Having problems with your Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher ?

Fill Fault appears during wash cycle.

\015 MODEL: DD603\015\012Product#: 30188-B\015\012Serial#:RAM710040\015\012\015\012Hi there, \015\012\015\012During the wash cycle a tap symbol appears (with a line through it/ fill fault) on the LCD during wash cycle. The machine then stops washing and continually beeps allowing the drawer to be opened.\015\012\015\012Pressing the start button again continues the wash. Sometimes the fault reappears twice or more in the one wash cycle.\015\012\015\012What is causing this "fill fault" to appear? ...and so regularly?\015\012\015\012Thanks in advance\015\012\015\012Stephen\015

Answers :

Is the filter in the hose where it screws onto the tap clean?, if this is okay then most likely the valve.
Repair Help & Product Troubleshooting for Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Fill Fault appears during wash cycle.


Is the filter in the hose where it screws onto the tap clean?, if this is okay then most likely the valve. ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

E1 fault code Dishwasher runs for about 5 minutes. Water fills up at bottom of unit and then machine seems to pause then fault code E1 appears then water is pumped out from bottom of machine. There are no leaking pipes and drain is installed correctly. I installed a new wash pump and fault still appears.


Hi,\015\012I think both the heater and thermostat / trip switches need to be checked.\015\012If water is going in and out ok, then it seems to be waiting to heat the water. It sees a fault - so just clears out.\015\012Heating elemen ... Dishwashers

After fill cycle ,theres a crackling/popping noise for five[5] +- seconds after start of wash cycle. Noise appeares to be in wash pump.


... Jenn-Air 24 in. JDB1250AWS Stainless Steel Built-in Dishwasher

Serial #88445-B Rym 717881 model # fpdd 603 We are getting a fill fault code when we start the dishwasher. When the alarm goes off we have to pause the wash cycle open the door and then close the door if we do this about 2 or 3 times it will wash. It seems it fill with water but it seems to be low on water Dave Heller


... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

Bosch SHU43C My Bosch SHU43C is stuck with the drain pump running. I ran the self-test and it gave me the fault code 4 wich indicates a filling fault. The washer is empty and all wash cycles display the correct number of minutes for the cycle. It counts down to 0, but the pump continues to run. Does this indicate a stuck float, or is the problem with the control board? Where is the float located? Are diagrams/pictures available on-line anywhere? I've done some searching, but haven't found any. R


My SHU43C is just over 3 years old. I had a similar problem recently. First, there were a few floods. Then, the Bosch only drained non-stop. Even when I used the Cancel Drain buttons the drain pump would run without stopping. When I ... Bosch 24 in. SHU43 Built-in Dishwasher

FDW60 Error code 3&4 . After reset m/c drains on all cycles. Start new cycle, m/c fills but then cycle stops. Makes bubbling noise and appears to overheat. Fault is same on all cycles. M/C drains on all cycles following reset.


... Hotpoint 24 in. FDW60 Free-standing Dishwasher

I think I need to check the water pump/motor on my Bosch SHU43C dishwasher. It seems the water enters at the start of the wash cycle but then there is silence through the remainder of the cycles. Water will not spray. The drain appears to work ok to drain most of the water out. I have the washer out and upside down. Any hints on removing the base to get access to the pump? Should AI be looking at the control panel also for a fault? (the cycles seem to count down ok)


Click below;\015\012Latest Bosch Dishwasher Use and Care Manual\015\012\011\011\011\011May 4th, 2008 by Samurai Applian ... Bosch Dishwashers

FDW60 Fault Hi, I have exactly the same problem. My dishwasher starts and washes ok but appears to get very hot during the drying phase and then the two lights fast and eco flash warning of a heater problem. I suspect either the heater, thermostat or control PCB. As the rest of the cycle seems of and the water gets hot then I'm assuming the heater and thermostat are OK. When the dishwasher attempts to dry is when the problem starts. Did anyone find out what there fault was? Thanks


Hold down the start key and you will re- set the D/W. Please Rate This !!! Thank YOU !!! ... Hotpoint 24 in. FDW60 Free-standing Dishwasher

My Kenmore dishwasher model number 665-16389300 is starting to fill up and not drain during the normal wash cycle. Water will run out on the floor. When we hit cancel and drain it appears to drain just fine so I dont know if it is a pump issue or something in the cycle. What do you think?


... Kenmore Dishwashers

My bosch excel dishwasher has the following fault: start the cycle, water starts to fill but then check water light comes on and it then starts to empty again. Pump then keeps going. I have checked the hose and even swapped it round with my washing machine one but this makes no difference. I have cleaned all the filters and taken off the cover to check the 'propeller' as sugested in the instruction manual. But no joy - check water light still illuminated and willnot continue with cycle. - Help!!


