Having problems with your Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher ?

Our Fisher & Paykel single dish drawer unit (6 months old) is leaking limited water from its base down the front of bottom drawer below the unit's base onto the kitchen floor. One inspection by a technician failed to find any rectifiable problem. Unhappy, Wicks Road North Ryde


Answers :

One drawer leaks can cause this problem. If you don't fix it. One day it will turn on the pumps from both units without any one touching them since the floor sensor at the bottom housing detects water and it will run for ever until you unplug the power cord.\015\012This dishwasher is a state of art in design and replacing parts is very simple once a person has enough understanding of its mechanism. If the tech fail to find the problem then he is not qualified to touch this dishwasher.\015\012When there is a leak, it is a problem with the lid seal from the top not closing down tightly so during the wash cycle, water shoot up and leaks through the top opening then collecting on the bottom housing of each unit. Let say the top draw is leak, so the bottom housing of top draw if full of water then it overflows to the bottom drawer unit then the floor.\015\012Here is the idea of how it happens.\015\012The top lid is pulled down by 2 actuators from both sides at first start. That is why you can hear the motor noise turning on at the beginning of the wash cycle. That is the noise from the actuators. If the actuators are bad. only one side works then the lid can not be sealed properly there is a leak. If bothe of actuators are week the gear worn out so they can not hold the lid down during the wash cycle then it can cause a leak.\015\012You can pull each tube out and access from the left side at the bottom to touch the bottom housing to fell the wetness. Put in tower to dry them out. If there is a weteness from the bottom housing upper tube it doesn't mean the bottom drawers is leaking. It is wet just because the top is leaking. However you have to dry the bottom in order to continue use the bottom dryer. If you ignore my advice then your circuit board at the bottom housing of lower drawer will be damaged and it is not cheap. \015\012With the information that I provided you can interview a tech claiming know about the this type of dishwasher before letting him coming into your house. Good luck.
Repair Help & Product Troubleshooting for Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Our Fisher & Paykel single dish drawer unit (6 months old) is leaking limited water from its base down the front of bottom drawer below the unit's base onto the kitchen floor. One inspection by a technician failed to find any rectifiable problem. Unhappy, Wicks Road North Ryde


One drawer leaks can cause this problem. If you don't fix it. One day it will turn on the pumps from both units without any one touching them since the floor sensor at the bottom housing detects water and it will run for ever until you unplug the pow ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

Due to the my Indesit IDL 530 dishwasher not draining properly, I turned it onto it's left side, removed the base plate and pump and checked for blockages in the pump and associated hoses, which were all clear. However in re-assembling it I have forgotten which way round to connect the twin wire plug to the base plate. I cannot find a relevant wiring diagram online and therefore cannot tell which is the correct way around. I then guessed and re-assembled it anyway, and as you might have g


Hi.There is more than one wire going from control board to the tub. If the connector can be plugged either way without forcing it, then usually does not make any difference the way you plug this determined connector. It will be usef ... Hotpoint 24 in. FDW60 Free-standing Dishwasher

I just bought a used Kenmore portable dishwasher with Model #587 1749581. I'd like to find an owner's manual and parts list for this...in particular the hose adapters to fit onto a kitchen faucet. Can't seem to find such. Do you know how old this dishwasher is and if parts are available?


You should be able to go to the Kenmore web sit and down load a manual. If there is a manual you can get it on line. Try google put the model number right in the search. ... Dishwashers

I have a Miele G892 SC dishwasher. When I start the cycle, it drains (except for a bit of water left below the triple filter). After that, the intake valve opens and water enters. It then does nothing for a period of time until the "intake/drain" indicator light starts flashing. When I open the unit, I find about 1/2in of water in the tub (above the tripe filter). I have 1. cleaned the intake valve filter (no blockage found) 2. Inspected the drain line at the base of the unit as well as t


The pump is running due to the float switch or the float itself either being stuck open or broken and showing a fault this is why you have water going in to a certain point but not the point required for washing the dishes and then due to the float s ... Miele Dishwashers

Kitchenaid kuddo1dppa I own a KitchenAid KUDD01DPPA, 2 drawer dishwasher. I am not a technician, however I have had a lot of experience in repairing various appliances and am savvy with electronics and mechanical technical issues. Here's the problem: I was getting rinse error codes in both drawers, pulled the bottom drawer out, removed the cover to the circuit board and used a dryer to dry up the moisture on the flood switch. Now I am getting Fill Failure error code on both drawers. I have g


Test this steps and fix it. God bless you\012 \012 Water Inlet Valve\012 \012 \012 \012 \012 \012 \012 \012 \012 ... Dishwashers

Why is my kitchen aid superba refrigerator leaking water? There is no condensation drain that i can find on that side. It is a side by side.


