Having problems with your Fisher and Paykel 23 in. DD-603 Built-in Dishwasher ?

On 2 door dishwasher model DD603 bottom draw is very hard to slide out or in. Can i remove draw to inspect and oil draw runners?


Answers :

Hi- Most likely the lid is stuck in the down, or partially down position. This is usually caused by the lid actuators (motors) not returning the lid to its full up position and therefore the drawer top is dragging on the lid gasket. Replacing the lid actuators should resolve the problem. You'll need a F/P tech to change those for you. Hope this helps.
Repair Help & Product Troubleshooting for Fisher and Paykel 23 in. DD-603 Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

On 2 door dishwasher model DD603 bottom draw is very hard to slide out or in. Can i remove draw to inspect and oil draw runners?


Hi- Most likely the lid is stuck in the down, or partially down position. This is usually caused by the lid actuators (motors) not returning the lid to its full up position and therefore the drawer top is dragging on the lid gasket. Replacing the l ... Fisher and Paykel 23 in. DD-603 Built-in Dishwasher

Dishwasher (Model # SHU6806UC), unit is about 8 years old, very light use, less than once a month, and no previous problems. Turned on unit and after about 10 minutes, I found water on floor coming from dishwasher. Turned unit off and turned off water shut-off valve. Removed dishwasher from cabinet. Found mice had chewed a hole in water discharge hose under unit, inspected all hoses, and found another hole chewed in the 13" flex hose in the front of the unit. Also found the float chewed to alm


Hi,\015\012 Check the valve is open where the supply gets its water from the sink supply.There is a garden hose type swivel adapter after the valve, Close the valve tightly and then unscrew that hose coupling and see if the hose is full of w ... Bosch 24 in. SHU6802UC / SHU6806UC Built-in Dishwasher

My dishwasher is a Smeg model STA 6143, and the door won't close. It seems fine until the last few centimeters, then it jams and won't close easily. If you press hard, it'll shut but not latch. Nothing appears to be stuck anywhere. We've tried jiggling the door but it seems somehow to be misaligned, although there's no reason why it should all of a sudden appear to be so. The electronics work fine, the racks fit fine (we also removed them, and the door still won't close), and nothing appear


... Dishwashers

Need to replace the latch assembly on Maytag dishwasher model # MDB5600AWW. How do I gain access to the area where I need to replace the part? I removed the 5 screws at the top, but can't seem to get the upper front panel off. I'm afraid of pulling on it to hard.


Remove all the screws on the inner door panel and lift it up it will be easyer ... Dishwashers

I have a kenmore dishwasher, model 587-1625. Noticing that are dishes didn't seem to be getting very clean. I removed the drain screen and cleaned, noticing a lot of hard water deposit. yet, it still drain. Now after cleaning it doesn't drain now what?


Check for a plugged air gap (on top of the sink) ... Kenmore Dishwashers

LG model LDS5811WW/02 has never cleaned the dishes since first installation. Put clean dishes in and they will come out dirty too! Have tried all dishwasher soap types and brands and drying agents. Always scrape and rinse dishes prior to loading. Dishes loaded various ways but problem remains. Repairman says unit is working fine. Also never dries dishes completely. Often leaves soap dispenser completely or partially filled. We are on a farm and have hard water but we have a softener/iron remover


If the soap/detergent isn't completely rinsing out of dispenser, it sounds like water isn't directed the top spray-arm. possible a defective vario motor; as it directs water to the water channel that supplies water to the middle and upper spray arms. ... LG LDF8812 Stainless Steel Built-in Dishwasher

I have a Fisher and Paykel dishdrawer model ds603. Not sure eactly what happened but my son says that the cycle stopped last evening (and only tells me this morning!). Dishes though appeared to be clean and there was a small amount of water at the bottom. I tried opeing the washer and it was hard to open as though the drawer was stuck on something. I removed the drawer and checked the rollers and they are fine. I realised then that the drawer is getting stuck on the inside lid that provides the


