Having problems with your Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher ?

Have a dd603 with an issue...took off the arm and the metal silver disk (the ones with holes) to get to the wash impeller-(the thing with blue blades) the wash impeller will not spin-which I think is part of my problem, since i looked at the lower drawer and was able to spin the blue blades easily...was also able to pull it right out. Cant pull out the upper wash impeller!!!! Really want to get this fixed before my husband gets home and I get the lecture about how I purchased a cool looking d


Answers :

Lol I don't know a lot about dishwashers, just do him good and tell him afterwards, and then hire a mechanic to look at it.
Why would you want to pull the propellers off anyway? The top one doesn't pull off because it's screwed on, and the bottom one probably just sits on there.

Sorry but my expertise is computers, you could check in the User's Guide:
http://www.fisherpaykel.com/admin/pdfs/pdf_usecares/527971B_DD_user_guide_USw.pdf

Hi,

The Impeller would not move, if it is 100% worn out. More often it would result in Dirty Dishes.

I am afraid to say, it is a Costly Repair and it is common with most of the Washer's. Only a Qualified Tech who have worked on these Models, would be able to replace this.

I am sorry, but a Service Call is a Must in this case.

Let me know, if needed further assistance.

Hope i helped you.

Thanks for using ' Fixya ' and have a nice day!!
Repair Help & Product Troubleshooting for Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Have a dd603 with an issue...took off the arm and the metal silver disk (the ones with holes) to get to the wash impeller-(the thing with blue blades) the wash impeller will not spin-which I think is part of my problem, since i looked at the lower drawer and was able to spin the blue blades easily...was also able to pull it right out. Cant pull out the upper wash impeller!!!! Really want to get this fixed before my husband gets home and I get the lecture about how I purchased a cool looking d


Lol I don't know a lot about dishwashers, just do him good and tell him afterwards, and then hire a mechanic to look at it.Why would you want to pull the propellers off anyway? The top one doesn't pull off because it's screwed on, and the botto ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

My kitchenaid dishwasher won't wash. The clean light blinks and if I can get it to cycle, it turns on to ''2 minutes'', during which 2 minutes it makes some washer-like sounds but doesn't clean, dry or spit out any water. Before this, I wash having trouble getting my dishes clean. I wash able to get the bottom rack clean using the heavy duty cycle, but the top rack still didn't clean


... KitchenAid Dishwashers

I am not able to get a siemens front loading washing machine at the right price. first they told me that the model was not available now the price of the model in india is too high for the features that are in it. I doubt whether it is a siemens model itself. kindly call me on 8975764416 immediately please. i tried to contact the england phone number also but it was wrongly given in the website of siemens. please help me to get WM14S79BUK or WM14S794ME model of washing machine at the right


... Siemens 24 in. SE25A266 ExtraKlasse Free-standing Dishwasher

My Kenmore Elite dishwasher doesn't wash dishes properly. I think that it is not getting enough water in the machine. It only allows about an inch of water to get into machine and then starts. I do not think that there is enough water to spin wash arms. I have 40 PSI coming into the house. I am on well water and found debris in the intake orfice. I did my best to flush. Could it still be bad?


I am having the same problem with my brand new Dishwasher. ... Kenmore Dishwashers

I have a Frigidaire UC DW Model FDB250RHB2 The unit is not a year old. It is not getting dishes very clean. I read similar posts. I found that there is water coming from top nozzle but not a very impressive stream. It is weak enough that most of the water misses the funnel on top rack. Also not top or bottom arms spin. Last week when i would quick peek during wash cycle there seem to be water coming out of top arm's holes but no spin. We also are getting heavy white staining on glass ware


... Frigidaire FDB520RH Builtin Dishwasher

Impeller is spinning counter clockwise on the wash motor.


... Maytag 24 in. MDBH950AWS Built-in Dishwasher

My 6 hp honda motor has become very hard to pull. It is on a pressure washer. I even removed the pump but still pulls hard.it runs if you can get it started but dosnt seem to be running at full power.I pulled the spark plug and it spins easily. Help!