... KitchenAid Kitchen Aid Superba Series Dishwasher Used Kuds011jbt0

Removed rear toe-plate to detect leak. Leak caused by broken drain hose. Hose replaced. To do this the unit was tipped forward onto its front door to allow access to the base area. Water allowed to drain out the front base area. Unit re-assembled but now does not switch on. Water connected. Base-plate dry. No water was detected at upper-front control panel. Power is connected and reaching unit ( multi-meter test ). Tipping the unit forward seems to be the cause. Is there any fuse,


The micro switches are frequently replaced on the door handle and they don't need to ever get wet. A lot of amp draw burns those switches up while they are dry. If they were wet and power was applied then they got fried my friend. The good news is th ... Dishwashers

I bought a used 7 1/2 year old fisher paykel dd603 for my tenant, it worked fine the first time. second time she got F1 code on both drawers. water was in lower pan, we sopped it up and dried it out. also drawer was not seating level but was lower on left side, and insulation had fallen off left wall. all now corrected. but now the top drawer leaks onto floor on left side. it did not leak before repairman came out, we checked thoroughly. repairman says top lid not seating properly and i need ne


I have the same model F&P and just experienced similar problems. My top drawer was leaking due to that "not important" thin white tube. It really sounds like you called a general appliance guy and not a trained F&P repairman. The guy who fixe ... Fisher and Paykel 23 in. DD603H SS Free-standing Dishwasher

Fisher Paykel top drawer lid interferes with opening and closing of drawer. Have top drawer removed for inspection. What to look for?


... Fisher and Paykel 24 in. DD603H W Built-in Dishwasher

Just looking for some advice on removing the drawer from my servis washing machine, sorry I dont know what model it is. I need to clean the powder drawer but cant find any way to remove it from the machine. There is no internal part marked push that i can see and im wondering if i need to unscrew the four screws around the drawer. Help please! Cheers


Send an email to this address asking for the user guide for your model \015\012\015\[email protected] ... Servis Dishwashers

How do you remove the drawers on a kitchen aid 2 drawer dishwasher?


... KitchenAid KUDD01DSSS Built-in Dishwasher

Bimetal fuse The incoming power was blinking off and on due to a storm, it caused the bi metal fuse to fail in the dishwasher when it was not operating, the fuse was replaced with kit #w10258275, now two weeks later the fuse has failed again while operating.These fuses are expensive, I would like to know the value (amps) of these fuses so that the system can checked to try and find out the reason for failure, or maybe you might have an idea where to start. Thanks Tad


... KitchenAid 24 in. KUDI02IR Built-in Dishwasher

My kids put liquid dish soap (not for dish washers) into the hole where you put special rinse product. We got all the soap out of the hole and took towels to dry out the tub, but F1 comes on even when the washer is turned off. We have the double tall dish drawer in stainless steel. Even though they did not put anything in the bottom drawer it too comes on by it self and shows F1. I can not find our manual. Please help. Thank you so much. Kim Toth


You can download the user manual but that may not help you solve the problem.\015\012\015\012I can see that there has been foam ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

My model # is 8573030. the machine is about 4 years old. the control panel failed after about 1 1/2 yrs. it has failed again. can I fix this myself? if so where can I find the parts?


Hi there. The correct part number for your replacement control board will be W10084141. The original control board that was shipped with this unit dose not exist anymore, at this time. Due to this f ... KitchenAid Dishwashers

The soap dispenser that comes with my kitchen aid kitchen sink is broken. How/where do I find a replacement?


