message came up. Is


Hi. This code is in reference to the vent assembly. This may also be a control fault, as well. To isolate the culprit, you will need to make sure that the vent assembly is not blocked. If it is blocked, it must be replaced. Restricted air flow will c ... Dishwashers

Mine is an LD2131SH ,as soon as i switch it on there is a ringing sound come and the display (next to the delay start button) is showing numbers upside-down ,cannot read at all ,suggesting an error somewhere.Grateful if you helped


Hi\015\012\015\012The ringing sound states that the control itself has gone bad and to resolve the issue should be replaced. Hope you understand, from what all you are saying it indicates an issue with the control. Please let me know if you nee ... LG 24 in. LDS 5811 Built-in Dishwasher

I need a new front panel and door seal for a customers dishwasher. It is a fisher and paykel Nautilas The opperating instructions say it is a model 920 . I can not read the model No from inside door as it has been cleaned off the sticker. The panel is black and has the led display on the right hand side


Check out www.applianceart.com ... GE 25 in. Nautilus GSC3400J Free-standing Dishwasher

My sink got clogged and now my bosch dishwasher SHU43C05UC wont fill with water. I read on line that it most likely is the float is stuck and to access the front kickplate needs to be removed. Is there a diagnostic test that I can do that will display on the LED to make sure that this is the problem. How involved is it to unstick the float. Can it be done without moving the dishwasher and just working from the kickplate area?


It is most likely that you need to do the following\015\012\015\012Larger remnants of food that have not been trapped by the filters and have been left in the water can cause a blockage in the pump. The water is no longer pumped out of th ... Bosch 24 in. SHU66C02 / SHU66C06 Built-in Dishwasher

He machine lets in limited water and then does nothing as the E1 error reading appears on the display.


Need model to help you as there are many machine and many differant codes ... LG 24 in. LDS 5811ST Stainless Steel Built-in Dishwasher

Hi! We just installed our LG LDF8812WW built in dishwasher. We ran our first cycle and after the wash cycle the dishwasher displayed error code OE. I read that it meant there is a problem with the drainage, and to check the hose if it is kinked. Well, the hose is not kinked and we have no idea why it would have a problem with the draining. We have the hose set up per the installation instructions. How can we check to for something clogged? Any suggestions?


I actually own an LG LDF8812 myself, except mine is stainless steel, not white. So be it. :-)\015\012\015\012Anyway, it sounds like you have just unboxed the unit and it is brand new, not just new to you. I am also ... LG LDF8812 Stainless Steel Built-in Dishwasher

Have Hobart CL-44E dishwasher that won't stop the 'fill' cycle. Both upper and lower float/probe sensors test as operating, Solonoid valves both functional; Display reads 'tank filling', and will not go into 'wash' cycle...what to do??


... Hobart Dishwashers

Display reading f40 - Miele 24 in. G2180Vi Built-in Dishwasher


... Miele 24 in. G2180Vi Built-in Dishwasher

We have a Turbo air dishwasher that is stopping half way through its cycle. the display reads E5. what does that mean and what should I do?


... Dishwashers

Temperature display on the booster led periodically reads the temperature as zero, even though the water temp is at 180. I visually checked the circuit board and it looks ok. Thermistor or board or both bad?


... Hobart AM14C-155 Dishwasher

My dishwasher read FL on the display, it is a kenmore solid state


... Kenmore Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0236 seconds