When you remove the spark plug and it turns easily that means that the valves aren't opening properly. When the spark plug is installed and its hard to turn over, its because the valves (possibly just the exhaust valve) are sticking shut and the pre ... Pressure Washers

Bosch Integra SHU 9955US/12 - when we start wash cycle, the detergent dispenses and the tub fills with water, but the wash cycle never starts (never spins spray bars). Seems like timer is counting down, though, but doesn't start "washing". After waiting awhile, we are able to use the "Cancel/Drain" mode to drain the water. The drain filter in the bottom of the tub is clean.


Sounds like your motor is burned out. The drain motor and wash motor are seperate on your machine. You can check for power going to the motor, but to do this you might have to pull the dishwasher out. While the cycle is running check for 120 VAC g ... Bosch SHU9955UC Built-in Dishwasher

Hi, my hotpoint aquarius df61 makes all the noises of washing, i hear the water going in, motor is running, however i dont believe the spray arms are revolving, so the dishes are not getting clean. i have cleaned the individual holes in the spray arms, but i don't think the water is getting up the back pipe and into the top spray arm. it does not spin at all. no problems draining. help please. and were can i get a copy of the user guide, free preferably. thanks


How old is your machine? it is posible to have something in the watwr pump, you hear the water and the motor, but the fan of the pump (washing pump) is blocket. also the pipes hat make connection to the water pump and the arms. at someoane i found gl ... Dishwashers

I have a Troy bilt 2700 psi pressure washer and I can't get the pull start to pull all the way. It pulls part way and is stuck. The last time I was running it it shut down on its own and I haven't been able to restart it since. Thanks


... Pressure Washers

F2 Code Hey, I have a single drawer built in Fisher & Paykel dish drawer and today I pulled the spray arm, filter and large metal screen out to clean them as we have been starting to get a bit of stuff left behind after washing lately. That was all good After putting it all back in though I went to use the dishwasher and it stopped and came up with an F2 fault, I thought I may not have put the bits back in properly so pulled them out again and noticed that on the rotor that connects the motor to


Fault F2 means the rotor is not rotating. If you say some of the vanes have broken off, they could have been jamming it. This should spin freely with minimal force when installed correctly. If you removed the rotor itself, you do ned to take care whe ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

Whirlpool adp 8540 dishwasher not washing properly. Not getting enough water pressure to spin the arms or even take the granules out of the wash powder compartment. Have checked hoses and water supply all Ok. Is is something simple that can fix myself or do I have to call an expensive repairer? L


I have had the same problem, for me it was caused by small pieces of food, normally woody grains, it blocks the outer jets.\015\012\015\012When looking you may not see that it is blocked because they seem to move around.\015\012 ... Dishwashers

The dishes in my dishwasher are not getting clean, particularly on the upper rack. It seems to be because the upper water arms are not spinning during the wash cycle. The bottom spin arm is working fine. I have cleaned out both upper arms as best as I could without removing them (above and attached below to the upper rack), as it does not appear that these arms are easily detachable. I am thinking maybe water is not making it up the line to the upper arms? I also have a lot of dirt in the b


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks for using FixYa. First of all please check the\015\012Water temperature by using a thermometer inside the dishwasher to measure ... GE Dishwashers

I have a Triton dishwasher. Last cycle, it completed washing then started drying and started beeping and the drying light is flashing. When I finally opened the latch, the beeping stopped, but the drying light is still flashing. The dishes were clean and warm - they air dried the rest of the way. I have not been able to get the drying light to go off. I have turned the breaker off over night, and flipped back on. The dishwasher goes back to flashing washing, and then clicks to drying and th


Hi,\015\012Make sure the salt level is ok - add 1Kg of salt if you have not done it in a while, and check rinse-aid level if apliccable.\015\012\015\012If this does nothing, then remove the lower kick panel for access to a data shee ... GE Dishwashers

I have a Whirlpool Gold Quiet Partner III that is 8 years old and recently stopped cleaning top rack dishes. I remember finding a mylar like piece in the bottom of the tub and threw it away thinking it came off of something we washed (I know, bad thinking.) The mylar piece measured roughly 3-4inx2in and was folded in half. Anyways....the upper arm does not spin and the detergent doesnt get fully dispensed so dishes dont get fully cleaned. I am guessing not enough water pressure to upper arm. Wou


I'm having a similar issue. Are you sure the arm isn't moving at all?\015\012\015\012Generally what I'm finding is either you have a clog or the pump motor is bad.\015\012Hear is the service manual.\015\012 ... Dishwashers

My Kenmore ultra wash dishwasher fills with a little bit of water but does not spray water and does not proceed through the wash cycle. Any advice? We had problems yesterday with blinking lights and not able to get anything to work except the drain. then we followed a sequence of pushing buttons and it solved the first problem.


