Having problems with your Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher ?

Fisher & Paykel DD603 model Upper Dishdrawer has F3 fault code. cycke starts, then stops within minutes. Water in tub after stopping is not hot. Temp sensor bad? Could you please send pdf of servie manula for dd603 please? Thanks [email protected]


Answers :

F3 means your dishwasher water is too hot. Go to the link below and it will show you how to determine what is causing the error.

http://www.appliancerepairlesson.com/category/dishwasher-common-issues-repair/

Good luck

http://www.appliancerepairlesson.com
Hi- sounds like the controller is not sensing the right temp or possibly the heater plate is bad. I'd get a Tech out to take a look. The controller is not cheap unfortunately. These units should not be taken apart unless you really know what your doing. I've had to repair a few that other untrained Techs have damaged... Good luck.
Repair Help & Product Troubleshooting for Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Fisher & Paykel DD603 model Upper Dishdrawer has F3 fault code. cycke starts, then stops within minutes. Water in tub after stopping is not hot. Temp sensor bad? Could you please send pdf of servie manula for dd603 please? Thanks [email protected]


F3 means your dishwasher water is too hot. Go to the link below and it will show you how to determine what is causing the error. ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

After starting wash cycle the rotary dial advances to what appears to be the second phase and stops at about 1 oclock position. I replaced the timer/switch, same problem. Could I have a water temp sensing problem due to a poorly adhered sensor? I thought this may be the issue as the sensor at the water feed near the soap dispenser was loose on inspection. Model Bosch SHU4002UC/U06 Under counter Dishwasher


Check the thermostat sensor. If the sensor is faulty the amchine will not detect that the right temperature is reached and the cycle will not advance.The thermostat will read low ohms (about 1K) using a multimeter at Rx1 at ro ... Dishwashers

My dishwasher stopped working when i pulled the code it came up with heater temp sensor ..the water is getting hot ..where do i find the part on the dishwasher


... Maytag MDB8859AWS Stainless Steel Dishwasher

I have a Whirlpool which just recently started leaking from the door occasionally and it is most unpredictable. It eventually stops, but before it does it will deposit about a pint of water. I have replaced the float and the float switch, thinking those were the cheapest parts and perhaps the switch was faulty and letting too much water in. That did not work. When this happens I checked the exhaust and hot steam is coming out. Could it be the water inlet valve? If the seal was bad I am ass


Hi\015\012\015\012The issue is with the water inlet valve that is bad and\015\012should be replaced. I believe everything else is working fine. Hope this\015\012helps...please post back for further assistance.\015\012\015\012Dani ... Dishwashers

The top drawer of my fisher paykel dishwasher stops during the cycle and shows an icon of a tap with a line threw it (assume that means no or low water pressure). the bottom works fine so I assume water pressure is not the issue; is there a sensor that could be bad? Also, I did switch the controllers between drawers (good instructions on the fisherpaykelparts.net website) but the problem stayed with the drawer, ruling out the controller.


Did it fill with water? could be 1 of your water valves is faulty, or the little filter for the inlet water is blocked. please reply 4 more help. i"m sure i can fix this problem for you. good luck. ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

LG dishwasher. Stopped working mid cycle. Model LD~1204W1. Able to turn on and off. Able to press all other settings so can change wash temp, half load, full load etc. but cannot start programme. When press start makes a double beeping sound and nothing happens. Help as live in hot country and water is going to smell bad pretty quick. Thank you.


... LG Dishwashers

Help please i have an Electrolux esl 6115 please could you explain where the temp sensing element is situated.


... Electrolux Dishwashers

Tank temp Our School Dist. has a Hobart dishwasher Model AM 15 T. After filling the unit it reaches a tank temp. of approx. 160 F, but when it is run through a couple cycles the temp. falls below 140 F, the min. wash temp is 150 F. The supply from the hot water tank is approx. 140 F. The rinse cycle reaches well above the 180 F min. Is there anyway to adjust the tank temp. on this model or could you suggest a solution to the problem. Thank-you John Fry


Check to see if your element is scaled up or your element may be damaged ... Hobart AM15T Dishwasher

Hi, my name is GAD. i work at a conference center. our model is quite an old version of the MH65-70 - maybe 1985? How do you adjust the water temp for both the rinse and wash cycles? the gage reads too hot. we have someone here who can service it, knows how to work the electrical, but does not know where to adjust the water temp. Is it a dial? a bolt adjustment? how do we lower the water temp sensor?


Hello Gad\015\012Send me the serial No. of your unit and let me see whether we are talking the same machine. \015\012The one I'm talking about have 3 thermostate with dial to adjust the temperature 1 for Hi temp safty no dial fixed tempe ... Moyer Diebel 28 in. MH65-70 Free-standing Dishwasher

I need to repalce the elctrical supply cord and water supply line to my Fisher & Paykel DD603 dishwasher, but I'm unsure as to how to remove the terminal box cover. Could you please help? Thanks.


THIS IS SIMALAR TO THE BOSCH UNIT, IF THERE IS NO BOTTOM COVER TO REMOVE YOU NEED TO TAKE THE SCREWS OUT OR THE TOP INSIDE THAT HOLD IT TO THE COUNTER TOP, PULL THE UNIT OUT SLOWLY, TURN OFF THE WATER SUPPLY SHOULD COME OFF THE HOT SIDE OF YOUR FEED ... Fisher and Paykel 23 in. DD-603 Built-in Dishwasher

HDW101SS does not heat water. Heater element mearures 28 Ohms. Temp Limiter is N.C. Temp controllers TS50 & TS60 not found. On economy wash timer moves as normal then stops when red heater light should come on. If the timer is assisted one click it will progress as normal but no hot water.