This unit im sure has a water flowmeter that measures the water intake.. if this cannot read then the unit shuts down to avoid flooding.. \015\012it needs replacing... it is attached between the valve and the side tank or attached to the tank d ... Bosch Dishwashers

I have a Kenmore Elite dishwasher (model 665.1315), and the dishwasher will run through the wash cycle as expected, but when it gets to the heated dry cycle , it doesn't appear to dry. It will then flash a fault code 81 (8 short flashes of the 'clean' light, pause, and then 1 more short flash of the 'clean' light, longer pause, and repeat the code). The dishes seem to be somewhat dry, but there is certainly water on the dishes and on the tub (there is never any water standing in the tub, and t


Hi,Check your heating element.. \012A bad heating element causes many problems in dishwashers...Dishwasher Problems The ... Kenmore 24 in. 15932 Built-in Dishwasher

I just installed a new Kitchenaid dishwasher (Model KUDE60FVSS3). After filling with soap, closing the door and starting the machine, it fills with water, waits a couple of minutes and then I can hear low humming noices coming from down below. After opening the door it appears that neither spray arm has turned as if to wash. This dishwasher was purchased new a few years ago and kept in storage as our basement was being finished. This dishwasher has never completed one cycle. Any and all inf


If you have a garbage disposal, there is a plug in the dishwasher that has to be removed for the washer to drain. ... KitchenAid KUDE60FVSS 24 in Builtin Dishwasher

Kenmore Limited Edition Ultra Wash Dishwasher. Model 665 15892100, Ser. FL4910642 E71195, Stock #15892. Loaded dishwasher, started it, and went to store. When we came back, it appeared cycle had not completed (greasy and wet dishes) and the dry cycle had definitely not run. Bottom of dishwasher is filled with water. Tried to cancel/start the machine but control is completely blank and does not respond.


Hello,Welcome to FixYa.The issue with your dishwasher is more than likely the "thermal fuse" inside the control panel...it is all too common with those machines unfortunately.I've at ... Dishwashers

Our Maytag MJD3005 dishwasher got a couple of minutes into a cycle then displayed E4, stopped and beeped. I cleaned the filter basket out (which needed doing), powered down and up and restarted. Then a couple of minutes into the cycle E2 appeared as (I think) it doesn't enter the wash phase (fills OK). Repeated on different programs with the same outcome. Any clues?


... Maytag Dishwasher

Our Bosch SGS 53E02 AU/30 Dishwasher has the Tap Light on all the time while the Dishwasher is filling up. It appears as though water cannot get through and takes a long time to fill. It also does not allow the wash cycle to start and the powder door does not open. Can you also get any Service manuals for this model?


... Bosch Dishwashers

Dishwasher Westinghouse SB915 fills with water for wash cycle but does not wash.


... Dishwashers

My dishwasher (indestit) will not fill up with water. A technian came today and advise that there was very little water coming through the hose and therfore had a blockage. I replaced it today and it fixed the problem, however onn the 1st wash the cycle appeared to stop rather than completing fully. I have since tried to restart and have the same problem lights 2 and 3 are flashing indicating there is no water getting through, how can this be.


Hi,Here is a tip that will help you to find out why water will not come into thedishwasher... Dishwasher Trouble No Water entering Dishwasher ... Dishwashers

I have a whirlpool DU915 built in dishwasher. During the last pre wash cycle after filling with water, it suddenly stopped and the lights on tne control panel went out as it was suddenly unplugged. All connections are still intact, the breaker box to the house has been checked. The shared outlet is still working, as the garbage disposal still operates normally. The latch on the door appears to be functioning. Can you please give me a direction to look?


... Dishwashers

My Kitchen Aid KUDS01FLSS2 dishwasher does not spray water thru the wash arms nor do they seem to turn. Additionally, one of the the bottom arms hits the "cap, internal rear feed" where it clips to "feed tube assembly" when rotated by hand. The spray arm assembly appears true on visual examination. The unit fills, cycles and pumps out in an apparent normal way. While on this site a while back I was advised to clean the unit and referred to a downloadable repair manual that was, in fact, not


Hi.The fact that "one of the the bottom arms hits the "cap, internal rear feed" where it clips to "feed tube assembly" would suggest a tubing problem. However there are more faults that will result in no spray. Testing in this case can be ... KitchenAid Dishwashers

The dishwasher will fill with water but when it trys to start the wash cycle it just makes a huming noise like you would hear when an electric motor is frozen. you can cancel and and it will drain with no problems. i checked the chopper and it spins freey and it appears that the shaft driving the chopper is not frozen. just curious what parts i need to purchase. thanks very much. richard lester


... KitchenAid KUDS01FKSS Dishwasher

Commercial Dishwasher G7856. During main wash cycle fault code F3E appears and machine stops.


... Miele Dishwashers

I have a Baumatic Dishwasher BFD63ss and it won't complete a cycle. About 5 mins into the wash it bleeps and the display shows fault code 002. It dones't appear to be getting hot either.


... Baumatic Dishwashers

I have run the test cycle and the quick wash and pre-rinse lights are illuminated. Does this mean a water sensor and filling fault?


... Bosch 24 in. SGS45E02 / SGS45E08 Exxcel Free-standing Dishwasher

My dishwasher won't drain. It runs through the whole wash and dry cycle...and when I open it to unload the dishes the bottom is filled with standing water. None of the lines that I can see appear to be kinked, and I'm not sure what else to check. I inistalled the dishwasher myself becasue my husband was working out of town...this was about a year ago. Haven't had any problems with it until now. Thanks for any help or suggestions you're able to offer. Christine Fitzpatrick


If you hear the drain pump run after wash and rinse cycles then it is likely the problem is in the kitchen drain end. Have you got a disposal unit in the kitchen sink. Sometime it is full and causing a block.\015\012\015\012If you don't h ... Dishwashers

Model: Whirlpool ADP 4501/5 (4 years old) Problem: Dishwasher won't start wash cycle. Green light flashes 11 times. After adding a bucket of water to the dishwasher it runs normally. Checked the inlet valve and it appears to be fine. Filled the salt container and it solved the problem for a while but having the same problem again. Any suggestions would be appreciated.


... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1346 seconds