Having problems with your Fisher and Paykel 23 in. DD-603 Built-in Dishwasher ?

Can't stop both dishwashers. Both are running and showing wrench on display


Answers :

Through the ******* thing in the garbage
Repair Help & Product Troubleshooting for Fisher and Paykel 23 in. DD-603 Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Can't stop both dishwashers. Both are running and showing wrench on display


Through the ******* thing in the garbage ... Fisher and Paykel 23 in. DD-603 Built-in Dishwasher

My Frigidaire dishwasher keeps showing the Er uo codo on the display. It used to would finish a load even though it would stop for a while when the error message came up, but now it will not run at all when the error message comes up. I read on this site that the Er uo has to do with the vent. I pulled the dishwasher out and removed the vent. I turned the dishwasher on and the vent opened and closed about three times when the cycle started, then it stopped and the error message came up. Is


Hi. This code is in reference to the vent assembly. This may also be a control fault, as well. To isolate the culprit, you will need to make sure that the vent assembly is not blocked. If it is blocked, it must be replaced. Restricted air flow will c ... Dishwashers

Gaggenau GM915-710 When I turn on the dishwasher, the display says 13 and the washer runs. But it run until the displays shows 1 and it is stuck there. I hear the machine going but it never stops.


... Gaggenau GI936-760 Dishwasher

Just had new Frigidaire dishwasher installed. When cycle is started, display shows 99. Unit will fill with water, run cycle for about five minutes, stop and empty water then display a flashing PF. Can not seem to find a list of codes for this.


Pf is means power failure. ... Frigidaire 24 in. PLD3465REC Stainless Steel Built-in Dishwasher

My dishwasher has stopped mid cycle showing 1 minute left , when stopped and started again it now shows 28 minutes contantly, plus it continues to run (ie pump running) after the door is open. Any ideas ? many thanks Doug


Hey dcp667\015\012\015\012Dishwashers are incredibly durable machines. They can take years of daily use and in many cases, it's only a change in decor that brings about a replacement. Of course that doesn't mean things never go wrong with ... Dishwashers

I have a Bosch SHU9955US/14 (Integra) dishwasher. There is currently a 0 with and asterisk showing on the display and the unit will not run.


See this causes and fix it. God bless you\012 \012 \012 \012 \012 Thermal Fuse\012 \012 \012 \012 \012 \012 \012 \012 \012 ... Bosch Dishwashers

Dishwasher Dilema Hi, Can someone help me solve this problem. Last time I had a problem with my dishwashers I was pretty successful in solving it on this site. I was running a reg wash on the top drawer of my Fisher&Paykel when I suddendly had to stop it in the middle of a wash to add more dishes (something I do all the time) suddenly both screens started beeping with an F1 along with a wrench. It sounds like both motors top and bottom are running full blast. I tried shutting the power for a few


You need to remove the bottom drawer and dry out the water with towels and a hair dryer when this is done it should operate normally. most likely when you pulled out the drawer the water sloshed back and out of the drawer making the dishdrawer think ... Fisher and Paykel 24 in. DD603H W Built-in Dishwasher

Bosch SHU43 My Bosch SHU43C dishwasher stopped washing, turns out the impella came free from the motor, I repairded impella and put it back together and now the dishwasher washes great however now it is stuck in a wash rinse drain cycle. Display counts down but the unit never stops running when it reaches 0. Also, the water level is higher than normal and I there is a kind of thumping sound repeatedly every 15 seconds " use to make that sound only once at the start of a cycle before the impella


Sounds like the control module is out -- cost about $100 (I am on my third). I got a "lifetime" warranty when buying my second one. If you are handy, you can replace it yourself. You can call Bosch to confirm this (I did). It mounts inside the door. ... Bosch 24 in. SHU53 Built-in Dishwasher

Smeg dishwasher model DI 612 C type 12053 good morning After selecting a program and shutting the door the drain pump starts and runs for 2 seconds then stops. The machine makes a bleep noise then the drain pump starts again running for 2 seconds then stops again and the cutting in and out process continues and the machine never reaches its selcted cycle. No alarm lights are displayed. I have filled the machine with water so that the filter is submerged and the level is


... Smeg Dishwashers

Hi There, I have a F&P 918td dishwasher which has stopped working. Whenever I press any of the buttons I get 5 very quick beeps and then nothing - no error message, nothing the display is blank. If I turn it off at the wall and then back on again the display briefly shows two characters that do not show up in the manual as valid errors. Any ideas anyone?


Sounds like a fried board. ... Dishwashers

Hi , i have westinghouse dishwasher model SB915SJ. when i put it to wash on eco normal, it stops a after about 20 minutes and i have to press the program button to start it working again. it's currently running now but it stops about every 4 minutes and the numebr 20 appears in the display screen. if i push the program button it will rung for another 4 minutes then stop, start beeping and the number 20 appears. how can i fix this?