The spray arm rotates based on the water pressure coming out of them. If no water pressure, then no rotation. You probably have a clog on the intake hose. You can pull out the dishwasher, tip it forward so you can get to the bottom and then rem ... Kenmore Dishwashers

TOP ARM HANGING DOWN-Dishwasher's working fine, problem is that the wash arm/spray thing at top is lower than it used to be, we only noticed because when pulling out the top rack the top arm/spray thing at top gets hit by the rack. Work around has been lifting rack up at angle to get past this, but everyone at some point forgets to do this and we are worried eventually something will break. HELP???


... Dishwashers

Hi I have a mdb6601awb maytag dishwasher. Sometimes when it starts the wash cycle it will make a loud squelling noise. Then if you pull on the handle and stop it, the machine will start and sometimes the noise will be gone. Or you may have to do this 3 or 4 times before it will stop making the squelling noise. I do notice when I pull up on the handle to stop the machine it makes some clicking noises and then the noise goes away. Thank You for any help you may be able to give me!!!


I don't have a solution however I have the same problem with that same model. ... Maytag 24 in. MDB6601AWS Stainless Steel Dishwasher

All aspects of the dishwasher work except the wash motor/pump does not run. Is it the motor? I have taken the lower arm assembly apart and removed the support to spin the impeller. It spins fine although there is axial play.


If the shaft is moveing from side to side you need to replace the motor. did you tern the impeller around about 3 complet terns? ... Dishwashers

Whirlpool adp 8540 dishwasher not washing properly. Not getting enough water pressure to spin the arms or even take the granules out of the wash powder compartment. Have checked hoses and water supply all Ok. Is is something simple that can fix myself or do I have to call an expensive repairer?


... Whirlpool Dishwashers

The water is not getting up to the middle spin bar or the top one, so nothing on the top rack is getting cleaned and everything is left with soapy film, so it is not rinsing properly. There is water coming in at the side for the intial fill and from the bottom to wash.


Thanks for your question!I'm sorry that you haven't received an answer yet.The response rate on FixYa FREE questions is usually over 80%, but sometimes questions go un-answered when:1. the question is unclear, incomplete, or poorly ... Frigidaire Professional Series 24 in. Built-In Dishwasher Dishwasher

I have a Bosch dishwasher model #SHU3032UC/U12 It is not pulling water from the water pipe to wash the dishes the motor wants to go thru cycles. It starts to pull the water by the sounds from the sink but no water gets into the dishwasher.


Hello. When no water is entering the dishwasher, there are two parts to check. \015\012Water-inlet valve\015\012\015\012\015\012\015\012\015\012\015\012\015\012\015\012The water-inlet valve lets water enter the machine. If this ... Bosch Dishwashers

I Have a Kenmore Ultra wash Quiet Guard. I accidently poured finish liquid dish detergent into the rinse aid compartment and don't seem to be able to get it out of there. Put it through a few cycles and it still shows full. Can I get it out somehow. Thanks


... Kenmore 24 in. 15689 Built-in Dishwasher

Makes rumbling noise during wash cycle. I've pulled the pump and found no debris. It's been making this noise for about a year now. No problems with our dishes getting washed. Do you think the bearings inside the motor may be bad? If so, would I need to replace the motor and pump assembly?


... GE 24 in. GLD5560LSS Stainless Steel Built-in Dishwasher

I can't pull the cord out in order to start the unit. Even took the spark plug out. The unit was running fine then quit. No unusual noises or anything. Sitting on a deck so nothing was able to get underneath.


... Pressure Washers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1641 seconds