Having problems with your Fisher and Paykel 23 in. DD-603 Built-in Dishwasher ?

My Fisher & Paykel DD 603 has the fault code

\015 My Fisher & Paykel DD 603 has the fault code F1. I have turned the water and power off and cleaned all the filters impella and put it back together but it still keeps beeping and flashing F1. I think it needs to be reset, how do I do this\015

Answers :

Check at bottom housing both top and bottom drawers for leaks.
\015\012Pull the tube out, on the left side below the tub you can access to touch the bottom housing. Dry it out with a tower. Un plug the power cord at least 24 hor so the flood sensor can be dried out before pluggin it back.
\015\012However, if you don't fix this leak, the sam F1 problem will happen again.
\015\012There is not much clogging up in filter. If you expect something clogged up, you have to take the spraying arm off then take out the bottom stainless steel with a lot of holes out to see the impeller clean or not. Good luck.
Repair Help & Product Troubleshooting for Fisher and Paykel 23 in. DD-603 Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Fisher & paykel dishdrawer ds605 f7 fault code. Lid failure. This is the second code (after F9- power controller fault).The lid of the dishdrawer will not raise and release the drawer. The lid is stuck in the down position. Assuming this is a power/electronic controller fault. Part numbers would be good.


You can force open the drawer without causing any damage. The actuators on each side will let you do that. But you push it back in unless you manually move the actuators for which you will have to take the drawer out of its housing.\015\012 ... Fisher and Paykel DS605ZW Dishwasher

FISHER PAYKEL DISH DRAWER U3 FAULT CODE - Fisher and Paykel 24 in. DD-602 Built-in Dishwasher


LP is a setting for Low pressure. To reset your pressure to HP, hold the Programme and Eco touch switches simultaneously for 5 seconds. Once the setup mode is entered a beep is emitted andthe LCD is red with ‘HP’ or 'LP' displayed. ... Fisher and Paykel 24 in. DD-602 Built-in Dishwasher

Fisher and paykel e8 fault code - Fisher and Paykel Dishwashers


... Fisher and Paykel Dishwashers

Fisher and paykel diswasher f1 fault code - Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher


F1 fault code means the flood switch is activated. There is moisture at th e base of your dishwasher.\015\012 ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

My Fisher & Paykel DD 603 has the fault code


Check at bottom housing both top and bottom drawers for leaks. \015\012Pull the tube out, on the left side below the tub you can access to touch the bottom housing. Dry it out with a tower. Un plug the power cord at least 24 hor so the flood ... Fisher and Paykel 23 in. DD-603 Built-in Dishwasher

Fisher and Paykel Dishdrawer-DS605SS F4 fault code


No temperature increase ... Fisher and Paykel DishDrawer DS605FDSM Stainless Steel 23 in Builtin Dishwasher

FIX F1 FAULT CODE ON FISHER PAYKEL DISHWASHER MODEL DD603


... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

Beeping fault code Fisher and Paykel DS603


Stop the unit and check to see if it's heating when it's beeping at you. eg is it warm water inside at the time? if not you may have a faulty element. ... Fisher and Paykel 24 in. DS-603 Built-in Dishwasher

Fisher& paykel F1 Fault code


F1 means u have a leak on the machine somewhere. they leak from , lid, drain hose , lid activatiors, the leak has flood sensor to come on. to stop the F1 code u have to repair leak. please reply 4 more help. ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

Help with and f4 fault code on a fisher and paykel disher


Without the model number I have to guess.\015\012Fault code 'f4' means "faulty temperature sensor or element".\015\012\015\012Here is a link to User manuals:\015\012\015\012 ... Fisher Dishwashers

Fault code f1 - Fisher and Paykel 24 in. DD603H W Built-in Dishwasher


This could mean a lot of things depending on what the last state of the dishwasher is. For a double dishdrawer unit it could mean the power to the top unit has blown. But more commonly there is a water leak causing the flood switch at the base of the ... Fisher and Paykel 24 in. DD603H W Built-in Dishwasher

Fisher paykel dd603. Fault code appeared bL, now playing Star spangled Banner Tried turning it on/off with no joy. Any suggestions?