The best thing to do is to remove the rack,drawer completly,and close it up,see if it will come on,and run all threw the cycle.If it does,then put the rack,drawer on the track.The rollers could be,well,not snapped all the way on.It will be in that ar ... Fisher Dishwashers

I pull the Ripcord and doen not start. The ripcord feels very hard when pulling. When I remove the chamber and inspect the cord mechanism, it seems to be working fine. thanks for the Solution


... Honda Pressure Washer PSI 3000

MY GE WATER SOFTENER QUIT WORKING PROPERLY AFTER 6 MONTHS ,I HAVE HAD SERVICE CALLS AT $150 EACH TO NO AVAIL IT DRAWS SALT BRINE MY WATER HARDNESS IS 17 I HAVE SOFTENER SET TO 22 .I HAVE PRE WATER FILTERS HAVE TRIED DIFFERENT SALTS ALL TO NO AVAIL, NEITHER GE OR HOME DEPOT WANT TO HELP AS NOW I AM OUT OF WARRANTY I HAVE BEEN ILL AND IN THE HOSPITAL (CANCER) THAT'S WHY I HAVE GONE OUT OF THE WARRANTY TIME MODEL GXSF30H PURCHASED 19/02/10


As you have purchased GE water softener and stop working after 6 months,then you need to check it from an expert technician and if he is able to solve this issue,then it good and well, but if this takes more money to repair and not under warranty the ... GE 30000 Grain Water Softener GXSF30H

Door latch I have this model and the door latch is not working....have hard time opening it now. How do you remove the tope part of the door that contains that latch so I can put in back in place????


The latch is fairly simple to replace. There are several screws around the inside of the door that hold the inside panel in place. You then will be able to slide the panel out of the way (it is attached by wires).You will then be able to ... Maytag 24 in. MDB6600A Jetclean II Built-in Dishwasher

GE Dishwasher model PDW8200J03BB stopped draining. Removed the drain pump, checked with Voltmeter and there is resistance on ohms X10 of about 3. The flap is in place so water isn't shooting back into the sump inlet. Replaced the sump inlet about 6 months ago because it was deteriorated due to hard water. Pump worked fine after that. Checked drain hoses and air gap. Was able to blow water through. Pump only trickles water out at air gap. Does the pump need replaced?


Clear the line from the air gap to the drain,, if the rest is clear the only thing it can be is the propellers on the pump, i which case you will need to change the pump ... GE 25 in. Profile PDW8200J Built-in Dishwasher

Honda 11 hp, model GX340, Cat pump model 5DX40GL; Low on hydrolic oil need to know what type of hydrolic oil to use.


... Honda Pressure Washer PSI 3000

Cannot figure out how to remove the oil plug to drain the oil. Label points to a spot that looks like it might be a plug, but can't figure out how to remove it. It is a 2500 psi Mdl VR2500 Briggs & Stratton engine Honda Power Washer. Ken from NH


Should take a 3/8" socket extention ... Pressure Washers

GE gsd2350r00cs fine filter removal. Once the spray arm is removed how do I remove the fine filter? does it pop out of the back? Don't wat to break it if I pull too hard and it's not supposed


... GE Dishwashers

Dishes all cloudy and spotty. Maytag Intellisense plus 1996 dishwasher. I have real hard water that leave white calcium build up. I can remove and clean all of the lower spray arms and filter. How do I remove top spray arm to remand remove deposits? The motor sounds good, hot water, fill ok. On the inside top of center of arm where it meets the center input connection there is gunk to remove. How do I get to it? remove arm? thanks


The problem is hard water. Go to www.dishwasherfilter.com. They have a new product out that solves this problem once and for all. It filters the water entering your d ... Danby 22 in. DDW399 Free-standing Dishwasher

Hi, I have a Dishlex dishwasher. It's an electronic model, from about 92 I think. The model I thought was B8557WW. It is very hard to see the model number because it's almost washed away. Is the model number maybe located anywhere else on the machine? Could there be a manual or circuit diagram hidden somewhere on (in) the machine? The fault is that it wont start. It reacts to some of the front buttons, and beeps, but not all, and not the start button. Before it stopped working completely, some o