Hi.If the temp limiter shows no continuity, there will be no voltage reaching the element contacts. The high limit is connected in series with the heating element. If the hi limit is open the element will not get power. Any technician wil ... Haier HDP18PA Stainless Steel Free-Standing Dishwasher

Hi my teka dishwasher is causing me grief.The water starts but does not stop going all day on extreme hot temperature.I have stopped it as i opened the dishwasher and all the water remains in the bottom which is very dirty.Also it doesnt clean the dishes at all .So im so confused to what to do ..please help me thanks


Might help if you provide the model no. of your Teka dishwasher.\015\012\015\012also have you noticed any flashing lights or lights that come on when the wash is on. ... Dishwashers

Suddenly stopped functioning. The fridge light is on and if I turn the fridge freezer off and then on again, I can hear the motor start up. I'm guessing it could be the thermostat!. If you agree with the diagnosis, could you please let me know the part number and where to locate it in the appliance. Many Thanks Chris Paradise


Compressor failure.very expensive ... Hotpoint 24 in. FDW60 Free-standing Dishwasher

Hi Masters! My dishwasher was stopped during the program and the second LED ( from the four ) is flashing. Please send me the ARISTON LS 248 T dishwasher error code list if you could or please give advice for me. Many thanks,


... Dishwashers

Leaking This is a problem that I have when the dishwasher is in drying mode. I will find a 5X5 and sometimes smaller, size water spot under the dishwasher after the dishwasher has stopped. I was told it was the vent were the steam comes out and I had that replaced. It still leaks, then they told me to replace the rubber around the door, still leaks now they order a whole new plastic interior door. Please if you have any ideas what could be causing the problem, please let me know. Thank you


\015\012open the bottom panel 2-4 screw\015\012take a flashlight and turn the machine on\015\012see where it come from\015\012if you need take the unit out a bit f ... Jenn-Air JDB4000AWS Stainless Steel Dishwasher

I also have a dishwasher (AEG Favorit), and it does not heat the water anymore. It worked fine for last 3 years, and all sudden, it only washes dishes with cold water. Could you please help to solve this problem? The hot water line is fine and I do have the hot water to the sink next to the dishwasher. Thank you in advance for your help.


... AEG 23 in. Favorit 44070IW Built-in Dishwasher

I have a kenwood dishwasher kdw12sl3a. It shows fault E3. It states in the manual that this fault means longer heating time but not reaching required temp and its a malfunction of temp. sensor or heating element. Is there anything I could do to fix it or will it have to be sent back.


Aye have same problem!? how did ya get it fixed if ya did thanks ... Dishwashers

When I use my Karcher pressure washer it works perfectly until I release the trigger. Instead of remaining silent until I pull the trigger again the motor intermittently, at approx 2/3 second intervals, starts and stops. Could you please advise what is causing this to happen please.


What it is doing is keeping the pressure up in the hose. It is completely normal for it to do that. they all do it. Listen to others in use and it will do the same thing. Nothing to worry about. ... Karcher Pressure Washers

I have an older under the counter high temp dish washer not sure the model number but it has the three switches on the lower left, has both upper and lower wands and it is high temp. Not for sure but it seem like the homing cam switch is not working you can manually turn the came to get machine working but when it shuts off it wont restart when you close and latch the door could you please help!


The cam switch may be faulty and may be available for replacement.\015\012\015\012Hard to find replacement without model no. but for the current model it is available ... Moyer Diebel Dishwashers

My Hotpoint FDW20 dishwasher does not heat up and is washing cold. Could you, please, suggest a solution to the problem. Can you also forward me a circuit diagram for the machine along with a manual with the location of various sensors, switches and other electrical components and the wire colouring to these components. I am an electronics engineer by profession so if had a circuit diagram and a legend of the various sensors and switches along with their location on the machine it should be pos


Hi,Check your heating element.. \015\012A bad heating element causes many problems in dishwashers...Dishwasher Problems The Heating Element n ... Hotpoint Dishwashers

We have the Technika TDX6SS-2 and the heavy, fast and pre-rinse buttons are flashing and beeping - stops momentarily then commences again. There is no way to stop this. Could you please help with this problem? Thanks, Deirdre


... Dishwashers

Hobart dishwasher sitting at hot temp (174), constant steaming from unit, bottom rinse wand spinning & humming non stop? We reset prior to problem because it was not rising to temp (sitting at 106-112)


Bad thermostat or contactor ... Hobart 24 in. LXIH-3 Built-in Dishwasher

Continuous beeping and lock is intermittentyl showing on DD603, have tried turning off power, holding in lock button, turning off for 10 mins etc. CAnt stop it and driving us insane!! Can anyone hlpe us out please? Cheers, EFC_Blue


You need to Call the Fisher & Paykel customer service line and tell them that your Unit is Experience a Power Malfunction Usually its related to water leaking. ... Fisher and Paykel 24 in. DD603H W Built-in Dishwasher

We live in an apartment and our hot point dishwashers timing is all off and i thought if i could fix it myself, i'd love to do that instead of calling our manager, i will call him, but if its an easy fix i'd like to try it out.. it will just stop in mid cycle, and you have to manually more it a fraction of an inch to get it restarted, then at the end it doesnt fully drain, and the drying takes forever, so if i cant fix it, i'll ask for a new one..


It might need a new mechanical timer (sounds like the timer is sticking) installed and the parts will cost money... so you might want to go the route of the manager. The dial that you turn to set the dishwasher is part of the mechanical timer. Someti ... Dishwashers

Hi I have an older model Gaggenau Dishwasher (10-15 years) and during the wash cycle it seems that the water stops and the element heats up red hot? Any ideas on what could cause this problem? Thanks


... Gaggenau GI976-760 Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1328 seconds