... Fisher and Paykel 24 in. DD-602 Built-in Dishwasher

Fault code f04 - Fisher and Paykel Dishwashers


... Fisher and Paykel Dishwashers

What is fault code f2 on fisher & paykel dishwasher


Rotor is not moving. Remove the spray arm, filters and the rotor, check for debris. Rotor impeller should turn if you try to turn it manually. If it does not - replace the rotor. Here is your part: ... Dishwashers

Fisher-Paykel DD603 DishDrawer shows F1 fault code. The Flood Switch has been activated. I need instructions on how to re-set the flood switch. I have two drawers that are possitioned one above the other and the are both giving the error of the activated flood switch. Any advice or instruction is greatly appreciated.


Fisher-Paykel DD603 DishDrawer shows F1 fault code. The Flood Switch has been activated. I need instructions on how to re-set the flood switch. I have two drawers that are possitioned one above the other and the are both giving the error of the activ ... Dishwashers

F2 Code Hey, I have a single drawer built in Fisher & Paykel dish drawer and today I pulled the spray arm, filter and large metal screen out to clean them as we have been starting to get a bit of stuff left behind after washing lately. That was all good After putting it all back in though I went to use the dishwasher and it stopped and came up with an F2 fault, I thought I may not have put the bits back in properly so pulled them out again and noticed that on the rotor that connects the motor to


Fault F2 means the rotor is not rotating. If you say some of the vanes have broken off, they could have been jamming it. This should spin freely with minimal force when installed correctly. If you removed the rotor itself, you do ned to take care whe ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

Fisher & Paykel DD603 model Upper Dishdrawer has F3 fault code. cycke starts, then stops within minutes. Water in tub after stopping is not hot. Temp sensor bad? Could you please send pdf of servie manula for dd603 please? Thanks [email protected]


F3 means your dishwasher water is too hot. Go to the link below and it will show you how to determine what is causing the error. ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

F&p dishdrawer fault code u3 - Fisher and Paykel 24 in. DD-602 Built-in Dishwasher


Http://www.fixya.com/support/t777079-model_601v2_dishdraw_showing_u3 ... Fisher and Paykel 24 in. DD-602 Built-in Dishwasher

Fisher& Paykel Double dish drawer dd603 fault code f1, what do we do?! Where is the flood switch?


See also http://www.fixya.com/support/t346941-f1_error_1_draw_dishwasher ... Fisher and Paykel 24 in. DD603H W Built-in Dishwasher

My Fisher Paykel dishwasher is model #DD6051. After about 1 1/2 years, the top drawer is not filling with water. The fault code looks to be U1. The bottom drawer fills and runs fine. Would you have any idea what the issue might be? Thank you very much.


Hi,Unplug the Washer for Few Minutes, say 30 minutes and then Turn it ON. If the problem Persists, then read :-U1 Heavy and Rinse LEDMachine has failed to prime with water within approx. 3 minutesReason ... Fisher and Paykel Dishwashers

F1 fault code flashing - Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher


Inlet hose to inlet valve connection looseInlet valve body leakDamage to the fill or drain hosesHeater plate damage (chipped enamel)Seals/O Rings (pinched, contaminated or poor join)Dispenser (seal, diverter valve or wel ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

Fault Code E4 - Fisher and Paykel Dishwashers


... Fisher and Paykel Dishwashers

The F4 fault code on my Fisher and Paykel Dishdrawer Model DD603 dishwwasher indicates that the "temperature sensor is faulty. Question: where is it located on the machine and how do I replace it?


The temperature sensor is located on the heater plate(looks like a blob of solder with a thin line leading to a blob of solder,The solder acts as a fuse when it "blows"you have to replace the heater plate.The heater plate is located in each draw (ge ... Dishwashers

I have a Fisher and Paykel DD24D Dishwasher just installed and the fault code U keeps coming on, which says no water, I checked the water supply, it is try on, so now I'm at a lost.....thanks


If the unit is new do not try fix it or have it fixed, or even look into it, call the dealer or take it back to him as you will invalidate your warranty if you do anything to the unit, and that is not worth it. Let the dealer worry about it. ... Fisher and Paykel DD24D Dishwasher

Hello, We have a Fisher Paykel DD603 dishwasher. I have spent $400 on parts and service call and still have same problem: U1 fault code. I have changed water inlet valve and electronic controller. I'm exasperated. Anyone with suggestions ? Jeff G.


... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0615 seconds