... Dishwashers

The slide on the upper basket keeps falling out. It's been fixed twice but doesn't hold. The second repair man who put the slide back in the rollers said he couldn't see anything wrong with it, but it still didn't hold, so he called your tech dept. who said they had roller and slide kits at a total cost of $66 for this model. The slide kit had a new part number but the tech department didn't tell the repair man why they'd changed the part. The roller kit was one for dishwashers the sides o


One option is installing stainless steel washers on the rack supports that screw into the side of the tub. The rack falls down because there is too much "slop" with the rack...a couple small washers to space them tighter normally does the trick. ... Frigidaire 24 in. PLD2850 Built-in Dishwasher

I have a sears pressure washer, model 580752300. The pump on the underside vibrated lose and broke a couple screws. It came off and the oil drained out. I replaced the screws and it's ready to go except I can't find out how much replacement oil to put back in. Sears has larger containers but won't tell you how much oil to put in. However, there's a pricey pre-measured container they want to make you buy. Anybody know how much oil goes in that pump?


... FAIP Non Marking Pressure Washer Hose 4000 Psi, 50ft. Length

What of oil is used in pump of a simpson power washer model msv 3100 ,not the engine oil. the pump oil ,it's life time oil


... Pressure Washers

On a GE Dishwasher Model GSD5200G00BB what is the procedure to remove the lower spray arm? I need to remove it so I can remove the screen covering the entire bottom of the dishwasher. There is a tremendous amout of mineral build-up in the dishwasher (under the referenced screen) that I want to remove.


... GE Dishwashers

JENN-AIR Model number JD3B10AWX. Bottom of dishwasher is dirty, I want to clean it. I have removed six screws holding plate down, but cannot find any way to remove spinning blade. I think there's a filter underneath that I can clean or replace. Questions: 1. How to remove spinning blade? 2. Am I going about this correctly. Thank you


We have been having issues with our model where there is dirty sand deposited inside of glasses and dishes.You need a torque wrench for a triple square torque screw ... Jenn-Air Dishwashers

I have a KitchenAid Sculptura dishwasher and it have been leaving food particles on the dishes. I started to take it apart, removing the bottom spray arm. I can see a lot of old food underneath. I'm having a hard time removing the next piece. There is a 1" rubber nut with a screw in the middle. Is this the next step for removal?


Hi\015\012\015\012Thanks for using FixYa. Please post back with the model no of your Kitchen Aid Sculptura Dishwasher so that I can further assist you.\015\012\015\012\015\012Thanks\015\012Ryle ... Dishwashers

Model probably 039-119 or WKZ solo model or GV630 S/U no official model plate. about 8 years old. bought with a service top. we want to remove the service top.


Hi noel,the part and how to remove the part you are targeting is shown on the link below as with other Bosch dishwashers.http://www.repairclinic.com/Dishwasher-Repair-Helphttp://www.devicemanuals.com/guide/Dishwash ... Bosch Dishwashers

I am trying to replace the GUIDE RAIL BRACKET ASM on my GE dishwasher (model no. GSM1800JWW). How do I either: (a) remove the old brackets, and then install the new ones; or (b) remove the rollers from my new brackets, so that I could slip these rollers onto the old brackets still in the dishwasher, saving the trouble of removing the old brackets in the first place? Either solution would be acceptable, but right now I can't figure out how to do either one without breaking something. Thank you v


Be ready for both . because if they break you can still replace it. but (a) is to me the better choice. let me know how you made out and send me a 4 thumbs post if it works out ... Dishwashers

I have a MODEL 577-0 kudk01ILb55 KITCHENAIDE dishwasher. I am trying to remove the inner pplastic bar that goes vertically through the system from top top bottomj so that I can clean out the filter. But I do not see how to remove that bar. I have looked online for a repair manual of some type but have been unsuccessful. Can someone tell me how to remkove the bar so I can get to the filter on the bottom? I have already removed the star shaped rinse sprayer.


... KitchenAid 24 in. KUDS01FLBL Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0772 seconds