You can get replacement soap dispensers on the link below.\015\012\015\012http://www.kitchensource.com/bathroom-si ... KitchenAid 24 in. KUDI01FLSS Stainless Steel Built-in Dishwasher

My Kitchen Aid two drawer dishwasher started not draining all the water out, Then a few days later it would not stop running., both drawers. It only stopped when the circuit breaker was turned off. What is wrong? Does this dishwasher has a cancel button?


... KitchenAid Dishwashers

Top drawer leaks onto floor. bottom drawer works ok.


Looks like you were being helped by another consultant. Unfortunately I do not have access to what solutions were suggested. But reading in between the lines it appears you are checking if the lid seal is moving correctly.\015\012\015\01 ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

I have a Fisher/Paykel dual drawer dishwasher and the top drawer now makes a loud grinding noise - appears to be coming from the front of the unit. Any thoughts? Any home-based solutions?


I agree Vladimir.... you can pop out the rotor assembly very easily, just turn it in the direction of the arrows, then push something through from the filter end, a drinking straw or such like, you'll probably find something stuck in there! ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

Just installed fisher paykel model 88270 dishwasher, bottom drawer has no power,and top drawer does not fully drain. Cant find another power cord, is there a second one? Cant locate the manual.


... Fisher Dishwashers

Kitchen Aid Dishwasher KUDS03ST We built our house and had this dishwasher sitting in the box for almost 2 yrs before finally using it. After finally installing it I find that occasionally the door to the soap does not open for washing as I find out when the dishes are supposed to be clean and I open the door to hear the soap then pop out of the dispenser. How do I fix this problem?


I have seen a lot of dishwashers that have this problem if they have a flip open lid for the soap .. often its caused by the top adjustable tray blocking the soap door from opening .. i put a camera inside to figure out what was happening ..in some ... KitchenAid Architect? II U SERIES KUDS03ST Stainless Steel Built-in Dishwasher

I have a Karcher K3.48M electric pressure washer which used to shut off when you weren't using the cleaning wand. This no longer happens and there is alot of water running out of the bottom of the unit. (This didn't used ot be the case) I expect a leak somewhere inside the unit, but I'm wondering even more if there is a pressure switch which has failed that cased the leak. In other words, if I find and repair the leak and there is a failed pressure switch, it will likely only break again. I can'


Hi you will have a 8 digit number on a silver plate on the machine with a number like 1.141-470.0\015\012Then go to www.karcher.com then on the left click on Europe, then you ... Karcher PSI Electric Pressure Washer

Code F2 I just replaced the door switch on an inoperable DD-602. My top drawer was working fine, but my bottom one has been offline for a while (door switch failed and I never got around to fixing it since I had the top). Well, my top finally failed too so I replaced both switches. Looks like everything is good on the top, but my bottom is erroring with an F2 code now. Kindof makes a thumping noise as it starts the cycle -- maybe 3-5 short thumps and then a 10 second delay, repeats. Any ideas? C


F2= \015\012The motor has not\015\012been sensed rotating\015\012\003 Foreign object has jammed the rotor\015\012\003 The rotor has failed\015\012\003 The hall sensor has failed\015\012\003 The electronic controller has ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

Water Leak My dishwasher is an Ariston Advantage AF250: I have been told that internally its the same as a Hotpoint DF55. It intermittently leaks water onto the floor from the front at its base during use. At one time it ruined the motor which I had rewound and at the same time I made a new polystyrene float for the base pan overflow switch. All was well for months, but now its leaking again. I have blown through the tubes from the drain filter well to the pressure sensitive switch, but all


Hi there, dishwasher leaking might be due to either of these causes, check these:Main tub sealNote… If the main motor of your dishwasher is mounted vertically, beneath the center bottom of the dishwasher, the foll ... Hotpoint 24 in. DF55 Free-standing Dishwasher

Hey, I have a dual drawer DD603-SS and the LCD light just went off on the top drawer unit(everything else works)!!!! Any think I can do before calling a technician?


Most likely the LCD unit has had it or the connection from the controller is loose. In any case you will have to open the front panel and the door cover. Best to call the technician if you are not familiar.\015\012\015\012Try tuning the m ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

How do I get inside a Bosch dishwasher? I am trying to find out what is wrong with the heater in our Bosch S210 . I can't find how to inspect the components without breaking it. What is the trick?


Just go into the bath :) ... Bosch Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0783 seconds