Www.westinghouse.co.nz/...westinghouse/.../NZ_WH_Dishwashers_May06.pdf \015\012\015\012\015\012\015\012Above is your user manual, and below is your service and repair manual.\015\012 ... Westinghouse Dishwashers

Euro dishwasher model ED12GWA run for 101 minutes then stops & shows error code E1


... Dishwashers

ASKO dishwasher my dishwasher came on spontaneously and keeps running first (drain, I believe) cycle. It stops when I unplug it (of course- no power) but sturts immediately when I plug it back. Error message is displayed


F2 fault water in the base remove dishwasher from under the bench and tip back water will run out,then it will restart.remove rear lower panel and run the dishwasher you may find a leak,also check that the inlet valve is shutting off and not filling ... Asko D1776 Stainless Steel Built-in Dishwasher

Kitchen Aid Superba Selectra 21 Mod.: KUDS21SS1 MS S/N: FE 84757436 After whole house power outage, dishwasher began constant high pitch beep or whine. Machine controls unresponsive; display shows F. Cycling power has no effect {except noise stops and display goes off when powered down - of course). Any troubleshooting and parts availability advice would be greatly appreciated!


... KitchenAid Dishwashers

Hi! My Bosch dishwasher (SHE46C02UC/22) will not shut off. The display says "1" - like there is 1 minute left, but it will not stop. Yesterday morning I started the dishwasher at 7:30am and at 11:30am I realized that it was still running. I opened it and it still had soapy water on the dishes and had not cleaned the dishes well. Any ideas?


... Dishwashers

OE is displayed on my LD-1415M dishwasher. ive cleaned the filters, checked the hose and run cleaner through but the cycle just stops and OE is displayed again.


... LG Dishwashers

Dish washer will not run through cycles. No error appears on screen. Time display shows on led screen, however dishwasher will not run. How can I solve this problem?


Have u tried turning off the power to t and see if it reset and then trying it again ... Fisher and Paykel DD605SS Stainless Steel Dishwasher

Kenmore 15895 dishwasher, stopped running. There is an 18 in the display and after a day or so of sitting the pots and pans light comes on steady with 18 going out. The only reponse from the controls is that it sounds like it is doing something for a minute and stops.


Hi\015\012\015\012 \015\012\015\012Thanks for using FixYa. To resolve this you will have to reset the console. Do this\015\012by closing the door and press these buttons in sequence... ... Kenmore Dishwashers

Hi - my Viking dishwasher has developed a problem where the pump runs continuously, whether the power switch is ON or OFF. After the power is turned ON, the troubleshooting guide indicates that there is too much water in the dishwasher. (One of the pot symbols on the display flashes continuously to show this indication.) I am unable to switch between programs, e.g., from quick rinse to pots & pans. I cleaned all the filters to no avail. I had to secure the circuit breaker in order to turn t


If you open the kick plate, you'll see the pan below the motor and check for leaks. The leaks will trigger the sensor to pump water out. Once you dry out the pan, the pump motor will stop and you should be able to reset the program. ... Viking DFUD042 Built-in Dishwasher

No water When I start the dishwasher, the display shows 96 and starts to go down but there is never any water entering the machine and "HO" starts blinking. The dishwasher has been running fine up until today.


First swith the machine and the water supply off and then where the inlet hose is on the back of the machine remove the hose from the machine and look in the plastic part that the hose screws onto there should be a small sieve there this can be pulle ... Frigidaire 24 in. FDB1050RE Built-in Dishwasher

Program stops When the machine is switched on it runs for a minuite or so then stops and bleeps and shows blanks - - - - I switch it off and again re-start and it again repeats this as above the filters have been cleaned and the water was drained and again it persists, the machine is 3 yrs old. I tried a sequence described as switching the programm button in 4 quick times but this didnt work either. Is there any other way we can re-programe this dishwasher or is it that there is a fault where so


... Smeg 18 in. DWD409SS Built-in Dishwasher

My Bosch integrated dishwasher(model SGV56A03 GB/12) runs through the cycle but doesn't stop at the end of the cycle. It continues to heat water and it sounds like the motor is running even though the time indicator shows 0 minutes. I have to manually switch it off. Any ideas before I call out an engineer. I have checked all the filters etc included in the troubleshooter info anf there are no blockages.


... Bosch Dishwashers

My bosch dishwasher control panel displays 0H on the time delay. When I start it the OH go to 2H. It then starts running and does not stop. The cycle minutes don't display. It's model number SHU5302UC 14. I do not have a manual and cannot find one online. Thanks


Check to see if your unit has a recall on it because if it does you will get a free control module from bosch.\015\012your problem is the control module. thermador .com is the site to lookup. gaggenau,bosch,thermador they are the same ccompany. ... Bosch 24 in. SHU53 Built-in Dishwasher

GE Profile Dishwasher, GSD4920 won't stop running. Still spraying water. No lights on the display. Looks like it ran all day since I started it before work. I turned power off and back on, but it still starts running when I close the door. Water is in the bottom and looks pretty dirty. Any ideas? Thanks, Larry


... GE GSD3800G - Multiple Color Built-in Dishwasher

My dishwasher SL34A015UC / 29 does not complete it's cycle. The cycle will stop with 1 minute left in the rince cycle and continue to run for hours, showing just one minute left. The dishes are not geting clean and there is a unplesent odor inside. I can hear the water draining during the cycle. The drain line is clear and there is plenty of water in the dishwasher. Any thoughts?


... Siemens SL5A70UC 24 in. Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.2271 seconds